Hydrophobicity modification of woven cotton fabric by hydrophobic fumed silica coating

Water repellency of woven cotton fabric was achieved by coating with the aqueous dispersion containing organosilane agent (HDTMS) and fumed silica. The coating agents were applied using padding method and then followed by batching the coated fabric at the ambient temperature for 24 h to allow the condensation reaction between HDTMS silanol group and fumed silica silanol group, rendering silica particles hydrophobic. An ultrasonicator was employed to prepare the homogenous coating dispersion. The water repellency evaluated by water contact angle determination which showed the contact angle over 110° was obtained with low amount of applied HDTMS of 1 wt%. The effect of fumed silica addition on an increase in fiber surface roughness geometry showed the influential result in improving the water contact angle. From durability to washing test, the hydrophobic coatings evidenced from SEM and ATR/FTIR remained adhering to fiber surface, indicating the durability. After washing, the coating on the fabric with fumed silica addition appeared to be scatter particles which made a contribution to the higher contact angle value when compared to sheet-like layer coating in case of HDTMS coating alone.     

Design of a combined ozone/electron beam process for waste water and economic feasibility of the process

A design of a combined ozone/electron beam irradiation process for treating a 50 m³/h waste water stream from a molasses processing is discussed. Moreover, a cost evaluation of such a process in comparison to a conventional ozonation/biology treatment process has been performed to assess the potential of the irradiation process for technical use. Although the result of this comparison is not bad for the irradiation process an implementation into a full scale plant would not seem to be the thing to do in the present case.     

Degradation-fragmentation of marine plastic waste and their environmental implications: A critical review

This review critically evaluates the plastic accumulation challenges and their environmental (primarily) and human (secondarily) impacts. It also emphasizes on their degradation and fragmentation phenomena under marine conditions. In addition, it takes into account the leachability of the various chemical substances (additives) embedded in plastic products to improve their polymeric properties and extend their life. Regardless of their effectiveness in enhancing the polymeric function of plastic products, these additives can potentially contaminate air, soil, food, and water. Several findings have shown that, regardless of their types and sizes, plastics can be degraded and/or fragmented under marine conditions. Therefore, the estimation of fragmentation and degradation rates via a reliable developed model is required to better understand the marine environmental status. The main parameter, which is responsible for initiating the fragmentation of plastics, is sunlight/UV radiation. Yet, UV- radiation alone is not enough to fragment some plastic polymer types under marine conditions, additional factors are needed such as mechanical abrasion. It should be also mentioned that most current studies on plastic degradation and fragmentation centered on the primary stages of degradation. Thus, further studies are needed to better understand these phenomena and to identify their fate and environmental effects.     

Characteristics of major dioxin/furan congeners in melted slag of ash from municipal solid waste incinerators

Polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in slag of fly ash from three municipal solid waste (MSW) incinerators were analyzed to observe any changes in characteristics and distribution of their congeners by melting process. Actual concentration and Toxic Equivalent (TEQ) concentration profiles of 17 major congeners of PCDDs/PCDFs for gas, fly ash and melted slag were compared. The distributions of PCDDs/PCDFs in different streams macroscopically showed similarities with the generally known profiles for emission gas from a municipal waste incinerator. The total concentrations of PCDDs/PCDFs in off-gas and fly ash have been known to be a function of incineration conditions and of air pollution control device utilization; however, their normalized distributions were independent of such conditions. The concentrations of PCDDs/PCDFs in the melted slag of fly ash were not related to the concentrations of PCDDs/PCDFs congeners in fly ash but were rather a function of the melting furnace type and operation. The total amount of PCDDs/PCDFs in the melted slag of fly ash contained almost 150–27,000 times less dioxin than that in fly ash, however, the TEQ of dioxin in the slag was reduced by 435–43,500 times, which could enable them to be utilized as recycled construction materials. In normalized TEQ concentration profiles of 17 congeners of PCDDs/PCDFs, the ratio of PCDFs to PCDDs changed from 1.32 to 2.19 by melting, which showed relatively higher portion of furans left in melted slag than those in fly ash. By comparing reduction ratios of different congeners, PCDDs (dioxins) were relatively easier to destruct than PCDFs (furans) during melting process. The most difficult congener to destruct could be octa-chlorinated dibenzofuran (OCDF) among major congeners. For slag cooling methods, dioxin concentration in TEQ of slow cooled slag by air was four times higher than that of fast cooled slag by water. Thus cooling by water is more appropriate with the added beneficial effect of producing granules/particles, which can be utilized as roadbed materials.     

The Use of Thermogravimetry in the Study of Rubber Devulcanization

Thermogravimetry was employed to study the changes occurring in rubber vulcanizates during devulcanization carried out by microwave treatment, a new promising method of recycling rubber waste. The thermogravimetric parameters T _i , T ₅ and T _p and the compositions of devulcanizates in comparison with vulcanizates were determined. The results obtained allowed estimation of the degree of destruction of the polymer chains in response to microwave treatment and permitted establishment of the most advantageous conditions of devulcanization in order to obtain the best properties of rubber devulcanizates for reuse in rubber processing. The results demonstrated that thermogravimetry is a very useful method for investigation and control of the microwave devulcanization process. This revised version was published online in August 2006 with corrections to the Cover Date.     

Formation enthalpies of rare earth titanate pyrochlores

High-temperature oxide melt solution calorimetry and Rietveld refinements of powder X-ray diffraction data were used to investigate the structure (Fd3m; Z=8) and energetics of a series of RE₂Ti₂O₇ (RE=Sm-Lu) compounds with the pyrochlore structure as well as La₂Ti₂O₇ with a layered perovskite-type structure. All of the RE-titanates were found to be stable in enthalpy with respect to their oxides. In the pyrochlore series, Lu₂Ti₂O₇ was least stable in enthalpy (ΔHf-ox at 298 K=−56.0±4.0 kJ/mol); the most stable materials were Gd-, Eu-, and Sm₂Ti₂O₇ with ΔHf-ox at 298 K=−113.4±2.7, −106.1±4.2, −115.4±4.2 kJ/mol, respectively. In general, as the radius ratio of the A- to B-site cations, R_A/R_B, decreases, the pyrochlore structure becomes less stable. The trend of ionic radius of the RE³⁺ cation vs. ΔHf-ox at 298 K is non-linear and approximately parallels the increasing “resistance” to ion-beam-induced amorphization as R_A/R_B decreases.     

Fast-cycle trace analysis of dioxin in flue gas. Monitoring of the incineration of dioxin-containing waste from seveso

The fast trace analysis method used to monitor 2,3,7,8-TCDD in stack gas during the incineration of the waste from Seveso is described. The sampling of volatile organic compounds from flue gases, distributed between all three aggregation states, is based on a micromethod developed for the trace analysis of water using a specially dimensioned adsorptive charcoal filter (1.5 mg charcoal). In conjunction with subsequent GC/MS measurements the rapid “fast cycle trace analysis” ensured specific 2,3,7,8-TCDD detection down to 100 pg per m³ flue gas in cycle times of about 1–2 hours.     

New Bio-Based Furanic Materials Effectively Absorb Metals from Water and Exert Antimicrobial Activity

Development of sustainable bio-based materials for removal of toxic contaminants from water is a high priority goal. Novel bio-based binary and ternary copolymers with enhanced ion-exchange, adsorption and antibacterial properties were obtained by using plant biomass-derived diallyl esters of furandicarboxylic acid (FDCA) as crosslinking agents and easily available vinyl monomers. The synthesized copolymer materials showed higher sorption capacities for Ni^II, Co^II and Cu^II compared to the commercial ion-exchange resins, and they maintained their high metal adsorption capacities for over 10 cycles of regeneration. The synthesized copolymer gels containing 1–5 wt % of the crosslinker showed excellent water absorption capacities. The synthesized copolymers with 1 % crosslinker content showed swelling ratios high enough to also act as moisture absorbents. Synthesized copolymers with crosslinker content of 10 wt % performed as contact-active antibacterials by inhibiting the growth of Gram-positive (S. aureus) and Gram-negative bacteria (E. coli, K. pneumonia) in suspension tests.     

Layer‐by‐layer deposition of antimicrobial polymers on cellulosic fibers: a new strategy to develop bioactive textiles

In recent years, there has been an increase of infectious diseases caused by different microorganisms and the development of antibiotic resistance. In this way, the search for new and efficient antibacterial materials is imperative. The main polysaccharides currently used in the biomedical and pharmaceutical domains are chitin and its derivative chitosan (CH) and alginates (ALG). In this study, a simple technique of Layer by Layer (LbL) of applying polycation CH and polyanion ALG was used to prepare CH/ALG multilayers on cotton samples via the electrostatic assembly with success. The CH/ALG cotton samples (functionalized) were investigated for their antibacterial properties towards Staphylococcus aureus and Klebsiella pneumonia using the international standard method JIS L 1902:2002. The antibacterial activity of the functionalized samples was tested in terms of bacteriostatic and bactericidal activity, and results showed that the samples exhibited a bacteriostatic effect on the two bacteria tested, as expected. In addition, samples with five layers (CH/ALG/CH/ALG/CH) were more effective in inhibiting bacterial growth. This new coating for cellulosic fibers is a new strategy and may open new avenues for the development of antimicrobial polymers with potential application in health‐care field. Copyright © 2013 John Wiley & Sons, Ltd.     

Evaluation of Formaldehyde in Foundry Waste Sands Using Liquid Chromatography

Abstract

The industrial manufacturing of metallic objects results in a high level of foundry waste sands that may contain toxic compounds such as formaldehyde. The formaldehyde content of foundry waste sands was evaluated by liquid chromatography. Samples were collected during various steps of the industrial processes. Results showed that the phenolic alkaline process generated waste sands with higher formaldehyde content than the furanic process; the highest value was 7.6 × 10^?3% (w/w). In this work, formaldehyde content decreased with time in all of the samples studied, revealing that most formaldehyde was released to the occupational environment.