XPS characterization of wood chemical composition after heat‐treatment

XPS was used to characterize the chemical changes occurring after drying or applying a heat‐treatment to beech wood samples. Our results indicate that the surface of this air‐exposed material could be strongly affected either by the ambient atmosphere during storage or by the complex atmosphere in the oven during drying or heat‐treatment. However, the O/C ratio measured after removal of a thin slice of a few millimetres of an untreated sample is in reasonable agreement with that calculated from the well‐established chemical composition of beech. Through this methodology (equivalent to scraping for hard materials) it is expected to get a realistic characterization of the wood. The reliability and repeatability of the XPS measurements have been checked and the method applied to the study of the chemical changes of the beech samples subjected to heat‐treatment. Heating at 240 °C induces a significant decrease of the O/C ratio from 0.55 before to 0.44 after the treatment. Heat‐treatment induces also a decrease of the C₂ carbon contribution (carbon atom bound to a single non‐carbonyl oxygen) associated with an increase of the C₁ carbon contribution (carbon atoms bound only to carbon or hydrogen atoms), in agreement with chemical modifications reported previously in the literature. Thanks to the small analysed area of the equipment used in this study, different spots were analysed to demonstrate the presence or absence of a gradient of chemical composition due to thermal degradation or migration of extractives from within the wood structure to its surface. At the scale of our observations, the different wood samples investigated (dried or heat treated) appear to be homogeneous. Copyright © 2006 John Wiley & Sons, Ltd.     

Influence of the aggregation state in solution on the supramolecular organization of adsorbed type I collagen layers

In the last years, adsorbed collagen was shown to form layers with a supramolecular organization depending on the substrate surface properties and on the preparation procedure. If the concentration of collagen and the duration of adsorption are sufficient, fibrillar collagen structures are formed, corresponding to assemblies of a few molecules. This occurs more readily on hydrophobic compared to hydrophilic surfaces. This study aims at understanding the origin of such fibrillar structures and in particular at determining whether they result from the deposition of fibrils formed in solution or from the building of assemblies at the interface. Therefore, type I collagen solutions with an increasing degree of aggregation were prepared, using the “neutral-start” approach, by ageing pH 5.8 solutions at 37 °C for 15 min, 2 or 7 days. The obtained solutions were used to investigate the influence of collagen aggregation in solution on the supramolecular organization of adsorbed collagen layers, which was characterized by X-ray photoelectron spectroscopy and atomic force microscopy. Polystyrene and plasma-oxidized polystyrene were chosen as substrates for the adsorption. The size and the density of collagen fibrils at the interface decreased upon increasing the degree of aggregation of collagen in solution. This is explained by a competitive adsorption process between monomers and aggregates of the solution, turning at the advantage of the monomers. More aggregated solutions, which are thus depleted in free monomers, behave like less concentrated solutions, i.e. lead to a lower adsorbed amount and less fibril formation at the interface. This study shows that the supramolecular fibrils observed in adsorbed collagen layers, especially on hydrophobic substrates, are not formed in the solution, prior to adsorption, but are built at the interface, through the assembly of free segments of adsorbed molecules.     

Low‐energy ion scattering: Determining overlayer thickness for functionalized gold nanoparticles

With the widespread use of engineered nanoparticles for biomedical applications, detailed surface characterization is essential for ensuring reproducibility and the quality/suitability of the surface chemistry to the task at hand. One important surface property to be quantified is the overlayer thickness of self‐assembled monolayer (SAM) functionalized nanoparticles, as this information provides insight into SAM ordering and assembly. We demonstrate the application of high sensitivity low‐energy ion scattering (HS‐LEIS) as a new analytical method for the fast thickness characterization of SAM functionalized gold nanoparticles (AuNPs). HS‐LEIS demonstrates that a complete SAM is formed on 16‐mercaptohexadecanoic acid (C16COOH) functionalized 14 nm AuNPs. HS‐LEIS also experimentally provides SAM thickness values that are in good agreement with previously reported results from simulated electron spectra for surface analysis of X‐ray photoelectron spectroscopy data. These results indicate HS‐LEIS is a valuable surface analytical method for the characterization of SAM functionalized nanomaterials. Copyright © 2013 John Wiley & Sons, Ltd.     

Chiralization in mesogenic 1,3-diacylaminobenzenes

The effect of molecular chirality in thermotropic mesomorphic H-bonded polymeric systems has not really been investigated so far. Therefore, five new chiral mesogenic diamides have been prepared and described. Besides more ordered mesophases, the enantiomers exhibit a chiral nematic polymorphism detected by microcalorimetry and probably corresponding to different modes of chiral coiling to give these singular twisted nematic phases.     

La distribution on the crater surface of W-1%La2O3 produced by a single laser pulse

The W-1%La₂O₃ alloy has been irradiated by a single laser pulse (λ = 1064 nm) to simulate transient thermal loads of high energy occurring in a tokamak under operative conditions. A zone with a diameter of ~2 mm, namely, much larger than the focal spot, results to be affected by the pulse, and a crater of about 300 μm is observed in its center. La₂O₃ particles are not present inside the crater. The change of surface morphology is accompanied by elemental redistribution. Multipoint XPS analysis evidenced that the concentration of La is very low in the crater and increases moving toward the border of the affected zone while that of W shows an opposite trend. The composition changes involve only the outmost 5 nm of the sample: through depth profiling, no differences of chemical composition were detected deeper in the alloy between the center and external border of the affected area.     

Low-temperature formation and characterization of Cu2O nanoparticles in the binary gold alloys

Thermal analyses, using differential scanning calorimetry (DSC) and dilatometry, reveal an important anomaly at low temperature for Au-25 wt.% Cu composition after homogenization at 700°C during 2 hours under vacuum followed by heating up to 160°C before water quenching. This anomaly has been already observed and not explained. Surface characterization, using scanning electron microscopy (SEM), atomic force microscopy (AFM), and scanning tunneling microscopy (STM), exhibits a specific topography, consisting of a nanostructured surface. The precipitates of nanostructured particles are homogeneously scattered all over the surface for this 18-carat gold alloy. Moreover, X-ray photoelectron spectroscopy (XPS) shows that the composition of the observed particles corresponds to cuprous oxide phase (Cu₂O). The formation of such material can be explained by the diffusion of copper atoms from the lattice to the surface at 160°C. Pulsed radio-frequency glow discharge optical emission spectroscopy (RF GD-OES) further proves the proposed Cu₂O formation through a diffusion process. The appearance of such cuprous oxide nanoparticles on the Au-Cu alloy surface explains the low-temperature DSC and dilatometry anomaly and affects directly the surface electrical resistance at low temperature. These results might open a large gate for new ideas to investigate in catalytic, electronic, and antimicrobial activities.     

Adsorption of heavy metals by layered double hydroxides grown in situ on Al foam

We investigated the adsorption of heavy metal ions on a nanostructured coating of zinc-aluminum layered double hydroxides (Zn-Al LDHs) grown on aluminum foam by one-step hydrothermal process. This approach aimed to increase the interactive surface and provide a more practical medium for removal of toxic heavy metals from aqueous media. The foam coated with LDH was characterized by using scanning electron microscopy and X-ray diffraction. After immersion in a copper-rich water solution, X-ray photoelectron spectroscopy demonstrated the occurrence of adsorbed copper on the LDH-coated foam with two oxidation states: particles of metallic copper Cu⁰ with oxidized surface Cu⁺¹. X-ray diffraction showed the presence of Cu⁺² in the LDH structure.     

Observation of unusual Griffith’s phase behavior in quadruple perovskite oxide CaCu3Mn4O12 (CCMO) synthesized through chemical route

The CaCu₃Mn₄O₁₂ (CCMO) ceramic was successfully synthesized through the chemical route. The phase formation was confirmed by the X-ray diffraction pattern. Thermogravimetric (TGA), FT-IR, SEM, TEM, EDX, and XPS analysis were performed for investigation of the thermal behavior, phase identification, microstructural analysis, elemental analysis and oxidation state of the CCMO ceramic respectively. FT-IR spectra confirmed the existence of MnO₆ octahedral in body-centered cubic (BCC) complex perovskite oxide that resembles the CaCu₃Ti₄O₁₂ structure. The average particle size was observed by TEM in the range between 100 and 200 nm. AFM shows the average roughness of the surface was found to be in the range of 30 ± 5 nm. XPS and EDX studies confirmed the purity and oxidation state of the CCMO ceramic. The synthesized material shows very interesting unique Griffith’s phase (T_G) results that arise disorder in magnetic susceptibility in which ferromagnetic transition was to be observed in the paramagnetic region.     

Comparative XPS study between experimentally and naturally weathered pyrites

A comparative study has been carried out between experimentally and naturally weathered pyrites. Both were found to share similar species of weathering products and a similar weathering mechanism. The weathering products could be divided into sulphur-bearing or iron-bearing groups. The sulphur-bearing group was comprised of sulphate, sulphite, thiosulphate, elemental sulphur, polysulphide, and mono-sulphide. The iron-bearing group was comprised of goethite, hematite or magnetite, and iron sulphate. The weathering structural profile was also similar for both types of weathering, being composed of a surficial layer and a transitional layer. The surficial layer was made up of both the sulphur-bearing and the iron-bearing products, while the transitional layer was comprised of goethite, and hematite or magnetite. The inward migration of the weathering interface was stimulated by the diffusion of oxygen and moisture. The oxygen was considered to preferably squeeze the iron to form goethite, and the ferric ions of goethite to have acted as a bridge for electron transfer between the oxygen and bulk S₂²⁻ and Fe²⁺ of pyrite.     

Adsorption of amino acids on indium arsenide (1 0 0) surfaces: Assessment of passivation capabilities

Angle-Resolved X-ray Photoelectron Spectroscopy (ARXPS) was used to examine amino acid bonding and oxide removal on InAs(1 0 0) surfaces. Five amino acids were studied, including cysteine, lysine, aspartic acid, glutamic acid and arginine. Observations on the ability of specific functional groups to prevent oxide formation were made by examining the thickness of oxide films on the functionalize surfaces. Amino acids that possessed more than one functional group having resonance were shown to most effectively affect oxide formation. The influence of these groups on the electronic structure of InAs(1 0 0) provides insight into how multifunctional passivation strategies could be beneficial, as well as showing how biological molecules might affect detection when InAs(1 0 0) is used as a platform.