金属锂负极的成核机制与载体修饰

金属锂具有电位低、比容量高等突出优点,是极具吸引力的下一代高能量密度电池的负极材料,然而存在枝晶、死锂、副反应严重、库伦效率低、循环稳定性差等问题,限制了其实际应用。金属锂负极的成核是电化学沉积过程中的重要步骤,锂在集流体或导电载体上的均匀成核和稳定生长对于抑制枝晶死锂、提高充放电效率和循环性能具有关键作用。本文从成核机制与载体效应的角度概述了锂金属负极的研究进展,介绍了锂成核驱动力、异相成核模型、空间电荷模型等内容,分析了锂核尺寸及分布与过电位和电流密度的关系,并通过三维载体分散电流密度、异相晶核/电场诱导成核、晶格匹配等方面的研究实例讨论了载体修饰对锂负极的性能提升。     

2,2-亚甲基-二(4,6-二正丁基苯酚)磷酸钠/凹凸棒土/二氧化硅复合成核剂改性聚丙烯的研究

通过喷雾干燥技术制备了一系列无机纳米粒子(凹凸棒土和/或二氧化硅)与有机磷酸盐类成核剂(NA11)复配的复合成核剂.研究了复合成核剂对聚丙烯力学性能与结晶行为的影响.采用透射电镜(TEM)、扫描电镜(SEM)、偏光显微镜(POM)、广角X射线衍射仪(WAXD)等对复合成核剂在聚丙烯中的分散和对结晶行为的影响进行了表征和分析,并且对复合成核剂改性聚丙烯的机理进行了探讨.结果表明,这种复合成核剂对聚丙烯力学性能的改善明显,聚丙烯的刚性迅速增加,其中三元成核剂对聚丙烯刚性的提高更显著,该成核剂在0.2%用量下对聚丙烯力学性能的改善效果,相当于同等添加量下纯NA11的改性效果.微观形态研究表明三元复合成核剂体系中,三组分形成了相互隔离的分散状态,使有机成核剂和无机纳米粒子可以在聚丙烯基体中实现良好分散.     

How polydispersity of network polymers influences strain-induced crystal nucleation in a rubber

Network polymers in a rubber or a gel often contain non-uniform chain lengths. By means of dynamic Monte Carlo simulations of polymer mixtures with various compositions of two chain lengths, we investigated how the factor of polydispersity influences their strain-induced crystal nucleation. Under a high temperature and a high strain rate, the stretching of both polymers revealed that crystal nucleation is mainly accelerated by the presence of short-chain polymers; nevertheless, both polymers join together in the nucleation process. Further analysis proved that crystal nucleation is initiated from those highly stretched short segments, which are rich on the short-chain polymers.     

基于抛光基材的热蒸镀铜箔生长高平整单层石墨烯薄膜

在石墨烯的化学气相沉积工艺中,铜箔是决定石墨烯薄膜质量的重要因素。传统铜箔由于制备工艺的限制,存在大量的缺陷,导致石墨烯薄膜的成核密度较高。本工作选用抛光铝板、抛光不锈钢板、微晶玻璃和SiO₂/Si作为基材,用热蒸镀法制备了不同粗糙度的铜箔,并详细讨论了以该系列铜箔生长高平整度石墨烯薄膜的条件及铜箔对石墨烯薄膜品质的影响。实验结果表明,铜箔以(111)取向为主,与基材分离后,表面具有纳米级平整度。在生长石墨烯后,从SiO₂/Si剥离的铜箔成核密度是4种基材中最小的。同时,从SiO₂/Si剥离的铜箔晶体结构变化最不明显,具有良好的结晶性,表面几乎不存在铜晶界缺陷。当压强为3 000 Pa,氢气和甲烷流速分别为300 mL/min和0.5 mL/min时,可以获得约1 mm横向尺寸的石墨烯单晶晶畴。     

Influence of Nucleation Agents Concentration on Crystallization Structure and Properties of Glass-ceramics

Deep color glass-ceramics is prepared by using gold tailings as the main raw material, and Cr2O3 is added as nucleation agent. Influence of different Cr2O3 additions on crystallization structure and properties of CaO-MgO-Al2O3-SiO2 glass-ceramics has been discussed so as to select optimum additions. DTA is employed to determine optimum crystallization and nucleation temperatures; XRD and SEM are used to characterize microstructure of each sample; and performance indexes, such as water absorption, bulk density, flexural strength and so on, are also determined. Experimental results show that when 3wt% Cr2O3 is introduced, fine glass-ceramics with diopside as the main crystal and Ca-Fe diopside as the second-crystal is obtained, and its corresponding performance indexes are as follows: water absorption 0.12%, bulk density 2.56 g/cm3, and flexural strength 70.01 Mpa.     

Identification of Different Cobalt Nucleation on Glassy Carbon

The nucleation mechanisms of cobalt from sulfate solutions were studied by utilizing the electrochemical technique, chronoamperometry. It was found that the recorded current-time transients introduced from 1.0mol/L CoSO4 solution were complexes with unusual shapes. All characteristic features were identified as separate process. The instantaneous or progressive nucleation with 2D or 3D growth exists during the cobalt deposition, depending on the applied potentials.     

热历史对聚醚醚酮及其碳纤维复合材料——Ⅱ.熔融行为的影响

本文利用差示扫描量热仪(DSC)研究了聚醚醚酮(PEEK)和以PEEK为基体的碳纤维复合材料(APC-2)的热历史对它们熔融行为的影响。在200—315℃结晶并退火热处理后,试样的DSC曲线上出现了两个吸热峰。低温吸热峰(峰温T′_m)较小,并与结晶和退火温度(T_c)有关;高温吸热峰(峰温T_m)较大,几乎不受T_n的影响。T′_m的出现与在不同T_c下生成的不完整晶体的熔融和重结晶过程有关,而T_m的出现则与完整晶体的熔融过程有关。实验结果表明,T′_m与T_c之间呈线性关系。按文献报道的方法,将T′_m与T_c的直线外推至与T′_m=T_c直线相交,其交点温度即为平衡熔点.结果表明,PEEK和APC-2试样的“平衡熔点”受不同热历史条件下生成晶体的完整程度的影响。当结晶并退火时间越长,求出的“平衡熔点”值越低,并与理论值接近。实验结果还表明,碳纤维表面具有促进PEEK树脂基体晶体完整化的作用,因而导致APC-2试样中PEEK树脂基体的熔点高于纯PEEK树脂。     

成核剂和促进剂对聚对苯二甲酸乙二酯结晶的影响

研究了一种成核剂和结晶促进剂及其混合物对聚对苯二甲酸乙二酯（ＰＥＴ）结晶过程和熔融行为的影响．结果表明,成核剂的引入降低了ＰＥＴ的结晶成核界面自由能,起到促进ＰＥＴ结晶成核的作用,从而加快了ＰＥＴ的结晶速度．而结晶促进剂对ＰＥＴ的结晶速度影响很小,不能促进ＰＥＴ的成核结晶,但能使ＰＥＴ结晶更完善,使ＰＥＴ的结晶度提高．当两者并用时,ＰＥＴ由熔体降温的结晶行为主要由成核剂控制,而成核促进剂的作用不明显．     

沉积温度对Cu_2O薄膜生长过程及光电性能的影响(英文)

以硫酸铜为铜源,采用一步化学浴沉积法制备出了晶粒尺寸可调的纳米晶Cu2O薄膜。通过X射线衍射、扫描电镜和紫外可见分光光度法研究了沉积温度对薄膜晶体结构、成核密度、晶粒尺寸、薄膜厚度和光电性能的影响。结果表明,当在60~90℃范围内调节温度时,能够很好地控制晶粒尺寸、薄膜厚度,并将禁带宽度控制在33~51 nm、392~556 nm和2.47~2.61 eV范围内;随着晶粒尺寸的减小,紫外可见光谱的吸收边有明显的蓝移。此外还对薄膜的生长过程,成核密度和颗粒尺寸变化的机理进行了讨论。     

去氢枞酸类成核剂改性聚丙烯的非等温结晶动力学研究

对以去氢枞酸盐为成核剂的聚丙烯非等温结晶动力学进行了研究，用修正Avrami方程的Jexiorny法和莫志深法进行处理。结果表明：修正Avrami方程的Jeziorny方法和莫志深法都适用于去氢枞酸类成核剂改性的聚丙烯的非等温结晶动力学。在同样的降温速率下纯聚丙烯的t1/2比成核聚丙烯的t1／2要长，当降温速率为20K/min时，纯聚丙烯和成核聚丙烯的t1/2分别为0．78min和0．51min。同时从莫志深法得到的F(T)结果可以看出，达到相同的结晶度时纯聚丙烯所需的降温速率要大于成核聚丙烯所需的降温速率，说明成核剂的加入提高了聚丙烯的结晶速率。从Jeziorny法求出的纯聚丙烯和成核聚丙烯的Avrami指数分别为4．46和2．77，表明成核剂改变了聚丙烯的结晶成核和生长方式。