石墨炉原子吸收法测定化妆品中的砷

在过氧化氢溶液及硝酸镍存在下，用石墨炉原子吸收法测定化妆品中砷的含量，砷的浓度在0-1mg/L时与吸光度线相关，线性方程为A=0.838c 0.003，相关系数为0.99994。对液体和固体化妆品中的砷进行测定，砷的加标回收率为98.3%-98.7%，测定结果的相对标准偏差为0.65%-1.50%。     

开放式微波消解与干灰化法消解测量食品中铅的方法比较

对开放式微波消解法与干灰化法消解测量食品中铅的方法进行了比较，试验表明，前者操作简易，试验周期短，在测量精度和加标回收率方面两种方法无显著性差别。     

巯基乙酰萘胺极谱行为研究及分析应用 Ⅱ.银(Ⅰ)离子的示波极谱测定

在前文研究的基础上,经试验,证明Ag(Ⅰ)与巯萘剂(TN)反应生成非电活性物质,导致电活性物质DTN电流降低。在最佳条件下,Ag(Ⅰ)浓度在3.7×10~(-8)～4.5×10(-7)mol/L范围内与DTN电流峰高降低值成线性关系,检出限为2.2×10~(-8)mol/L(相当于2.4ng/ml)Ag(Ⅰ)。方法用于纯镍和氢氧化钾中痕最银的测定,结果满意。     

聚异丁烯高活性端基含量及相对分子质量测定方法的研究

综合使用核磁，VPO和近红外光谱分析技术对聚异丁烯活性端基含量以及相对分子质量的测定进行了详细研究，分别建立核测定聚异丁烯活性端基含量以及其他烯键含量和近红外光谱快速测量聚异聚丁烯活性端基含量。其他烯键含量和相对分子质量的分析方法。成对t检验结果表明，近红外光谱分析方法测定结果与核磁和VPO方法测定结果之间无显著性差异。     

空气中水含量的计算及其在色谱分析中的应用

本文介绍了空气中水含量的计算式并编制了空气中的水含量表。实验证明,表上的数据适用于色谱分析。     

Enantioselective separations by capillary GC on derivatized cyclodextrins. Part 2: Determination of enantiomeric excess of some racemic 2,3-isopropylidene-1,2,3-cyclohexanetriol derivatives on permethyl α-, β-, and γ-cyclodextrins

Capillary GC on permethyl α-, β-, and γ-cyclodextrins has been applied to separate and quantify the enantiomers of some 2,3-iso-propylidene-1,2,3-cyclohexanetriol derivatives. Quantitative CGC data are compared to those obtained with chiral shift ¹H NMR.     

Cd-Sn(0.2)-Zn三元合金高压相图的测定

 为了验证三元合金高压相图的计算结果，本文采用高压DTA方法，测定了Cd-Sn-Zn三元系中x_Sn=20 at.%截面的高压垂直截面相图，实验压力为0、0.5、1.0、1.5 GPa。测得的常压相图（p=0 GPa）中其液相线与H. J. Bray的实验结果完全相符，所得高压相图与常压相图比较，在p=1.5 GPa时低共晶点上移了大约35 K，共析组成向富锌端移动了大约8%。     

Effect of carbon content on the microstructure and the cracking susceptibility of Fe-based laser-clad layer

The laser cladding of Fe-based alloys on a medium carbon steel substrate was performed using a CO₂ laser and Ar shielding gas that was blown into a molten pool. The microstructure and cracking susceptibility of the laser-clad layers were studied in terms of carbon additions. Results show that the small change of the carbon content in the alloy powders can obviously change the microstructure and properties of the layers. When the carbon content is in the range of 0.3–0.4 wt.%, the decrease of the carbon content in alloy powders will increase the hardness and toughness of the layers simultaneously under the same process parameters. As a result, crack-free coatings with high hardness can be obtained. As the carbon content increases from 0.2 wt.% to 0.4 wt.%, the segregation ratio of chromium increases, while the segregation ratios of nickel, manganese, and silicon first decrease and then increase. At the same time, a new designing principle concerning the composition and microstructure has been put forward, and the principal mechanisms of strengthening and toughening of the layers are fine-grain strengthening and low carbon martensitic phase transformation strengthening.