同轴电喷法制备PCL-蛋清体系复合微胶囊

以鸡蛋的卵清蛋白作为蛋白质药物模板、生物可降解材料聚己内酯(PCL)为药物载体模板,采用同轴电喷法制备PCL-蛋清体系的复合微球.研究了电导率、黏度对于电喷微球成型的影响.核壳溶液推进速率比、电压、溶液质量分数和接收距离等对于所得微球表面形态和结构的影响.利用扫描电子显微镜(SEM)研究了微球的表面形态,用荧光显微镜表征了微球的包覆模式.结果表明:同轴电喷法可以制备PCL-蛋清体系的复合结构微胶囊,其中推进速率比对微球形貌、粒径及其分布的影响比较明显,当PCL与蛋清溶液推进速率比大于10时,将出现具有包覆结构的微球.     

Initiation of Light Pulses by a Coaxial H‐Compressed Discharge

An optimum configuration of the discharge channel of a coaxial Hcompressed discharge is determined to exclude the screening influence of an envelope on discharge radiation in the UV region of a spectrum. It is shown that the use of an Hcompressed discharge of coaxial shape makes it possible to increase the radiation yield in the UV spectrum as compared to a plane shape at the same parameters of electric power supply.     

Copolymerization of norbornene with methoxycarbonylnorbornene catalyzed by Ni{CF3C(O)CHC[N(naphthyl)]CH3}2/B(C6F5)3 catalytic system and good processability for Dry/Wet phase inversion and electrospinning technique

Copolymerization of norbornene (NB) with methoxycarbonylnorbornene (NB‐COOCH₃) was carried out with catalytic system of Ni{CF₃C(O)CHC[N(naphthyl)]CH₃}₂ and B(C₆F₅)₃ in toluene. The catalytic system exhibited higher activity 2.69 × 10⁵ (gpolymer/mol Ni h) for copolymerization of norbornene and methoxycarbonylnorbornene. The influence results of the comonomer feed content on the polymerization showed that the NB‐COOCH₃ has a very high insertion ratio in all copolymers, and the NB‐COOCH₃ content in copolymers can be controlled to be 7.9–77.6 mol % at content of 10–90 mol % of the NB‐COOCH₃ in the monomer feeds ratios. The reactivity ratios, r_NB‐COOCH3 = 0.578 and r_NB = 0.859, were determined by the Kelen–TÜdÕs method. Copolymers were processed by solution casting method, dry/wet phase inversion technique, and electrospinning. The films prepared by solution casting method showed good transparency in the visible region. The membranes processed by dry/wet phase inversion technique were microporous structures. The fibers diameters fabricated by electrospinning were about 3 μm. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Atmospheric plasma treatment of pre‐electrospinning polymer solution: A feasible method to improve electrospinnability

The electrospinnability of polyethylene oxide (PEO) was manipulated by atmospheric plasma treatment of pre‐electrospinning solutions. Conductivity, viscosity, and surface tension of PEO solutions increased after plasma treatment, and the plasma effect remained longer when the solution concentrate increased. Both untreated and treated solutions were then electrospun, and the morphology of the resultant nanofibers was observed by SEM. Atmospheric plasma treatment improved the electrospinnability of PEO solutions and led to less beads and finer diameter distribution in the resultant nanofibers. Additionally, plasma treatment of the pre‐electrospinning solutions affected the crystal structure of resultant nanofibers. These results suggest that atmospheric plasma treatment is a feasible approach to improve the electrospinnability of polymer solutions and can used to control the structure of electrospun nanofibers. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Morphology and physical properties of a novel Ramie‐PU blended nonwoven by electrospinning: The effect of cosolvent ratio

A novel macro/nano blended nonwoven with excellent physical properties was prepared by electrospinning polyurethane (PU) nanofibers onto the surface of ramie webs under different weight ratios of N,N‐dimethylacetamide (DMAc)/acetone cosolvents. The ratio of cosolvents has a significant influence on the morphology, tensile properties, resilience, and thermal properties of the resultant samples. Bead‐free and fine interconnected nanofibers were obtained with an increase of acetone content up to 60 wt%. The total physical properties of the blended nonwovens were optimal for a DMAc/acetone ratio of 40/60, in which the tensile load at break, extension at break and Young's modulus were 441, 54, and 256% higher than that of pure ramie web, respectively. The resilience of the blended nonwovens was ～20% higher than that of nonblended ramie web. The significant improvement of physical properties may be due to the good connection between PU nanofiber membranes and ramie webs and the molecular chain structure differences, interconnected structural differences, and high extensibility of PU nanofibers, according to the results of crystallization by differential scanning calorimetry (DSC) and morphological observation by scanning electronic microscopy (SEM). © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1–14, 2010     

Preparation of polybenzoxazole fibers via electrospinning and postspun thermal cyclization of polyhydroxyamide

Polybenzoxazole (PBO) fibers with a submicron diameter were successfully prepared by electrospinning its precursor, polyhydroxyamide (PHA), solutions to obtain the PHA fibers first, followed by appropriate thermal treatments for cyclization reaction. BisAPAF‐IC PHA with two different molecular weights (MWs) were synthesized from a low temperature polymerization of 2,2′‐bis(3‐amino‐4‐hydroxyphenyl) hexafluoropropane (BisAPAF) and isophthaloyl chloride (IC). Using dimethylacetamide (DMAc) and tetrahydrofuran (THF), solvent effects on the electrospinnability of PHA solutions were investigated. For balancing the solution properties, it was found that DMAc/THF mixture with a weight ratio of 1/9 was the best cosolvent to prepare smooth PHA fibers; uniform PHA fibers with a diameter of 325–720 nm were obtained by using 20 wt % PHA/(DMAc/THF) solutions. For a fixed PHA concentration, solutions with a lower MW of PHA yielded thinner electrospun fibers under the same electrospinning condition. After obtaining the electrospun BisAPAF‐IC PHA fibers, subsequent thermal cyclization up to 350 °C produced the corresponding thermally stable BisAPAF‐IC PBO fibers with a diameter of 305–645 nm. The structure of the precursor fibers and the fully cyclized fibers were characterized by FTIR. For the cyclized BisAPAF‐IC PBO fibers, thermogravimetric analysis showed a 5% weight loss temperature at 523 °C in nitrogen atmosphere. The interconnected fiber structure in the BisAPAF‐IC PBO fiber mats was irrelevant to the curing process, but resulted from the jet merging during the whipping process as revealed by the high speed camera images. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 8159–8169, 2008     

再谈"三维导体"的自感系数

由公式ε＝Ｌ│ｄＩ／ｄｔ│出发，只要求出“三维导体”中的等效自感电动势，即可求得自感系数Ｌ，并以无限长同轴电缆自感系数的求解为例加以证明。     

Poly(methyl methacrylate)/silica nanocomposite fibers by electrospinning

Uniform poly(methyl methacrylate) (PMMA)/silica nanocomposite fibers containing up to 20 wt % silica were prepared by electrospinning. The electrospun solutions were prepared by mixing a solution of PMMA in dimethyl formamide (DMF) with colloidal silica in methyl ethyl ketone (MEK). The average fiber diameter decreases from 2.49 μm to 1.69 μm when 20 wt % silica is incorporated as a result of considerably increased solution conductivity, although the solution viscosity increases significantly, which should result in opposite effect. Thinner fibers (down to 350 nm) can be obtained by changing DMF/MEK proportion and by the addition of an ammonium salt. Nano‐sized silica particles (10–40 nm) distributes homogeneously in the fibers, as revealed by transmission electron microscopy. Furthermore, the incorporation of silica nanoparticles can change the thermal properties and surface wettability of the fiber mats. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1211–1218, 2009     

Phase morphology and mechanical properties of the electrospun polyoxymethylene/polyurethane blend fiber mats

Polyoxymethylene/thermoplastic polyurethane (POM/TPU) blends containing 10–30 wt % of TPU were electrospun using hexafluoroisopropanol as the solvent. The average fiber diameter increases with the increase in TPU content from 0.68 μm for neat POM fibers to 0.92 μm for POM/TPU 7:3 blend fibers due to the increase in solution viscosity. Core/sheath structure with the major component POM as the core and the minor component TPU as the sheath was observed by transmission electron microscopy and further confirmed by surface N contents of the blend fiber mats. The crystalline melting point and the degree of crystallinity of POM have no obvious change by coelectrospinning with TPU due to lack of interaction between POM and TPU as revealed by Fourier transform infrared spectroscopy. Tensile tests showed that the unusual high ductility of POM fiber mat could be further increased by coelectrospinning with 10 or 20 wt % TPU without significantly decreasing the stiffness and strength. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1853–1859, 2009