基于最大信噪比测量两相流速度

为了克服噪声对信号的影响,提出一种利用最大信噪比和相关法测量两相流速度的方法.基于最大信噪比的信号分离方法是一种盲源信号分离方法,该算法利用统计独立信号完全分离时信噪比最大作为分离准则,它具有非常低的计算复杂度.这里首先利用盲源信号分离方法分别提取出上游和下游两相流信号,并据此求出两相流信号的相关函数曲线,由此求出信号的渡越时间,最后给出仿真实验的处理结果.实验结果表明该方法能够满足两相流速度的测量要求.     

光学多普勒层析三维矢量测速方法研究

光学多普勒层析术(ODT)是一种高分辨、非侵入的生物医学成像手段,能同时得到组织的结构信息和组织内血管的流速信息.提出了一种新型的基于相位分辨技术的ODT三维矢量测速方法.在ODT系统样品臂的准直镜和聚焦透镜之间加入窄带相位片,形成三个不同的相位延迟,通过计算多普勒频移和不同相位延迟下的多普勒展宽,可得到毛细管内的三维矢量流场分布.对已知浓度的聚苯乙烯溶液进行了一系列不同角度和不同流速的实验,结果证明这种新型的ODT矢量测速方法可以较精确的实现三维矢量流速的测量.     

风速分布形状对空调中翅片管蒸发器性能的影响

通过建立空调蒸发器分布参数模型,并对模型进行了验证,进而研究了四种不同风速场对R22和R290翅片管蒸发器流动和换热性能的影响规律。研究表明:在上三角型、下三角型和三角型风速场分布下,蒸发器单位面积换热量、质量流量以及压降均较均匀风速场降低;上三角型较均匀型单位面积换热量下降达7%左右,下三角型和三角型较均匀型下降4%左右;在不同风速场下,各换热温差基本持平,总传热系数起主导作用;R290质量流量均较R22小40%左右,且压降均较R22小24%左右。在满足换热量的要求下,R290在协调压降与质量流量具有一定的优势,可以作为现有空调制冷剂R22的环保型替代工质。     

有限存贮空间内可燃多孔介质流动和传热的研究

对通风条件下可燃多孔介质库房内的流动和传热特性进行了数值模拟,得到了库房有限空间内的温度场和速度场.通过比较不同的来流温度和入口流速,得到的结果表明:可燃多孔介质(弹药)内部发生化学反应并产生热量,其温度由中心向四周逐渐降低;来流流速越大,越有利于弹药的冷却;在来流速度相同的情况下,来流温度越低,越有利于散热,对于可燃多孔介质(弹药)的贮存越安全;在左侧进风口的上下两边以及可燃多孔介质(弹药)的上方,会形成漩涡.     

半导体光放大器超快折射率变化动态特性的研究

建立了分析半导体光放大器（SOA）飞秒量级超快动态特性的数值模型,考虑了增益色散以及群速度色散,能更精确地反映飞秒级超短脉冲经过SOA时的传输特性.基于该模型,可以分析由载流子密度脉动以及载流子加热对折射率变化的影响.同时,也考虑了不同的工作条件以及SOA的结构参数对折射率的影响.理论分析和模拟实验为优化SOA的结构、改善SOA飞秒量级超高速动态特性提供了理论指导. 关键词： 半导体光放大器 折射率动态特性 增益色散 群速度色散     

相干激光雷达中最大似然离散谱峰值估计及Monte Carlo仿真

相干测风激光雷达中一个核心的问题是从微弱的气溶胶后向散射信号中估计出风速。基于零均值复高斯随机过程协方差矩阵统计模型的后向散射信号,首先讨论了最大似然（ML）离散谱峰值（DSP）风速估计算法的克拉美-罗下界（CRLB）与由Fisher信息矩阵论得到的精确CRLB之间的关系。其次,对于ML DSP估计应用于相干测风激光雷达中协方差矩阵统计模型的后向散射信号时,使用计算机Monte Carlo仿真的方法研究了风速估计的概率密度函数。分别讨论了信噪比、激光脉冲累积发数和发射激光脉冲宽度对ML DSP风速估计性能的影响。计算仿真结果表明：ML DSP风速估计的CRLB低于精确的CRLB;在信噪比为－20 dB,100发激光脉冲累积和信噪比为－30 dB,10 000发激光脉冲累积条件下,ML DSP风速估计中坏的估计值所占的比例都为0,好的估计值的标准差分别为0.62 m/s和0.50 m/s。     

强激光加载铝材料动态损伤特性及其微介观结构观测

在神光-Ⅱ装置上利用强激光加载铝材料进行高应变率（高于106 s-1）层裂实验,研究不同初始温度下高纯铝材料的动态损伤特性。采用任意反射面速度干涉仪测量样品自由面速度剖面,由自由面速度剖面计算纯铝样品层裂强度与屈服应力。结果表明:随着温度升高,材料层裂强度减小,屈服应力增大。对激光加载前后样品进行金相分析,观察不同初始温度下纯铝材料的微介观结构变化及其损伤特性。结果表明：随着温度升高,样品晶粒尺度缓慢增大,但在873 K（近熔点）时晶粒尺度急剧增加;层裂面附近小孔洞数目较多,孔洞尺寸也较大,而远离层裂面处,孔洞数目相对较少,且尺寸也较小;材料的断裂方式随温度升高由沿晶断裂为主逐渐变为穿晶断裂为主。     

Ultrasonic technology for enhanced oil recovery from failing oil wells and the equipment for its implemention

A new method for the ultrasonic enhancement of oil recovery from failing wells is described. The technology involves lowering a source of power ultrasound to the bottom of the well either for a short treatment before removal or as a permanent placement for intermittent use. In wells where the permeability is above 20 mD and the porosity is greater than 15% ultrasonic treatment can increase oil production by up to 50% and in some cases even more. For wells of lower permeability and porosity ultrasonic treatment alone is less successful but high production rates can be achieved when ultrasound is applied in conjunction with chemicals. An average productivity increase of nearly 3 fold can be achieved for this type of production well using the combined ultrasound with chemical treatment technology.     

Theoretical analysis of stack gas emission velocity measurement by optical scintillation

Theoretical analysis for an online measurement of the stack gas flow velocity based on the optical scintillation method with a structure of two parallel optical paths is performed. The causes of optical scintillation in a stack are first introduced. Then, the principle of flow velocity measurement and its mathematical expression based on cross correlation of the optical scintillation are presented. The field test results show that the flow velocity measured by the proposed technique in this article is consistent with the value tested by the Pitot tube. It verifies the effectiveness of this method. Finally, by use of the structure function of logarithmic light intensity fluctuations, the theoretical explanation of optical scintillation spec- tral characteristic in low frequency is given. The analysis of the optical scintillation spectrum provides the basis for the measurement of the stack gas flow velocity and particle concentration simultaneously.     

Grüneisen parameter for HCP iron at extreme compression

The Thomas–Fermi approximation gives the Grüneisen parameter γ=γ_∞=1/2 for all materials at extreme compression (P→∞ or V→0). After re-analyzing the existing experimental data of volume dependence of Grüneisen parameter γ of hexagonal close-packed (HCP) iron, we find that γ=1/2+a(V/V ₀)^1/3+b(V/V ₀) ⁿ , where a, b and n are constants. Based on this new form of γ, the second Grüneisen parameter q, the Debye temperature θ_D and the shear sound velocity v _s of HCP iron are discussed in the present work. It is found that the zero pressure second Grüneisen parameter q ₀=0.654, which is consistent with the previously determined value of HCP iron for Earth's core physics from Dubrovinsky et al. The calculations for the Debye temperature and the shear sound velocity are also found to be in good agreement with the experimental data.