LaB6在低压强氮气和氦气中的放电特性

 研究了LaB₆在1~10 Pa氮气和氦气中的直流和脉冲放电特性以及放电过程对电极的影响。结果表明，电极直径为5 mm的LaB6氦气放电管在脉冲工作状态下可以长期稳定放电。在脉冲电压为2.2 kV、脉冲宽度10 ms、频率13.3 Hz下，脉冲峰值放电电流超过120 A。氦气放电管在放电过程中，阴极表面有离子的清洗和活化作用，可以使电极的表面逸出功降低，提高放电管的发射能力和稳定性。LaB₆作为气体放电电极具有寿命长、延迟时间短、放电电流大等优点，可用于重复强流脉冲气体放电的高压高速开关器件。     

气体放电等离子体特性测量I-V曲线不对称性的研究

利用气体放电双探针法研究了等离子体的I-V曲线中的电流I相对于电压V轴交点的不对称性,并提出2种可能的解释:一认为是由于两探针表面积不同引起的;二认为是由于探针所在处等离子体电位不等引起的.本文利用仪器的工艺误差和调换放电管电压的方法,对提出的2种可能原因分别进行验证,并指出第二种解释的合理性,并对其进行了理论分析.     

气体放电击穿过程的物理和数值研究

本文对低气压（１０＾－２Ｐａ）热阴极气体放电的击穿过程给出了物理描述和相应的双流体数学型，并发展了一种选择和调整未知初始条件的有效算法，可以通过伴随试射法得到对初始条件十分敏感的非线性两点边值常微分方程组的数值解，从而给出这类气体放电中击穿过程的定量描述。     

A Scanning Electron Microscopy study of water in soil

Cold stage Scanning Electron Microscopy (SEM) with a rapid cooling technique makes it possible to investigate the water phase within unsaturated porous media. It is thought that this technique preserves the main features of the micromorphology of the water menisci as it exists in the liquid phase in soils. Saddle-shaped elements, as well as pendular rings of water, were observed with concave and convex curvatures of the water-air interface. The hydraulic conductivity of an unsaturated soil may be inferred from SEM photographs. Observations of isolated water menisci indicate the existence of an immobile water domain. The surface geometry of the water menisci was analyzed quantitatively and surface tension and capillary pressure were determined.     

Solubility of carbon dioxide in aqueous solutions of sodium chloride: Experimental results and correlation

The solubility of carbon dioxide in aqueous solutions of sodium chloride was measured in the temperature range from 40 to 160°C, up to 6 mol-kg salt solutions and total pressures up to 10 MPa. Pitzer's⁽¹⁾ equations as well as the Chen and Evans⁽²⁾ model were used to correlate the new data. Results are reported and compared to literature data and correlations.     

Unexpected end‐groups of poly(acrylic acid) prepared by RAFT polymerization

Low‐molecular‐weight poly(acrylic acid) (PAA) was synthesized by reversible addition fragmentation chain transfer polymerization with a trithiocarbonate as chain‐transfer agent (CTA). With a combination of NMR spectroscopy and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, the PAA end‐groups of the polymer were analyzed before and after neutralization by sodium hydroxide. The polymer prior to neutralization is made up of the expected trithiocarbonate chain‐ends and of the H‐terminated chains issued from a reaction of transfer to solvent. After neutralization, the trithiocarbonates are transformed into thiols, disulfides, thiolactones, and additional H‐terminated chains. By quantifying the different end‐groups, it was possible to demonstrate that fragmentation is the rate limiting step in the transfer reaction. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5439–5462, 2004     

A comparative study of the silent discharge treatment of saturated and unsaturated hydrocarbon polymers

Dielectric barrier air discharge treatment of polyethylene, polypropylene, polyisobutylene, polystyrene, and polyisoprene substrates has been characterized by x-ray photoelectron spectroscopy (XPS). The relative reactivities of these polymers towards silent discharge oxidation are rationalized in terms of ozone molecules interacting with an excited surface. © 1994 John Wiley & Sons, Inc.     

示差半微分循环伏安法研究琥珀酰胆碱在水/硝基苯界面的传递行为

研究了油/水界面电解的示差半微分循环伏安行为。在0.01mol/L LiCl(w)-0.01mol/L TBATCIPB(nb)体系“电位窗”比TBATPB(nb)向正方向扩展约50mV,残余电流基本消除,使“电位窗”内的平台向左右拓宽约50mV。算得界面电容约为16μF/cm~2。考察了琥珀酰胆碱离子在w/nb界面的传递伏安特性,结果与一般半微分循环伏安法相似。但峰形改善,检测限降低一个数量级(1×10~(-6)mol/L),相对标准偏差在5％以内,可用于定量测定琥珀酰胆碱。     

Succinic acid adsorption from fermentation broth and regeneration

More than 25 sorbents were tested for uptake of succinic acid from aqueous solutions. The best resins were then tested for successive loading and regeneration using hotwater. The key desired properties for an ideal sorbent are high capacity, complete stable regenerability, and specificity for the product. The best resins have a stable capacity of about 0.06 g of succinic acid/g of resin at moderate concentrations (1–5 g/L) of succinic acid. Several sorbents were tested more exhaustively for uptake of succinic acid and for successive loading and regeneration using hot water. One resin, XUS 40285, has a good stable isotherm capacity, prefers succinate over glucose, and has good capacities at both acidic and neutral pH. Succinic acid was removed from simulated media containing salts, succinic acid, acetic acid, and sugar using a packed column of sorbent resin, XUS 40285. The fermentation byproduct, acetate, was completely separated from succinate. A simple hot water regeneration successfully concentrated succinate from 10 g/L (inlet) to 40–110 g/L in the effluent. If successful, this would lower separation costs by reducing the need for chemicals for the initial purification step. Despie promising initial results of good capacity (0.06 g of succinic/g of sorbent), 70% recovery using hot water, and a recovered concentration of >100 g/L, this regeneration was not stable over 10 cycles in the column. Alternative regeneration schemes using acid and base were examined. Two (XUS 40285 and XFS-40422) showed both good stable capacities for succinic acid over 10 cycles and >95% recovery in a batch operation using a modified extraction procedure combining acid and hot water washes. These resins showed comparable results with actual broth.