混合物理化学气相沉积法制备MgB$lt;sub$gt;2$lt;/sub$gt;单晶纳米晶片的研究

利用混合物理化学气相沉积法在石墨衬底上制备出了晶形为六角结构、厚度不同、径向尺寸不一的MgB₂单晶纳米晶片. 利用纳米定向转移技术将此晶片转移到了碳支持膜铜网上, 以便对其精细结构等物性进行表征. 电输运测量和磁性测量结果都表明晶片具有超导电性: T_conset=38 K, T_c(0)=33 K. 扫描电子显微镜图像表明, 晶片表面平整、厚度分布在几个纳米到200 nm之间, 宽度从几微米到上百微米; 高分辨透射电镜图像显示出晶片具有周期性晶格条纹. 选区电子衍射数据与MgB₂已有的单晶衍射数据相符. 这些测量结果证实了其确为高质量单晶MgB₂超导纳米晶片. 本文不仅提出了一种全新的制备单晶MgB₂的方法, 也观察到了纳米尺度MgB₂单晶的零电阻现象, 为后续的磁通钉扎、纳米力学性能等领域的深入研究提供了合适的素材. 关键词： 2')" href="#">单晶MgB₂ 超导纳米晶片 零电阻 混合物理化学气相沉积法     

低能离子束诱导Ag表面纳米金字塔微结构

利用离子束溅射诱导实验方法,在单晶Si(100)基底上辅助沉积银膜,研究了低能Ar+离子束30°入射时,不同离子束能量和束流密度以及基底温度对Ag纳米结构的影响.结果表明:在较低基底温度下(32~100℃)辅助沉积银膜,膜层表面会呈现排列紧密、晶粒尺寸一致的金字塔状纳米结构.当温度升高时(32~200℃),纳米微结构横向尺寸λc迅速增加,而粗糙度先减小(32~100℃)后迅速增大(100~200℃);当离子束能量1 400eV、束流密度15~45μA/cm2时,在相同温度下,随着离子束束流密度的增大,纳米晶粒横向尺寸基本不变,粗糙度略有增加;当离子束流密度为15μA/cm2、能量1 000~1 800eV时,在相同温度下,随着离子束能量的增加,银纳米结构尺寸增加,而表面粗糙度先增加,然后缓慢减小.自组织纳米结构的转变是溅射粗糙化和表面驰豫机制相互作用的结果.     

Structure evolution and stoichiometry control of Pb(Zr, Ti)O3 thick films fabricated by electrospray assisted vapour deposition

Well-crystallized and stoichiometric Pb(Zr, Ti)O₃ (PZT) films, typically ∼5 μm thick, with pure perovskite-type rhombohedral structures have been successfully prepared via an electrospray assisted vapour deposition (ESAVD) method. Control of the deposition temperature within a narrow range of 300-400 °C resulted in films with the most desirable phases. PZT films with close stoichiometric match with the expected composition ratio and uniform element distribution were obtained by adding the appropriate levels of excess Pb in the precursor solutions. The annealed films were uniform, dense, compact and adherent to the substrates. The dielectric constant, ?_r, and loss tangent, tan δ, of the fabricated PZT films measured at 10 kHz were 442 and 0.09, respectively. The ESAVD deposited PZT films showed a remanent polarization, P_r, of 15.3 μC/cm² and coercive field, E_c, of 86.7 kV/cm. These results demonstrate the clear potential of the ESAVD method as a promising technique for the fabrication of thick PZT films.     

Effect of annealing on the nanoscratch behavior of multilayer Si0.8Ge0.2/Si films

In this study, we examined the nanoscratch behavior of annealed multilayered silicon-germanium (SiGe) films comprising alternating sublayers (Si) deposited using an ultrahigh-vacuum chemical vapor deposition (UHV/CVD) system. Annealing consisted of ex situ thermal treatment in a furnace system. We used a nanoscratch technique to investigate the nanotribological behavior of the SiGe films and atomic force microscopy (AFM) to observe deformation phenomena. Our AFM morphological studies of the SiGe films revealed that pile-up phenomena occurred on both sides of each scratch. The scratched surfaces of the SiGe films that had been subjected to various annealing conditions exhibited significantly different features, it is conjectured that cracking dominates in the case of SiGe films while ploughing dominates during the scratching process. We obtained higher coefficients of friction (μ) when the ramped force was set at 6000 μN, rather than 2000 μN, suggesting that annealing of SiGe films leads to higher shear resistance; annealing treatment not only produced misfit dislocations in the form of a significantly wavy sliding surface but also promoted scratching resistance.     

Deposition and wettability of silver nanostructures on Si(1 0 0) substrate based on galvanic displacement reactions

A new route for silver electroless deposition on Si(1 0 0) substrate is developed based on the galvanic displacement process. The basic electroless bath contains NaF and AgNO₃ with different concentrations. The morphologies of electrolessly deposited silver nanostructures, including silver nanowires and nanoparticles, are strongly dependent on the electrolyte composition. Adding an excess dosage of polyvinylpyrrolidone into the basic electrolyte yields final silver films of porous structures composed by multitudinous Ag nanoparticles. The porous silver films possess the surface hydrophobic property after the modification with n-dodecanethiol. Unidirectional wetting and spreading of a water droplet are also demonstrated on the patterned porous Ag films.     

Molecular dynamics and experimental studies on deposition mechanisms of ion beam sputtering

Molecular dynamics (MD) simulation and experimental methods are used to study the deposition mechanism of ionic beam sputtering (IBS), including the effects of incident energy, incident angle and deposition temperature on the growth process of nickel nanofilms. According to the simulation, the results showed that increasing the temperature of substrate decreases the surface roughness, average grain size and density. Increasing the incident angle increases the surface roughness and the average grain size of thin film, while decreasing its density. In addition, increasing the incident energy decreases the surface roughness and the average grain size of thin film, while increasing its density. For the cases of simulation, with the substrate temperature of 500 K, normal incident angle and 14.6 × 10⁻¹⁷ J are appropriate, in order to obtain a smoother surface, a small grain size and a higher density of thin film. From the experimental results, the surface roughness of thin film deposited on the substrates of Si(1 0 0) and indium tin oxide (ITO) decreases with the increasing sputtering power, while the thickness of thin film shows an approximately linear increase with the increase of sputtering power.     

Surface modification of pitch-based spherical activated carbon by CVD of NH3 to improve its adsorption to uric acid

Surface chemistry of pitch-based spherical activated carbon (PSAC) was modified by chemical vapor deposition of NH₃ (NH₃-CVD) to improve the adsorption properties of uric acid. The texture and surface chemistry of PSAC were studied by N₂ adsorption, pH_PZC (point of zero charge), acid-base titration and X-ray photoelectron spectroscopy (XPS). NH₃-CVD has a limited effect on carbon textural characteristics but it significantly changed the surface chemical properties, resulting in positive effects on uric acid adsorption. After modification by NH₃-CVD, large numbers of nitrogen-containing groups (especially valley-N and center-N) are introduced on the surface of PSAC, which is responsible for the increase of pH_PZC, surface basicity and uric acid adsorption capacity. Pseudo-second-order kinetic model can be used to describe the dynamic adsorption of uric acid on PSAC, and the thermodynamic parameters show that the adsorption of uric acid on PSAC is spontaneous, endothermic and irreversible process in nature.     

Electroless deposition of Sno2 and antimony doped SnO2 films

Thin polycrystalline films of SnO₂ and antimony doped SnO₂ have been prepared by simple economic electroless deposition technique. The transmittance in the visible range and the reflectance in the i.r. range for SnO₂ films are ～80% and ～70%, respectively, with resistivity ～10^?2 Ω cm. On the other hand, antimony doped SnO₂ films have transmittance in the visible range and reflectance in the i.r. range, as good as ～86% and ～83%, respectively, with resistivity as low as ～10^?3Ω cm. By vacuum annealing, the resistivity of both types of films has been brought down as low as ～10^?3 and ～10^?4 Ω cm, respectively.     

Influence of deposition pressure on structural, optical and electrical properties of nc-Si:H films deposited by HW-CVD

Hydrogenated nanocrystalline silicon (nc-Si:H) thin films were deposited using HW-CVD technique at various deposition pressures. Characterisation of these films from Raman spectroscopy revealed that nc-Si:H thin films consist of a mixture of two phases, crystalline phase and amorphous phase containing small Si crystals embedded therein. We observed increase in crystallinity in the films with increase in deposition pressure whereas the size of Si nanocrystals was found ∼2 nm over the entire range of deposition pressure studied. The FTIR spectroscopic analysis showed that with increasing deposition pressure the predominant hydrogen bonding in the films shifts from, Si-H to Si-H₂ and (Si-H₂)_n complexes and the hydrogen content in the films was found in the range 6.2-9.3 at% over the entire range of deposition pressure studied. The photo and dark conductivities results also indicate that the films deposited with increasing deposition pressure get structurally modified. It has been found that the optical energy gap range was between 1.72 and 2.1 eV with static refractive index between 2.85 and 3.24. From the present study it has been concluded that the deposition pressure is a key process parameter to induce the crystallinity in the Si:H thin films using HW-CVD.     

Effect of microstructure on thermoelectric properties of CSD-grown Bi2Sr2Co2Oy thin films

Three Bi₂Sr₂Co₂O_y thin films with different microstructures have been prepared by chemical solution deposition on LaAlO₃(001) through varying the annealing temperature. With the decrease in the annealing temperature, both the size and c-axis alignment degree of grains in the film decrease as well, leading to an increase in the film resistivity. In addition, the decrease in the annealing temperature also results in a slight increase in the seebeck coefficient due to the enhanced energy filtering effect of small-grain film. The nanostructured Bi₂Sr₂Co₂O_y film with the average grain size of about 100 nm shows a power factor comparable to that of the films with larger grains. Since the thermal conductivity of the nanostrcutured films can be depressed due to the enhanced phonon scattering by grain boundary, a higher figure of merit is expected in Bi₂Sr₂Co₂O_y thin film with grains in nanometer size.