轴流风扇叶片端导叶作用的研究

本文采用数值方法研究了叶片端导叶对轴流风扇性能的影响。通过与普通开式轴流风扇比较,分析了叶片端导叶对内部流动作用的机理.数值计算结果表明:叶片端导叶的安装位置将影响轴流风扇气动效率,安装叶片端导叶不能提高风扇静压升,但是在压力面安装时能有效地减小风扇叶顶泄漏流与主流的掺混损失;在设计流量下,压力面安装叶片端导叶使泄漏涡的作用范围较小,涡核更靠近吸力面;吸力面安装叶片端导叶弱化了泄漏涡的强度但没有减小泄漏涡的作用范围。     

前缘弯掠斜流转子叶顶间隙流动特性数值分析

本文对前缘弯掠斜流转子叶顶间隙内的流动特性进行了数值分析。结果表明:叶顶间隙气流与主流发生卷吸而生成泄漏涡。泄漏涡作用的区域具有较低的压力分布。在叶片通道内,泄漏涡沿着与转子旋向相反的方向朝相邻叶片的压力面移动。大间隙时的泄漏涡比小间隙时强烈。低流量时泄漏涡的作用区域比高流量时大。在各种流量特性下,叶顶尾缘近吸力面区域都存在着二次间隙流。     

Chalcogenide based all-solid-state thin electroplated ion-selective membrane for Hg(II) flow-injection determinations

The response to Hg(II) of a thin all-solid-state Te-doped silver chalcogenide membrane, described by the general formula Ag₂ + δSe_{1 − x}Te_x, which has been electrochemically prepared following a previously proposed approach, has been investigated. The kinetics of formation of the membrane's secondary dynamic response to Hg(II) has been successfully combined with the precise timing and transient signal, typical for flow-injection (FI) measurements, in developing a sensitive and reliable mercury FI detector. Under optimized stream conditions it exhibits a linear Nernstian response, with a double slope of the calibration graph of 59 mV dec⁻¹, over the mercury(II) concentration range 10⁻⁶ − 10⁻³ M, the typical sample throughput amounting to about 70 samples per hour. The observed chemical amplification of the signal is due to the specificity of the processes dominating the initial step in formation of the steady-state signal of the membrane to mercury. The analytical performance of the Hg(II) FI detector, as regards sensitivity, reproducibility, selectivity and long-term stability has been thoroughly investigated. The exact procedure for membrane electrodeposition is given and the potential of the proposed approach as a cost-effective way for preparing chalcogenides of unique structure and properties has been outlined in the above context.     

Production of carbon soot with a high content of C60 and C70 fullerenes by electric arc

The effect of the parameters of the electric arc (helium pressure, current and voltage, clearance between electrodes) and of the peculiarities of the setup design (arrangement of electrodes, distance between the arc and the cooling surface, temperature of the soot condensation surface) on the yield of fullerenes has been studied. Conditions for producing soot with a C₆₀ and C₇₀ content up to 43% (toluene extract) have been found.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 5, pp. 805–809, May, 1994.The authors are grateful to N. G. Spitsyna and A. V. Dubovitskii for the determination of the content of C₆₀ and C₇₀ fullerenes in the extract.The work was financially supported by the Russian Foundation for Basic Research (Project 93-03-18705).     

Recognition of Monohydrogen Anions of Geometrical and Positional Isomers of Dicarboxylic Acids Based on Polymeric Liquid Membranes Incorporating Polyamine Host

Macrocyclic lipophilic polyamines were applied as the sensory elements of polymeric liquid membrane electrodes. These hosts gain the anion receptor functionality upon protons uptake from the aqueous solutions. The electrodes studied were able to distinguish potentiometricaly isomers of monocharged and doublecharged forms of ethylene and benzene dicarboxylic acids. The selectivity of interaction between protonated hosts and anionic guests relays not only on the electrostatic interactions, but on hydrogen bounds formations as well. The influence of lipophilicity of protonated hosts on the potential response generation was discussed.     

Reaction of SbPO4 with lithium in non-aqueous electrochemical cells: preliminary study and evaluation of its electrochemical performance in anodes for lithium ion batteries

SbPO₄, a phosphate with a layered structure, was tested as an electrode material for lithium cells spanning the 3.0-0.0 V range. Two main electrochemical processes were detected as extensive plateaus at ca. 1.6 and 0.7 V in galvanostatic measurements. The first process was found to be irreversible, thus excluding a potential intercalation-like mechanism for the reaction and being better interpreted as a decomposition reaction leading to the formation of elemental Sb. This precludes the use of this compound as a cathodic material for lithium cells. By contrast, the process at 0.7 V is reversible and can be ascribed to the formation of lithium-antimony alloys. The best electrochemical response was obtained by cycling the cell at a C/20 discharge rate over the voltage range 1.25-0.25 V. Under these conditions, the cell delivers an average capacity of 165 Ah/kg—a value greater than those reported for other phosphates—upon successive cycling.     

Computational Electrochemistry: A Model to Studying Ohmic Distortion of Voltammetry in Multiple Working Electrode,Microfluidic Devices,an Adaptive FEM Approach

Characteristics of mass transport and potential distribution applicable to microfluidic electrochemical flow cell devices has been modelled using the finite element method. A flexible, automatic grid generation algorithm has been combined with an a‐posteriori error indication technique presented by Nann and Heinze to allow irregular cell geometries to be modelled. The code has been applied to the problem of steady state generator – detector linear sweep voltammetry in a channel flow cell showing the effects of IR drop on the voltammetric response of each electrode.     

Transparent carbon nanotube coatings

Thin networks of carbon nanotubes (CNTs) are sprayed onto glass or plastic substrates in order to obtain conductive transparent coatings. Transparency and conductivity at room temperature of different CNT material are evaluated. CNT coatings maintain their properties under mechanical stress, even after folding the substrate. At a transparency of 90% for visible light we observe a surface resistivity of 1 kΩ/sq which is already a promising value for various applications.     

Activity evaluation of carbon paste electrodes loaded with pt nanoparticles prepared in different radiolytic conditions

Three Pt-based catalysts prepared in different radiolytic conditions and supported on graphite powder were packed into a carbon paste electrode configuration. They were compared to each other, to the commercial (Pt) deposited on activated carbon powder (Johnson Matthey) and to pure Vulcan XC-72 for their respective abilities toward the hydrogen evolution reaction (HER). The Tafel parameters were determined for all these electrodes. From the I–V curves and their quantitative treatment, the following order of activity emerged unambiguously and reads: (PtCO)₂ (fcc structure) > (PtCO)₁ (Chini cluster) > (Pt)_neat > (Pt)_JM (Johnson Matthey) ≫ (Vulcan XC-72). As expected, all the Pt-loaded electrodes were more efficient than Vulcan XC-72. The classification appears to be linked with the mean nanoparticle size, and for comparable sizes, with the surface morphology of the materials. The results and the stability of the electrodes suggest that the small particle sizes and the good dispersity on the carbon support were maintained during the HER.