Effect of uniaxial stress on the dielectric properties of BaTiO3+0.1wt.%Eu2O3 ceramics

ABSTRACT

BaTiO₃+0.1wt.%Eu₂O₃ ceramics were prepared by a solid-state reaction method. The dielectric behavior of these ceramics as a function of uniaxial pressure has been systematically studied. The external stress showed obvious effects on these properties. An increase of the Curie point (T_c) and decrease of the Curie–Weiss temperature (T₀) was observed with increasing pressure, resulting in an increase in the first-order nature of the phase transformation (T_c–T₀ increases). Broadening and flattening of the permittivity versus temperature curves near their maximum was found. The pressure behavior of thermal hysteresis and the ??/?T vs. T plot suggests that the phase transition changes to second-order type with increasing pressure. Furthermore, the Curie–Weiss constant obtained from a modified Curie–Weiss law strongly decreases with increasing pressure, suggesting that the mechanism of phase transition is going to order–disorder type.     

Effect of heat treatment on the structure and morphology of ZnO nanorod array and its composite with titania precursor

ABSTRACT

Effects of the elevated temperature on the structure evolution of the ZnO nanorod array (ZNA) and their hybrid nanocomposite with layered (tetramethyl)ammonium titanate (LTMAT) prepared by the liquid phase deposition were investigated. The vertically oriented ZnO nanorods were deposited on a quartz plate by a chemical bath deposition method and then they were penetrated by the LTMAT using the dip-coating method from the water solution. As a result of such an experimental procedure, an assembly composed of the ZNA with LTMAT was obtained and called hybrid nanocomposite. Since the LTMAT converts to TiO₂ upon subsequent sintering at 350 °C, it can be regarded as TiO₂ precursor for the thermal treatment experiments. The experiments with ZNA and their hybrid nanocomposite at the elevated temperature revealed coalescence of the deposited ZnO nanorods and crystallization of zinc titanate with Zn₂TiO₄ stoichiometry.     

同轴结构中压力波法测量空间电荷分布的物理模型研究

从压力波法测量平板样本中空间电荷分布的理论分析出发,提出了对于同轴结构的固体电介质中空间电荷分布的压力波法测量的物理模型,并得出了测量电流的解析的数学表达式.依据泊松方程,考虑样品内的电场强度、介电常数和空间电荷密度随外界声波扰动而发生变化,将圆柱试样受到的压力波的影响分解成样品形变和质点位移两部分,进而得到了以同轴结构中空间电荷分布的压力波法测量的电压与电流表达式.测量电流的数学表达式表明,对于同轴结构,压力波法的测量电流信号不像平板结构中那样基本正比于空间电荷分布,而是应该做进一步的修正处理.     

原子层沉积技术沉积的FeOx包裹层显著提高Pd/C催化剂在甲酸分解放氢反应中的催化活性

Hydrogen generation from formic acid (FA) has received significant attention.The challenge is to obtain a highly active catalyst under mild conditions for practical applications.Here atomic layer deposition (ALD) of FeO_x was performed to deposit an ultrathin oxide coating layer to a Pd/C catalyst,therein the FeO_x coverage was precisely controlled by ALD cycles.Transmission electron microscopy and powder X-ray diffraction measurements suggest that the FeO_x coating layer improved the thermal stability of Pd nanoparticles (NPs).X-ray photoelectron spectroscopy measurement showed that deposition of FeO_x on the Pd NPs caused a positive shift of Pd3d binding energy.In the FA dehydrogenation reaction,the ultrathin FeO_x layer on the Pd/C could considerably improve the catalytic activity,and Pd/C coated with 8 cycles of FeO_x showed an optimized activity with turnover frequency being about 2 times higher than the uncoated one.The improved activities were in a volcanoshape as a function of the number of FeO_x ALD cycles,indicating the coverage of FeO_x is critical for the optimized activity.In summary,simultaneous improvements of activity and thermal stability of Pd/C catalyst by ultra-thin FeO_x overlayer suggest to be an effective way to design active catalysts for the FA dehydrogenation reaction.     

电沉积Ni-W梯度镀层及耐磨性研究

通过电沉积技术并调节镀液中镍钨离子配比浓度在铝合金基体表面制备了Ni-W梯度镀层,研究了镀层中W质量分数的变化对梯度镀层性能的影响.结果表明:所制备梯度镀层表面均匀平整,与基体结合良好,沿镀层生长方向W质量分数逐层增加;相比于Ni-W均质合金,Ni-W梯度镀层具有较低的摩擦系数,磨损形貌较为平整,表面剥落少,表现出较好的耐摩擦磨损性能.     

CrAlN涂层海水环境腐蚀磨损行为研究

采用多弧离子镀在316不锈钢上沉积Cr Al N涂层,用X射线衍射仪(XRD)和扫描电子显微镜(SEM)表征涂层的成分和结构,纳米压痕和划痕仪分别测试涂层的硬度和结合力.通过球-盘往复式摩擦磨损试验机在海水环境下测试涂层腐蚀磨损性能,并用电化学工作站实时监测其摩擦过程中的电化学特性.结果表明:Cr Al N在有摩擦的条件下,涂层极化曲线的阳极区域存在较为明显的钝化区,抑制了涂层进一步腐蚀.在阳极电位下,涂层的摩擦系数随着加载电位的增加显著降低.随着加载电位的升高,涂层的磨损量也相应地增大.在阳极电位0.5 V下的磨损量是阴极电位–1 V下的2.99倍.在0 V时,磨损促进腐蚀的损失量,约占总损失量的13.71%.在–1 V,–0.5 V,–0.25 V,OCP,0 V下的磨损机理主要为磨粒磨损和塑性变形,而在0.25 V,0.5 V下的磨损机理主要为疲劳点蚀.     

石墨烯/碳纳米管增强氧化铝陶瓷涂层的制备及摩擦学性能的研究

对碳纳米管进行混杂功能化处理,并与石墨烯,氧化铝按一定配比制成骨料,与胶黏剂混合充分,采用手工涂覆,低温固化的方法在304不锈钢表面制备复合陶瓷涂层.对混杂碳纳米管分子组成进行了表征;对涂层的微观结构,石墨烯和碳纳米管的分散性,涂层的显微硬度、断裂韧性、涂层与基体的结合强度及摩擦学性能进行了分析.结果表明:混杂处理的碳纳米管表面既接枝了活性基团同时也包覆了表面活性剂,复合涂层结构致密,石墨烯和混杂处理的碳纳米管均匀分散在涂层中,且复合涂层的硬度、断裂韧性、结合强度和耐磨减摩性能明显提高.     

重庆地区露天石刻早期封护材料老化产物及其影响研究

重庆市市委会办公大楼旧址前有一组露天存放的清代砂岩石狮子,表面覆盖着黑色硬壳状物质, 发生大面积脱落,起翘和卷曲。为了揭示黑色硬壳状结构组成,研究其形成过程及对文物产生的影响,利用环境扫描电子显微镜(SEM),X-射线衍射仪(XRD),X-射线荧光光谱仪(XRF),傅里叶变换红外光谱仪(FTIR)和X-射线光电子能谱(XPS)对黑色硬壳及文物表层砂岩样品进行了检测分析研究。结果发现：黑色硬壳断面Mapping元素分布图显示其分为底漆层,中间层和表层,系石刻早期封护层的老化产物;中间层含有立德粉(硫化锌和硫酸钡),黑色外观源于表层中含铅颜料(铅白)变色形成黑色硫化铅及树脂碳化所致;红外光谱与光电子能谱显示出黑色硬壳中含有强的羟基(-OH)特征峰,说明封护层中有机物老化后形成了大量羟基,从而增强了自身亲水性,造成易吸水溶胀与干燥收缩情况,导致大面积脱落,起翘和卷曲现象;黑色硬壳起翘和卷曲部位与下层石刻表面之间形成了易于积水的微空隙,能够聚集雨水中的有害物质,造成石刻表层岩石发生腐蚀,例如黑色硬壳背面及下层岩石表面中高含量硬石膏(CaSO₄),经生水化作用后转化为石膏(CaSO₄·2H₂O),发生体积膨胀造成岩石表面松动和酥粉。因此,当露天文物表面上封护层已老化时,及时地进行清除是十分必要的。     

一体化教学模式在涂料配方设计课程中的应用

介绍了高职背景下涂料配方设计课程的开展过程。采用一体化教学模式,从高职学生的特点入手剖析课程,使用课堂讨论、引发、对比等多种教学方法,使涂料配方设计课程的讲授取得了更好的教学效果。