La distribution on the crater surface of W-1%La2O3 produced by a single laser pulse

The W-1%La₂O₃ alloy has been irradiated by a single laser pulse (λ = 1064 nm) to simulate transient thermal loads of high energy occurring in a tokamak under operative conditions. A zone with a diameter of ~2 mm, namely, much larger than the focal spot, results to be affected by the pulse, and a crater of about 300 μm is observed in its center. La₂O₃ particles are not present inside the crater. The change of surface morphology is accompanied by elemental redistribution. Multipoint XPS analysis evidenced that the concentration of La is very low in the crater and increases moving toward the border of the affected zone while that of W shows an opposite trend. The composition changes involve only the outmost 5 nm of the sample: through depth profiling, no differences of chemical composition were detected deeper in the alloy between the center and external border of the affected area.     

Experimental and kinetic modeling study of the oxidation of cyclopentane and methylcyclopentane at atmospheric pressure

Cyclopentane and methylcyclopentane oxidation was investigated in a jet-stirred reactor at atmospheric pressure, over temperatures ranging from 900 to 1250 K, for fuel-lean, stoichiometric, and fuel-rich mixtures at a constant residence time of 70 ms. The initial mole fraction of both fuels was kept constant at 1000 ppm. The reactants were highly diluted by a flow of nitrogen to ensure thermal homogeneity. Samples of the reacting mixture were analyzed online and off-line by Fourier transform infrared spectroscopy and gas chromatography. A detailed kinetic mechanism consisting of 590 species involved in 3469 reactions was developed, and simulation results were compared to these new experimental data and previously reported ignition delays. Reaction pathways analysis as well as sensitivity analyses were performed to get insights into the differences observed during the oxidation process of cyclopentane and methylcyclopentane.     

Synthesis of fused indolines by interrupted Fischer indolization in a microfluidic reactor

This study describes our development of a microfluidic reaction scheme for the synthesis of fused indoline ring systems found in several bioactive compounds. We have utilized a continuous-flow microfluidic reactor for the reaction of hydrazines with latent aldehydes through the interrupted Fischer indolization reaction to form fused indoline and azaindoline products. We have identified optimal conditions and evaluated the scope of this microfluidic reaction using various hydrazine and latent aldehyde surrogates. This green chemistry approach can be of general utility to rapidly produce indoline scaffolds and intermediates in a continuous manner.     

Detailed experimental and kinetic modeling study of 3-carene pyrolysis

3-Carene is an important potential biofuel with properties similar to the jet-propellant JP-10. Its thermal decomposition and combustion behavior is to date unknown, which is essential to assess its quality as a fuel. A combined experimental and kinetic modeling study has been conducted to understand the initial decomposition of 3-carene. The pyrolysis of 3-carene was investigated in a jet-stirred quartz reactor at atmospheric pressure, at temperatures varying from 650 to 1050 K, covering the complete conversion range. The decomposition of 3-carene was observed to start around 800 K, and it is almost complete at 970 K. Online gas chromatography shows that primarily aromatics are generated which suggests that 3-carene is not a good fuel candidate. The potential energy surface for the initial decomposition pathways determined by KinBot shows that a hydrogen elimination reaction dominates, giving primarily cara-2,4-diene. Next to this molecular pathway, radical pathways lead to aromatics via ring opening. The kinetic model was automatically generated with Genesys and consists of 2565 species and 9331 reactions. New quantum chemical calculations at the CBS-QB3 level of theory were needed to calculate rate coefficients and thermodynamic properties relevant for the primary decomposition of 3-carene. Both the conversion of 3-carene and the yields of the primary products (ie, benzene and hydrogen gas) are well predicted with this kinetic model. Rate of production analyses shows that the dominant pathways to convert 3-carene are hydrogen elimination reaction and radical chemistry.     

An experimental and modeling study of the oxidation of n-heptane,ethylbenzene, and n-butylbenzene in a jet-stirred reactor at pressures up to 10 bar

In the context of better understanding pollutant formation from internal combustion engines, new experimental speciation data were obtained in a high-pressure jet-stirred reactor for the oxidation of three molecules, which are considered in surrogates of diesel fuel, n-heptane, ethylbenzene, and n-butylbenzene. These experiments were performed at pressures up to 10 bar, at temperatures ranging from 500 to 1 100 K, and for a residence time of 2 s. Based on results previously obtained close to the atmospheric pressure for the same molecules, the pressure effect on fuel conversion and product selectivity was discussed. In addition, for the three fuels, the experimental temperature dependence of species mole fractions was compared with simulations using recent literature models with generally a good agreement. For n-heptane, the obtained experimental data, at 10 bar for stoichiometric mixtures, included the temperature dependence of the mole fractions of the reactants and those of 21 products. Interestingly, the formation of species previously identified as C₇ diones was found significantly enhanced at 10 bar compared with lower pressures. The oxidation of ethyl- and n-butylbenzenes was investigated at 10 bar for equivalence ratios of 0.5, 1, and 2. The obtained experimental data included the temperature dependence of the mole fractions of the reactants and those of 13 products for the C₈ fuels and of 19 products for the C₁₀ one. For ethylbenzene under stoichiometric conditions, the pressure dependence (from 1 to 10 bar) of species mole fraction was also recorded and compared with simulations with more deviations obtained than for temperature dependence. For both aromatic reactants, a flow rate analysis was used to discuss the main pressure influence on product selectivities.     

Efficient monooleoyl glycerol synthesis employing hybrid ultrasonic-infrared-wave promoted reactor: Concurrent catalytic and noncatalytic esterification kinetics

For the first time, intensification of monooleoyl glycerol (MOG) synthesis has been investigated in an ultrasonic-infrared-wave (USIRW) promoted batch reactor. Esterification of octadecanoic acid (ODA) with glycerol (Gl) has been conducted [using Amberlyst 36 wet catalyst] in three different reactors, namely traditional batch reactor (TBR), infrared wave promoted batch reactor (IRWPBR), and USIRW-promoted batch reactor (USIRWPBR) to assess the relative efficacy. The energy-efficient USIRWPBR remarkably intensifies the ODA-Gl esterification as manifested through superior ODA conversion (92.5 ± 1.25%) compared to that achieved in IRWPBR (79.8 ± 1.2%) and TBR (36.39 ± 1.25%). The most favorable reaction condition for optimum ODA conversion and maximum MOG yield was identified through statistical optimization over a selected parametric range, namely 3-5 Gl/ODA mole ratio, 0.004-0.006 g/mL Amberlyst 36 catalyst concentration, 300-700 rpm impeller speed, and 333-353 K reaction temperature. The present study also reports the formulation and validation of an innovative reaction kinetics, that is, concurrent noncatalytic and heterogeneously catalyzed (CNCHC) reaction mechanism in addition to the conventional heterogeneous kinetic models (LH and Eley-Rideal mechanisms). Under combined USIRW, the CNCHC esterification mechanism could best describe ODA-Gl esterification (R² = 0.98) compared to LH (R² = 0.97) and Eley-Rideal (R² = 0.88) mechanisms. The optimal product (MOG) was characterized by differential scanning calorimetry and thermogravimetric analysis to assess its crystallization property and thermal stability for possible application as plasticizer/fuel additives.     

Characterization of the Insoluble Sludge from the Dissolution of Irradiated Fast Breeder Reactor Fuel

Insoluble sludge is generated in the reprocessing of spent fuel. The sludge obtained from the dissolution of irradiated fuel from the “Joyo” experimental fast reactor was analyzed to evaluate its chemical form. The sludge was collected by the filtration of the dissolved fuel solution, and then washed in nitric acid. The yields of the sludge weight were less than 1% of the total fuel weight. The chemical composition of the sludge was analyzed after decomposition by alkaline fusion. Molybdenum, technetium, ruthenium, rhodium, and palladium were found to be the main constituent elements of the sludge. X-ray diffraction patterns of the sludge were attributable to Mo₄Ru₄RhPd, regardless of the experimental conditions. The concentrations of molybdenum and zirconium in the dissolved fast reactor fuel solutions were low, indicating that zirconium molybdate hydrate is produced in negligible amounts in the process.     

A comparison of different approaches to integrate flamelet tables with presumed-shape PDF in flamelet models for turbulent flames

Flamelet models for turbulent combustion modelling make use of presumed-shape probability density functions (PDFs) for integrating laminar flamelet solutions to obtain an integrated flamelet table that can readily be used for turbulent flame calculations. The existence of non-unique approaches for such an integration has rarely been investigated before. For the first time, this work studies systematically the non-uniqueness of the flamelet table integration approaches. A flamelet model called the flamelet/progress variable model is used in the study, although the issue exists generally in many other flamelet models. Two classes of table integration approaches are investigated, one preserving the laminar flamelet structures during integration and the other not. Three different table integration approaches are examined and compared in detail to provide a thorough understanding of the different approaches. A partially stirred reactor is used as a test case for examining the different approaches. A method based on the transported PDF method is also employed to provide a reference for the assessment of the different flamelet table integration approaches. It is found in general that the flamelet preserving integration approach yields a more reasonable joint PDF of the mixture fraction and the progress variable, and the prediction results are closer to the referenced transported PDF results.