Raman and Infrared Spectroscopic Characterization of the Phosphate Mineral Lithiophilite—LiMnPO4

Abstract

The metal lithium is very important in industry, including lithium batteries. An important source of lithium besides continental brines is granitic pegmatites as in Australia. Lithiophilite is a lithium and manganese phosphate with chemical formula LiMnPO₄ and forms a solid solution with triphylite, its Fe analog, and belongs to the triphylite group that includes karenwebberite, natrophilite, and sicklerite. The mineral lithiophilite was characterized by chemical analysis and spectroscopic techniques. The chemical is: Li_1.01(Mn_0.60, Fe_0.41, Mg_0.01, Ca_0.01)(PO₄)_0.99 and corresponds to an intermediate member of the triphylite-lithiophilite series, with predominance of the lithiophilite member. The mineral lithiophilite is readily characterized by Raman and infrared spectroscopy.     

EDTA辅助水热法制备性能优异的棒状LiFePO4/C材料

以乙二胺四乙酸为配位剂采用水热法制备了棒状LiFePO₄/C材料。采用X射线衍射、扫描电镜、透射电镜、循环伏安、交流阻抗和恒电流充放电测试等对材料进行表征。结果表明:乙二胺四乙酸对材料的形貌和电性能均有很大影响。通过加入乙二胺四乙酸, 材料的形貌由不规则的颗粒变为棒状的颗粒且颗粒的厚度由140~200 nm减少至40~90 nm, 材料的表面包覆约3.5 nm的均匀碳层, 且该材料极化较小且界面阻抗较低。0.1C放电比容量为167 mAh·g^-1(接近理论容量170 mAh·g^-1)。     

层状钛硅酸盐化合物作为锂离子电池负极储能材料

锂离子二次电池是手提设备的重要电力来源。近年来, 人们为了寻找更新颖更好的锂离子电极材料, 开始研究晶形离子交换材料, 这种材料具有开放孔道, 能够让离子在多孔框架里自由的进出。一种具有层状结构的钛硅酸盐Na-JDF-L1(Na₄Ti₂Si₈O₂₂·4H₂O)经过离子交换后被用作锂离子负极材料。它在循环200次后放电容量保持在364 mAh·g^-1, 并且库伦效率约为100%。通过将TiO₂引入Li(Na)-JDF-L1中, 有效的提高了材料的首次库伦效率和倍率放电性能。     

还原氧化石墨烯/碳纳米管/Co_3O_4三元复合材料的制备与电化学性能

将低温水热反应和低温热处理相结合,制备了含还原氧化石墨烯(RGO)、碳纳米管(CNTs)和Co3O4的三元纳米复合材料RGO-CNTs-Co3O4;利用X射线衍射仪、扫描电子显微镜、透射电子显微镜分析了合成产物的相组成和微观结构,分析了其形成过程;并利用电化学测试装置测定了其作为锂离子电池负极材料的电化学性能.结果表明,在合成反应过程中,氧化石墨烯被还原剂肼还原为石墨烯,同时在石墨烯和CNTs表面生成氢氧化钴;再经低温热处理得到RGO-CNTs-Co3O4三元复合材料.Co3O4纳米颗粒均匀分散在由RGO片层和CNTs组成的三维网络结构中;这种三维网络结构既有利于电子和离子的传输,又能够有效抑制Co3O4在脱嵌锂过程中因体积变化引起的结构破坏.总体而言,合成的新型三元复合材料具有高的比容量以及良好的循环性能与倍率性能.     

Effect of Precursor Drying Process on the Properties of LiFePO4/C Composite with Low Carbon Content

<正>Properties of two LiFePO_4/C composites with low carbon content synthesized from precursors dried by spray drying and blast drying are investigated by scanning electron microscopy, X-ray diffraction, Raman spectroscopy and electrochemical measurements. The two samples have a different morphology and particle size, while the structure of LiFePO_4 is unaffected. The LiFePO_4/C composite prepared from the precursor dried by blast drying has a much lower surface resistance and a much better rate capability because the deposited carbon is more graphite-like and more conductive. The cycling performance is also much better for the LiFePO_4/C composite prepared from the precursor dried by blast drying because only a slight impedance growth is involved upon cycling. These results suggest that the precursor drying process has a significant impact on the properties of LiFePO_4/C composite, and its effect is highly dependent on the carbon content.     

Fast,Reversible Lithium Storage with a Sulfur/Long‐Chain‐Polysulfide Redox Couple

The cathodic reactions in Li–S batteries can be divided into two steps. Firstly, elemental sulfur is transformed into long‐chain polysulfides (S₈?Li₂S₄), which are highly soluble in the electrolyte. Next, long‐chain polysulfides undergo nucleation reaction and convert into solid‐state Li₂S₂ and Li₂S (Li₂S₄?Li₂S) by slow processes. As a result, the second‐step of the electrochemical reaction hinders the high‐rate application of Li–S batteries. In this report, the kinetics of the sulfur/long‐chain‐polysulfide redox couple (theoretical capacity=419 mA h g^?1) are experimentally demonstrated to be very fast in the Li–S system. A Li–S cell with a blended carbon interlayer retains excellent cycle stability and possesses a high percentage of active material utilization over 250 cycles at high C rates. The meso‐/micropores in the interlayer are responsible for accommodating the shuttling polysulfides and offering sufficient electrolyte accessibility. Therefore, utilizing the sulfur/long‐chain polysulfide redox couple with an efficient interlayer configuration in Li–S batteries may be a promising choice for high‐power applications.