Electrooxidation Mechanism of Methanol at Pt-Ru Catalyst Modified GC Electrode in Electrolytes with Different pH Using Electrochemical and SERS Techniques

The electrochemical and in-situ surface-enhanced Raman spectroscopy （SERS） techniques were used to investigate the electrooxidation behavior of methanol in acidic, neutral and alkaline media at a Pt-Ru nanoparticle modified glassy carbon （Pt-Ru/GC） electrode. The results showed that methanol could be dissociated spontaneously at the Pt-Ru/GC electrode to produce a strongly adsorbed intermediate, CO. It was found that CO could be oxidized more easily in the alkaline medium than in the acidic and neutral media. The peak potential of methanol oxidation was shifted from 0.663 and 0.708 V in the acidic and neutral media to -0.030 V in the alkaline medium, which is due to that the adsorption strength of CO on the Pt surface in the alkaline medium is weaker than that in the acidic and neutral media. The final product of the methanol oxidation is CO2. However, in the alkaline medium, CO2 produced would form CO3^2- and HCO3^- resulting in the decrease in the alkaline concentration and then in the decrease in the performance of DMFC. Therefore, the performance of the alkaline DMFC is not Stable.     

Amperometric Determination of lndole-3-acetic Acid Based on Platinum Nanowires and Carbon Nanotubes

Platinum nanowire （PtNW） can be grown by electrodeposition in polycarbonate membrane, with the average diameter of the nanowires about 250 nm. The PtNW and multiwalled carbon nanotubes （CNT） are then dispersed into chitosan （CHIT） solution. The resulting PtNW-CNT-CHIT material brings new capabilities for electrochemical devices by using the synergistic action of the electrocatalytic activity of PtNW and CNT. By dropping the PtNW-CNT-CHIT film onto the glassy carbon （GO） electrode surface, and after evaporation an amperometric sensor for the determination of indole-3-acetic acid （IAA） was developed. The oxidation current of IAA increased significantly at the PtNW-CNT-CHIT film coated GC electrode, in contrast to that at the CNT-CHIT modified GC. The linear response of the sensor is from 50 ng/ml to 50 μg/ml with a detection limit of 25 ng/mL.     

掺杂对CeO2结构及性能的影响研究进展

纳米CeO2具有比表面积大,储氧性能好,负载金属分散度高等许多优良特性,掺杂对CeO2的结构及性能又有进一步改善,因而是目前研究的热点。本文综述了掺杂对CeO2结构的影响,掺杂对CeO2在催化剂方面的应用研究,以及作为阳极材料的研究进展。展望了掺杂对改进CeO2性能的研究方向。     

等离子体引发原位聚合制备凹凸棒土/聚苯乙烯纳米复合物

用阳离子表面活性剂处理凹凸棒土（Attapulgite),通过超声分散的方法将其均匀分散到苯乙烯单体中，并采用等离子体引发的方法制备出凹凸棒土／聚苯乙烯纳米复合物。通过透射电子显微镜（TEM）和X－射线衍射（XRD）观察了凹凸棒土及其纳米复合物的微观结构。对复合物的GPC测试表明，采用等离子体引发聚合反应可以显著提高树脂的分子量。XRD结果表明聚苯乙烯不是嵌入到凹凸棒土的层间，而是通过离子吸附接枝在凹凸棒土的棒状晶束上。     

溶剂萃取法制备Co(PO_3)_2超细微粉

本文用溶剂萃取法成功地制备了偏磷酸钴超细微粉并通过ＸＲＤ，ＩＲ，ＴＧ，ＤＴＡ，ＴＥＭ等实验对超细微粉的组成、结构进行了表征。     

微孔分子筛纳米晶的控制合成及其催化应用

纳米分子筛因具有高的外表面积和短的孔道结构而显示了独特的催化活性和选择性, 近年来已成为催化界的研究热点.本文就分子筛纳米晶的控制合成、催化基础研究,特别是当前分子筛纳米晶在自组装分级多孔材料和分子筛基纳米复合材料方面的新方向进行了系统的综述,分析了纳米分子筛研究中的机会和应用前景.     

液相合成方形PbS纳米晶的光学特性

采用一种简单、温和的液相合成方法制备了PbS纳米晶，利用透射电镜和高分辨透射电镜对PbS纳米晶的形貌与晶型结构进行了表征．研究了PbS纳米晶的光学吸收和光致发光特性，并比较分析了包覆剂聚乙烯吡咯烷酮(PVP)和回流时间对产物光学特性的影响．结果表明：PVP分子链中的O原子与纳米晶表面吸附的游离态Pb原子形成Pb-O配位键，使产物的激子吸收大为减弱，同时引起了表面浅束缚态能量的升高，最终导致了荧光淬灭现象．     

掺杂镨的纳米二氧化钛光催化降解2,4-二硝基苯酚的研究

以钛酸丁酯为原料,用溶胶-凝胶(sol-gel)法制备了掺杂镨的纳米TiO2粉末.采用X光衍射仪对粉体的物相进行了表征.样品经500 ℃焙烧2 h后,0.5%(摩尔分数)Pr3+-TiO2纳米粉末为单一的锐钛型结构.通过粉体对2,4-二硝基苯酚的降解情况对其光催化活性进行了测试,结果表明与纯TiO2相比,Pr3+-TiO2的光催化活性有较大提高,当Pr3+的掺入量为0.5%(摩尔分数)时催化活性最高.以高压汞灯为光源,2,4-二硝基苯酚的初始浓度为50 mg·L-1,催化剂0.5%(摩尔分数)Pr3+-TiO2投加量为1.0 g·L-1时,2,4-二硝基苯酚的光催化降解效果最好.     

铟锡氧化物纳米网的微波法制备及其光催化特性研究

By using ultrasonic and chemical liquid coprecipitation, the precursor was prepared with high purity In, SnCl₄·5H₂O and urea. The In₂O₃·SnO₂ nanonets were obtained from precursor by heating in microwave oven. The powders were characterized by XRD, TEM. The analyzed results show the sample is In₂O₃·SnO₂, and In₂O₃is rhombohedral system while SnO₂ is tetragonal system. The sample is in spherical grain shape, with average granularity of 35 nm, and the mesh diameter of 10～80 nm. The sample was with fluorescence and good photocatalytic performance for degradation of organic dyestuff.     

纳米结构Bi2Te3化合物的低温湿化学合成

通过对溶液pH值和颜色以及粉末结构的原位分析, 研究了低温湿化学Bi₂Te₃纳米粉末合成过程中的化学和物理反应机制. 结果表明, 碱性添加剂对合成Bi₂Te₃是必要的. 采用65 ℃低温湿化学合成方法, 在添加乙二胺四乙酸二钠(EDTA)的情况下, 制备了Bi₂Te₃纳米囊. 高分辨电镜观察表明, 这种内空管状结构纳米囊的壁厚约为6 nm.