《高分子化学》课程中“活性自由基聚合”的教学实践

《高分子化学》课程是五大化学基础课程(无机化学、有机化学、分析化学、物理化学、高分子化学)之一,是化学类、高分子材料与工程、材料化学专业的必修课程。"活性"/可控自由基聚合是一种相对较新且重要的聚合物合成技术和方法,针对目前《高分子化学》课程中活性自由基聚合的教学比较薄弱的现状,从教学的角度探讨了活性聚合和可控/"活性"自由基聚合的本质和特点,介绍了本人在这方面的教学实践活动,遵循成果导向教育理念,通过以学为中心的教学方式,打造金课,提高教学质量。     

微波辅助快速制备2D/1D ZnIn2S4/TiO2 S型异质结及其光催化制氢性能

The threat and global concern of energy crises have significantly increased over the last two decades. Because solar light and water are abundant on earth, photocatalytic hydrogen evolution through water splitting has been considered as a promising route to produce green energy. Therefore, semiconductor photocatalysts play a key role in transforming sunlight and water to hydrogen energy. To date, various photocatalysts have been studied. Among them, TiO₂ has been extensively investigated because of its non-toxicity, high chemical stability, controllable morphology, and high photocatalytic activity. In particular, 1D TiO₂ nanofibers (NFs) have attracted increasing attention as effective photocatalysts because of their unique 1D electron transfer pathway, high adsorption capacity, and high photoinduced electron–hole pair transfer capability. However, TiO₂ NFs are considered as an inefficient photocatalyst for the hydrogen evolution reaction (HER) because of their disadvantages such as a large band gap (~3.2 eV) and fast recombination of photoinduced electron–hole pairs. Therefore, the development of a high-performance TiO₂ NF photocatalyst is required for efficient solar light conversion. In recent years, several strategies have been explored to improve the photocatalytic activity of TiO₂ NFs, including coupling with narrow-bandgap semiconductors (such as ZnIn₂S₄). Recently, microwave (MW)-assisted synthesis has been considered as an important strategy for the preparation of photocatalyst semiconductors because of its low cost, environment-friendliness, simplicity, and high reaction rate. Herein, to overcome the above-mentioned limiting properties of TiO₂ NFs, we report a 2D/1D ZnIn₂S₄/TiO₂ S-scheme heterojunction synthesized through a microwave (MW)-assisted process. Herein, the 2D/1D ZnIn₂S₄/TiO₂ S-scheme heterojunction was constructed rapidly by using in situ 2D ZnIn₂S₄nanosheets decorated on 1D TiO₂ NFs. The loading of ZnIn₂S₄ nanoplates on the TiO₂ NFs could be easily controlled by adjusting the molar ratios of ZnIn₂S₄ precursors to TiO₂ NFs. The photocatalytic activity of the as-prepared samples for water splitting under simulated solar light irradiation was assessed. The experimental results showed that the photocatalytic performance of the ZnIn₂S₄/TiO₂ composites was significantly improved, and the obtained ZnIn₂S₄/TiO₂ composites showed increased optical absorption. Under optimal conditions, the highest HER rate of the ZT-0.5 (molar ratio of ZnIn₂S₄/TiO₂= 0.5) sample was 8774 μmol·g^-1·h^-1, which is considerably higher than those of pure TiO₂ NFs (3312 μmol·g^-1·h^-1) and ZnIn₂S₄nanoplates (3114 μmol·g^-1·h^-1) by factors of 2.7 and 2.8, respectively. Based on the experimental data and Mott-Schottky analysis, a possible mechanism for the formation of the S-scheme heterojunction between ZnIn₂S₄ and TiO₂ was proposed to interpret the enhanced HER activity of the ZnIn₂S₄/TiO₂heterojunctionphotocatalysts.      

氢部分选择性催化还原NO反应研究

在低钯含量活性非均布Pd/Al2O3催化剂上，实现了富氧条件下，氢部分选择性催化还原NO过程，低温、富氧条件下NO的转化率高达80％－100％。NO直接分解实验表明，600℃，NO分解转化率在无氧时为17．3％，有0．5％氧存在时接近于0。氢非选择性还原NO条件下，100℃以下，NO转化率为100％。根据实验结果及文献，推测了氢部分选择性还原NO过程中可能存在的反应，不同的反应温度下，NO脱除反应有所不同。在115℃以下，NO还原产物为NH3；115℃－155℃，NO还原产物为NH3、N2O和N2；155℃以上，NO还原产物中无NH3存在。NO还原反应与氢氧反应是平行的竞争反应。     

芥子气模拟剂2-氯乙基乙基硫醚的光催化降解

利用连续流动微反、原位红外和GC/MS等手段考察了芥子气模拟剂2-氯乙基乙基硫醚（2-CEES）在P25 TiO2上的光催化降解反应,证实CO2和H2O是这个反应的最终产物.详细的跟踪分析表明,除了CO2和H2O外,在反应的气相混合物中可检测到C2H4、CH3CHO、CH4、CO、HCl和H2S；少量小分子的羧酸、醚和砜；微量C2H5SC2H5、C2H5S2C2H5、C2H5SC2H4Cl和CH2ClCH2Cl等中间产物;在反应后的催化剂表面可检测到C2H5S2C2H5、C2H5SC2H4OH、C4H9S2C2H5和C2H5S2C2H4OH、等物.根据这些结果提出了2-CEES光催化降解的反应机理,推断2-CEES的光催化降解涉及脱氯、C－S键断裂、有机硫化物光聚合和裂解等复杂过程最终转化为CO2和H2O.认为各种硫物种在表面的积聚引起了催化剂的缓慢失活.     

CuO／CeO2和CuO／Al2O3催化剂的催化性能

本文以ＣＯ氧化为模式反应考察了ＣｅＯ２和Ａｌ２Ｏ３负载氧化铜催化剂的氧化活性，运用ＸＲＤ和ＴＰＲ技术研究了催化剂的还原性能和物相结构，结果表明：载体性质对负载ＣｕＯ催化剂的ＣＯ氧化活性有很大影响，ＣｕＯ／ＣｅＯ２催化剂活性明显高于ＣｕＯ／Ａｌ２Ｏ３催化剂．催化剂的还原特性随载体不同而不同．同时发现，热处理对催化剂铜物种的存在形式，晶粒大小、还原特性及其催化活性有明显影响，ＣｕＯ／Ａｌ２Ｏ３催化剂活性下降的主要因素是生成了活性较低的ＣｕＡｌ２Ｏ４相，而ＣｕＯ／ＣｅＯ２催化剂活性下降是由于ＣｕＯ和ＣｅＯ２发生烧结，晶粒变大     

N-TiO2/ZnO复合纳米管阵列的掺杂机理及其光催化活性

以ZnO纳米柱阵列为模板, 采用溶胶-凝胶法制备出TiO2/ZnO和N掺杂TiO2/ZnO的复合纳米管阵列. 扫描电镜(SEM)、X射线光电子能谱(XPS)和紫外-可见漫反射吸收光谱(UV-Vis)的结果表明: 两种阵列的纳米管均为六角形结构, 直径约为100 nm, 壁厚约为20 nm; 在N-TiO2/ZnO复合纳米管阵列中, 掺入的N离子主要是以N-Ox、N-C和N-N的形式化学吸附在纳米管表面, 仅有少量的N离子以取代式掺杂的方式占据TiO2晶格O的位置; 表面N物种形成的表面态能级和取代式掺杂导致带隙的窄化, 增强了纳米管阵列的光吸收效率, 促进了光生载流子的分离. 光催化实验结果表明, N离子的掺杂有利于N-TiO2/ZnO复合纳米管阵列光催化活性的提高.     

Synthesis and Insulin—sensitizing Activity of a Series of 2—Benzyl—1,3—dicarbonyl Derivatives

A series of 2-benzyl-1,3-dicabonyl derivatives was synthesized.Their insulin-sensitizing activity was evaluated in 3T3-L1 preadipocyte cells.Compounds3,26 and 27 were found to possess strong insulin-sensitizing activity in vitro and were selected for further hypoglycemic evaluation in vivo.     

Sm2O3对CuO-γ-Al2O3催化剂性能的影响

在色谱微反流动法实验装置上考察了负载Ｓｍ２Ｏ３对ＣｕＯγＡｌ２Ｏ３催化剂ＣＯ氧化活性的影响，并运用Ｘ射线衍射（ＸＲＤ）、程序升温还原（ＴＰＲ）及程序升温脱附（ＴＰＤＭＳ）技术研究了Ｓｍ２Ｏ３对ＣｕＯγＡｌ２Ｏ３催化剂的物相结构、氧化还原特性及表面氧的脱附与恢复行为的影响。结果表明，负载适量的Ｓｍ２Ｏ３对ＣｕＯγＡｌ２Ｏ３催化剂表面氧的脱出与恢复有促进作用，可使部分γＡｌ２Ｏ３相变成γＡｌ２Ｏ３和θＡｌ２Ｏ３的混合型。负载适量的Ｓｍ２Ｏ３能改善催化活性，而负载过量的Ｓｍ２Ｏ３则使ＣｕＯ催化剂上ＣｕＯ的晶粒增大，从而对催化活性起了抑制作用。     

连锁聚合反应的动态Monte Carlo模拟及其浓度效应

用动态Monte Carlo方法和键长涨落模型相结合分别对自由基聚合、离子聚合动力学过程进行了计算机模拟, 在三维空间中统计了转化率、聚合度、分子量的数量和重量分布, 并将模拟结果和理论预测进行了对比分析, 同时得到不同浓度下均方回转半径与平均链长的标度关系, 说明三维空间中标度指数与浓度的相关性. 还初步考察了扩散对反应体系分子量的影响. 说明动态Monte Carlo方法用于研究连锁聚合反应动力学过程是有效的, 而且能够同时得到经典的聚合反应Monte Carlo模拟方法所难以得到的链构象、分子扩散等空间相关的信息.     

钕与乌洛托品配合物的合成、表征及抗菌活性研究

报道了配合物NdI3·C6 H1 2 N4 ·HI·13H2 O的新的合成方法 ,通过元素分析、X射线粉末衍射、红外光谱、核磁共振谱、质谱、差热 热重分析 ,确定了配合物的组成和结构 ,9个水分子与Nd3+ 形成配合阳离子 [Nd(H2 O) 9] 3+ ,C6 H1 2 N4 分子以N原子与Nd3+ 直接作用 ,而 3个I- ,HI以及剩余 4个水分子与配合阳离子 [Nd(H2 O) 9] 3+ 以静电引力或氢键的形式作用。首次测定了配体碘化钕、氢碘酸乌洛托品和配合物对枯草芽孢杆菌、大肠杆菌和葡萄球菌的抗菌活性。所有试样对枯草芽孢杆菌的杀死作用较对葡萄球菌、大肠杆菌的杀死作用显著 ,且高浓度溶液(0 .0 5mol·L - 1 )比低浓度溶液 (0 .0 1mol·L - 1 )的抗菌效果好。浓度为 0 .0 5mol·L - 1时 ,由于协同性 ,配合物NdI3·C6 H1 2 N4 ·HI·13H2 O对枯草芽孢杆菌的杀死作用大于相应的配体