Effects of oxygen vacancy location on the electronic structure and spin density of Co-doped rutile TiO2 dilute magnetic semiconductors

According to density functional theory （DFT） using the plane wave base and pseudo-potential, we investigate the effects of the specific location of oxygen vacancy （Vo） in a （Ti,Co）06 distorted octahedron on the spin density and magnetic properties of Co-doped rutile Ti02 dilute magnetic semiconductors. Our calculations suggest that the Vo location has a significant influence on the magnetic moment of individual Co cations. In the case where two Co atoms are separated far away from each other, when the Vo is located at the equatorial site of a Co-contained octahedron, the ground state of the two Co cations is d6（t3g↑, t23g ↓） without any magnetic moment. However, if the Vo is located at the apical site, these two Co sites have different ground states and magnetic moments. The spin densities are also observed to be modified by the exchange coupling between the Co cations and the location of Vo. Some positive spin polarization is induced around the adjacent O ions.     

Formation Enthalpy Calculation of Oxygen Vacancy Defect in Doped Lithium Niobate Crystals

The relationship between temperature and oxygen vacancy concentration is deduced in this paper. Based on the data of thermal weight-loss experiment, the formation enthalpies of congruent and several doped LN crystals have been calculated. It was found that the formation enthalpy of oxygen vacancies can be decreased evidently by doping valence-changeable ions. The experimental results were discussed and a new reduction process of the photorefractive LN crystal at a relatively low temperature was proposed, and the reduced crystals showed a good effect in practical use.     

The influence of radiation-induced vacancy on the formation of thin-film of compound layer during a reactive diffusion process

A theoretical approach is developed that describes the formation of a thin-film of AB-compound layer under the influence of radiation-induced vacancy. The AB-compound layer is formed as a result of a chemical reaction between the atomic species of A and B immiscible layers. The two layers are irradiated with a beam of energetic particles and this process leads to several vacant lattice sites creation in both layers due to the displacement of lattice atoms by irradiating particles. A- and B-atoms diffuse via these lattice sites by means of a vacancy mechanism in considerable amount to reaction interfaces A/AB and AB/B. The reaction interfaces increase in thickness as a result of chemical transformation between the diffusing species and surface atoms (near both layers). The compound layer formation occurs in two stages. The first stage begins as an interfacial reaction controlled process, and the second as a diffusion controlled process. The critical thickness and time are determined at a transition point between the two stages. The influence of radiation-induced vacancy on layer thickness, speed of growth, and reaction rate is investigated under irradiation within the framework of the model presented here. The result obtained shows that the layer thickness, speed of growth, and reaction rate increase strongly as the defect generation rate rises in the irradiated layers. It also shows the feasibility of producing a compound layer (especially in near-noble metal silicide considered in this study) at a temperature below their normal formation temperature under the influence of radiation.     

Impact of surface hydroxylation in MgO-/SnO-nanocluster modified TiO2 anatase (101) composites on visible light absorption,charge separation and reducibility

Anatase TiO₂ surfaces, whether oxidised or hydroxylated, can be modified by nanoclusters of SnO and MgO to give a red shift in light absorption, enhanced charge separation and high reducibility.     

Oxygen vacancy O-terminated surface: The most exposed surface of hexagonal WO3 (001) surface

It is known that exposed surface determines material’s performance.WO₃ is widely used in gas sensing and its working surface is proposed to control its sensitivity.However,the working surface,or most exposed surface with detailed surface structure remain unclear.In this paper,DFT calculation confirmed that oxygen vacancy O-terminated surface is the most exposed hexagonal WO₃(001) surface,judging from competitive adsorption of CO and O₂,working surface determinati...     

Suppression of Photoinduced BBO Defects Generation on TIO2（110） by Water

We have investigated creation of variable concentrations of defects on TIO2（110）-（1×1） surface by 266 nm laser using temperature programmed desorption technique. Oxygen-vacancy defects can be easily induced by ultraviolet light, the defects concentration has a linear dependence on power density higher than 50 mW/cm2 for 90 s irradiation. No observation of O2 molecule and Ti atom desorption suggests that UV induced defects creation on TiO2（110）-（1×1） is an effective and gentle method. With pre-dosage of thin films of water, the rate of defects creation on TiO2（110）-（1×1） is slower at least by two orders of magnitude than bare TiO2（110）-（1×1） surface. Further investigations show that water can be more easily desorbed by UV light, and thus desorption of bridging oxygen is depressed.     

不同助剂对CuO-ZnO/SBA-15催化CO_2加氢制甲醇性能影响的研究

以硅质骨架结构介孔分子筛SBA-15为载体,采用浸渍法合成CuO-ZnO/SBA-15(CZ/SBA-15)、CuO-ZnO-MnO_2/SBA-15(CZM/SBA-15)、CuO-ZnO-ZrO_2/SBA-15(CZZ/SBA-15)三组多孔催化剂,在固定床反应器上评价了各组催化剂催化CO_2加氢合成甲醇的性能,同时结合N_2吸附-脱附(BET)、X射线衍射(XRD)、H_2程序升温还原(H_2-TPR)、程序升温脱附(H_2-TPD、CO_2-TPD)、N_2O滴定、X射线光电子能谱(XPS)、透射电子显微镜(TEM)等表征研究了不同助剂对CO_2催化加氢制甲醇的影响。结果表明,催化剂中的金属氧化物改变了SBA-15分子筛载体的孔径大小和比表面积;催化剂CuO-ZnO-MnO_2/SBA-15、CuO-Zn O-ZrO_2/SBA-15中铜的分散度(D_(Cu))和比表面积(A_(Cu))更大,表面CuO粒径更小,更易被还原;相比Mn-O簇,Zr-O簇为增强了碱性位点,提高了甲醇选择性。此外,CuO-ZnO-ZrO_2/SBA-15具有更高的氧空位浓度,催化活性更好,其甲醇选择性为25.02%,与CuO-ZnO/SBA-15、CuO-ZnO-Mn O_2/SBA-15相比分别提高了28%和136.9%,催化效果最好。     

一锅法合成Ce_xZr_(1-x)O_2固溶体催化剂用于热化学循环分解CO_2制CO

采用一锅蒸发诱导自组装法(EISA)制备了一系列不同铈锆物质的量比的铈锆固溶体催化剂,用TGA研究了其热化学循环分解CO_2制CO的催化性能,并采用XRD、Raman光谱、H2-TPR、XPS、SEM和N_2吸附-脱附等手段对催化剂的物相结构、还原性能和表面化学性质进行了表征分析,用热重分析(TGA)研究了铈锆固溶体对热化学循环分解CO_2制CO的催化性能。结果表明,随着Ce/Zr物质的量比增加,铈锆固溶体催化剂的CO_2高温分解活性先增大后减小。Ce/Zr物质的量比为1的Ce_(0.5)Zr_(0.5)O_2催化剂由于具有较多的晶格缺陷和氧空穴,氧迁移能力强,催化活性高,而Ce/Zr物质的量比为3的Ce_(0.75)Zr_(0.25)O_2催化剂具有相对稳定的氧空穴数,循环稳定性好。循环反应后,所有的催化剂均出现了一定程度的烧结,且富锆固溶体发生了相分离,这可能会影响催化剂的性能。     

Study of CO adsorption on perfect and defective pyrite(100)surfaces by density functional theory

First-principles calculations based on density functional theory (DFT) and the generalized gradient approximation (GGA) have been used to study the adsorption of CO molecule on the perfect and defective FeS 2 (100) surfaces. The defective Fe 2 S(100) surfaces are caused by sulfur deficiencies. Slab geometry and periodic boundary conditions are employed with partial relaxations of atom positions in calculations. Two molecular orientations, Cand O-down, at various distinct sites have been considered. Total energy calculations indicated that no matter on perfect or deficient surfaces, the Fe position is relatively more favored than the S site with the predicted binding energies of 120.8 kJ/mol and 140.8 kJ/mol, respectively. Moreover, CO was found to be bound to Fe atom in vertical configuration. The analysis of density of states and vibrational frequencies before and after adsorption showed clear changes of the C–O bond.     

纳米Ce1-xCoxO2-δ固溶体的水热合成及表征

采用水热方法, 在络合剂及氧化剂的辅助下合成出传统方法难以合成的Ce1-xCoxO2-δ固溶体. XRD结果表明, Ce1-xCoxO2-δ固溶体具有立方萤石结构; 产物的平均粒度约为4 nm. 小半径、低价态Co离子的掺杂导致晶格收缩. 结合XRD和Raman表征结果确定固溶体的固溶限约为x=0.06. 紫外光谱分析结果表明, Co离子以混合价态(+2, +3)存在于CeO2晶格中, 随着钴掺杂量的增大, 带隙逐渐蓝移. 低于固溶限样品的室温体相电导率随着钴含量增大而提高.