Influence of the e-beam irradiation and photo-oxidation aging on the structure and properties of LDPE-OMMT nanocomposite films

In this paper two systems, polyethylene (LDPE) and polyethylene/commercial organo-modified montmorillonite (LDPE/OMMT) nanocomposite, were subjected to e-beam irradiation at different doses and both the molecular modifications and mechanical properties have been investigated through solubility, FT-IR, calorimetric and tensile tests. Moreover, in some of the irradiated systems photo-oxidation aging was performed and its effects were studied. The results show an enhancement with irradiation of the positive effect of the nano-filler loading, related to the increase of the mechanical properties, due to the increase of the nano-filler polymer interaction.Nevertheless calorimetric and FT-IR data indicate that the well known reduction of LDPE/OMMT nanocomposite resistance to photo-oxidation ageing, with respect to LDPE, is amplified by ionizing radiation.     

基于Cu/SiO_x/Al结构的阻变存储器多值特性及机理的研究

采用氧化硅材料构建了Cu/SiOx/Al的三明治结构阻变存储器件.用半导体参数分析仪对其阻变特性进行测量,结果表明其具有明显的阻变特性,并且通过调节限制电流,得到了四个稳定的阻态,各相邻阻态的电阻比大于10,并且具有良好的数据保持能力.在不同温度条件下对各个阻态进行电学测试及拟合,明确了不同阻态的电子传输机理不尽相同:阻态1和阻态2为欧姆传导机制,阻态3为P-F(Pool-Frenkel)发射机制,阻态4为肖特基发射机制.根据电子传输机制,建立了铜细丝导电模型并对Cu/SiOx/Al阻变存储器件各个阻态的电致阻变机制进行解释.     

退火工艺对ICF靶用冷轧镍膜的影响

 为了满足惯性约束聚变（ICF）和状态方程（EOS）实验以及靶装配工艺的需要,在薄膜轧制过程中间以及轧制工艺完成以后需要对镍膜进行热处理来改善其组织结构和力学性能。对多辊轧机冷轧的方法制备的厚11 mm镍膜中间退火工艺进行了研究,根据确定的合适的退火工艺退火后继续轧制得到成品镍膜厚7 mm,表面粗糙度小于50 nm,基本满足目前状态方程实验对箔膜的要求。金相显微照片表明镍膜晶粒经500 ℃保温1 h退火由轧制前的条带状变为等轴晶;镍膜硬度经500 ℃退火后由4 GPa降低到了2.3 GPa左右;XRD衍射测试表明镍膜经500 ℃以上温度退火后,高角度的衍射峰开始出现,织构得到一定程度的改善。由此可以确定镍膜合适的中间退火温度为520 ℃保温1 h。     

硼膜制备工艺、微观结构及其在硼化镁超导约瑟夫森结中的应用

MgB_2材料具备临界转变温度较高、相干长度大、临界电流和临界磁场高等优点,被认为有替代Nb基超导材料的潜力.研究了不同温度下以化学气相沉积法制备的硼(B)薄膜的微观结构.实验结果表明:较低温度沉积的B先驱薄膜为无定形B膜,可以与Mg蒸气反应生成MgB_2超导薄膜;当沉积温度高于550?C时,所得硼薄膜为晶型薄膜;以晶型硼薄膜为先驱膜在镁蒸气中退火,不能生成硼化镁超导薄膜.利用晶型B膜的这一特点,成功制备了以晶型硼薄膜为介质层的硼化镁超导约瑟夫森结.     

薄膜介质层绕式Blumlein线理论与实验研究

对薄膜介质层绕式Blumlein线的特性参数进行了理论分析。采用Pspice软件对电路模型进行了计算,分析了开关电感、寄生电阻对负载输出波形的影响。结果表明:开关电感的存在使得负载波形前沿变缓,后延波形扭曲变差,寄生电阻会影响负载的电压输出效率。采用模拟软件对传输线中的电磁场分布进行了计算,结果表明薄电极边缘场畸变以及折叠弯曲部分的场变化是绝缘介质耐压必须考虑的因素。基于此理论分析,设计制作了一种新型薄膜介质Blumlein线,绝缘材料为聚酯薄膜,单层薄膜厚100μm,电极为厚50μm的铜皮,单元模块设计耐压50 kV。进行了三级模块串联叠加实验,充电25 kV,匹配负载输出60 kV,脉冲上升沿80 ns,脉冲宽度200 ns。     

离子束增强沉积VO2多晶薄膜的温度系数

用改进的离子束增强沉积方法和恰当的退火从V2O5粉末直接制备了VO2多晶薄膜.实验测试表明，薄膜的取向单一、相变特性显著、结构致密、界面结合牢固、工艺性能良好，薄膜的电阻温度系数（TCR）最高可达4.23%/K.从成膜机理出发，较详细地讨论了离子束增强沉积 VO2多晶薄膜的TCR高于VOx薄膜的TCR的原因.分析认为，单一取向的VO2结构使薄膜晶粒具有较高的电导激活能，致密的薄膜结构减少了氧空位和晶界宽度，使离子束增强沉积 VO2多晶薄膜结构比其他方法制备的VOx薄膜更接近于单晶VO2是其具有高TCR的原 关键词： VO2多晶薄膜 离子束增强沉积 热电阻温度系数     

Electrochemical sensors of heavy metals using novel polymer-modified glassy carbon electrodes

Electroanalytical determination of heavy metals using stripping voltammetry is commonly employed and has many advantages over other methods. The sensitivity of the technique is greatly improved by employing different modified electrodes. Seven novel polymer-modified glassy carbon electrodes have been developed in this investigation for the trace analysis of heavy metals such as zinc, cadmium, lead, arsenic, and copper in formulated samples of waters by square wave stripping voltammetry. Very good responses have been observed for all the metals, while all the modified electrodes employed. The poly(3,4-ethylenedioxythiophene)-modified electrode has resulted in very low limit of detection (LOD) value. Comparison is made between literature results of LOD and the results obtained in this study. An independent atomic absorption spectroscopic analysis of the industrial wastewater sample was carried out and the results compared. The suitability of the method for practical application was ascertained by applying the procedure for the wastewater from a plating industry.     

Influence of surface and bulk layers on the crossover features for interaction parameters of a ferroelectric thin film

The phase diagram of a ferroelectric thin film is studied by using the usual mean-field approximation. The crossover features, from the ferroelectric-dominant phase diagram to the paraelectric-dominant phase diagram, for the physical parameters of the thin film are discussed. Special attention is devoted to the investigation of surface and bulk layers, and how to influence the crossover values of exchange interactions and transverse fields.     

Polarization phase-shifting interferometer by rotating azo-polymer film with photo-induced optical anisotropy

A new type of phase-shifting interferometer was presented by rotating an azo-polymer film with photo-induced optical anisotropy in the light path of orthogonal polarization interferometry. By changing the angle of the optical axis of the azo-polymer film, four phase-shifted fringe patterns were obtained, from which phase difference between orthogonal polarized light could be calculated. The polarization states and the formation of the interferograms were analyzed theoretically using Jones matrix calculations and the experimental verification of the proposed method was also given. This method has a simple optical configuration which utilizes commercially available polarization devices and anisotropic azo-polymer film of low cost. The phase-shifting interferometer also demonstrates a new application of azo-polymer film.     

Use of Mercury Film Glassy Carbon Electrode Modified with Multiwalled Carbon Nanotubes in Electrochemical Analysis of DNA

Mercury film plated on a glassy carbon electrode modified with multiwalled carbon nanotubes (MF/MWNTs/GCE) was used for the analysis of single (ss) and double stranded (ds) DNA, as well as for Jurkat genomic DNAs methylated to different degrees. The results indicated that the DNA molecules adsorbed quite strongly on the MF/MWNTs/GCE surface allowing ex situ adsorption and produce well developed peaks (due to cytosine and adenine) by using adsorptive stripping (Ads, ex situ) square wave voltammetry (SWV). Also, SWV of Jurkat DNA mixtures methylated to different degrees revealed a linear decrease of the peak height with increasing methylation indicating an increase of structural rigidity.