Contact angle hysteresis of liquid drops as means to measure adhesive energy of zein on solid substrates

Adhesion of zein to solid substrates has been studied using surface energy profiles as indices and by adhesion mapping using atomic force microscopy (AFM). Different plasticizers like glycerol and sorbitol have been used to form mixed films with zein and properties of these films are studied using surface energy profiles. Comparison of the results from the different mixed samples with those from the pure zein films showed that force mapping could identify areas rich in protein. The adhesion maps produced were deconvoluted from sample topography and contrasted with the data obtained from contact angle measurements. A comparison of the two methods shows that the extent of contact angle hysteresis is indicative of both hydrophobicity of the surface as well as the force of adhesion. Mechanical properties and microstructure of zein films prepared by casting from solutions and using Langmuir-Blodgett film technique have been investigated. Pure zein seemed brittle and exhibited an essentially linear relationship between stress and strain. Films with plasticizer were tougher than these films. In general, mixed films showed better mechanical properties than pure films and had higher ultimate tensile strength and increased per cent elongation. Further, the mixed films of zein showed a higher force of adhesion compared to the pure films.     

Mössbauer and X-ray diffraction characterization of Fe60Al40 coatings prepared by thermal spraying

Microstructured (atomized) and nanostructured (milled) Fe₆₀Al₄₀ powders together with their corresponding coatings synthesized by High Velocity Oxy-fuel (HVOF) or Atmospheric Plasma Spray (APS) thermal spraying techniques have been characterized by Mössbauer Spectroscopy (MS) and X-ray Diffraction (XRD). The evolution of the microstructure and the atomic ordering degree in the powders and coatings are discussed at the light of the various processing conditions. The operational correlation between the parameters of the duplex morphology of coatings and the processing parameters is discussed.     

Thermal treatment on composite γ-zirconium phosphate-silica

The prepared amorphous γ-ZrP\SiO₂ composite had a complicated composition, since a part of γ-ZrP is converted to α-form during the exfoliation of it. The γ-ZrP\SiO₂ composite have specific surface area of 421 m²g^–1. The acidic P–OH groups of the lamellae species placed on the surface (it is ≈1.0 meq g^–1), do not destroy until the temperature of 1030 K. During the thermal treatment the total mass loss of 7.79% was found. This value corresponds to 0.42 mole of H₂O per molecule unit. The water loss process was found very slow, because of the placing of bilamellar species in the composite.     

Thermal decomposition of a generation 4.5 PAMAM dendrimer platinum drug conjugate

A nanoscale multivalent platinum drug based on a poly(amidoamine) [PAMAM] dendrimer (generation 4.5, carboxylate surface) has been synthesized and fully characterized using a variety of spectroscopic, chromatographic and thermal methods. Treatment of the dendrimer with an aqueous solution containing an excess diaquo(cis-1,2-diaminocyclohexane)platinum(II) produces a conjugate containing approximately forty (diaminocyclohexane)platinum(II) moieties at the surface of the dendrimer. This material undergoes smooth two-stage thermal decomposition to provide residual platinum oxide reflecting the platinum loading in the drug.     

纳米颗粒悬浮液池内泡状沸腾的实验研究

本文对纳米颗粒悬浮液在平壁面上池内沸腾进行了实验研究。实验用的纳米粒子为26 nm的铁粉和13 nm的三氧化二铝纳米粉末,基液为去离子水。分别配成体积浓度为0．1％, 1％和2％的悬浮液。实验结果表明,纳米悬浮颗粒对液体沸腾换热过程的影响会随着纳米颗粒性质,颗粒浓度及热流密度大小的不同而出现不同的效果;加入纳米颗粒后, 对基液沸腾换热的影响存在着两个相反的作用机制,它们分别为:纳米颗粒增强了液体内部的热量迁移能力(热物性的影响)和改变了加热面的表面结构特性(加热面特性的影响)。     

Studies on calcium‐containing poly(urethane ether)s

The calcium salt of mono(hydroxyethoxyethyl)phthalate [Ca(HEEP)₂] was synthesized by the reaction of diethylene glycol, phthalic anhydride, and calcium acetate. Calcium‐containing poly(urethane ether)s (PUEs) were synthesized by the reaction of hexamethylene diisocyanate (HMDI) or tolylene 2,4‐diisocyanate (TDI) with a mixture of Ca(HEEP)₂ and poly(ethylene glycol) (PEG₃₀₀ or PEG₄₀₀) with di‐n‐butyltin dilaurate as a catalyst. A series of calcium‐containing PUEs of different compositions were synthesized with Ca(HEEP)₂/PEG₃₀₀ (or PEG₄₀₀)/diisocyanate (HMDI or TDI) molar ratios of 2:2:4, 3:1:4, and 1:3:4 so that the coating properties of the PUEs could be studied. Blank PUEs without calcium‐containing ionic diols were also prepared by the reaction of PEG₃₀₀ or PEG₄₀₀ with HMDI or TDI. The PUEs were well characterized by Fourier transform infrared, ¹H and ¹³C NMR, solid‐state cross‐polarity/magic‐angle‐spinning ¹³C NMR, viscosity, solubility, and X‐ray diffraction studies. The thermal properties of the polymers were also studied with thermogravimetric analysis and differential scanning calorimetry. The PUEs were applied as top coats on acrylic‐coated leather, and their physicomechanical properties were also studied. The coating properties of PUEs, such as the tensile strength, elongation at break, tear strength, water vapor permeability, flexing endurance, cold crack resistance, abrasion resistance, color fastness, and adhesive strength, were better than the standard values. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2865–2878, 2003     

Effect of Hydrolysis Conditions on the Direct Formation of Nanoparticles of Ceria–Zirconia Solid Solutions from Acidic Aqueous Solutions

The effect of the cation concentration, hydrolysis temperature, and composition in the CeO₂–ZrO₂ system on the direct precipitation of ceria–zirconia solid solutions and the structure of the precipitates from acidic aqueous solutions of (NH₄)₂Ce(NO₃)₆ and ZrOCl₂ by hydrolysis under hydrothermal conditions were investigated. Nanometer-sized (8–10 nm) ceria–zirconia solid solution particles in a composition range of 0 to 60 mol% ZrO₂ were directly precipitated from the solutions with total metal cation concentration less than 0.2 mol/dm³ by simultaneous thermal hydrolysis at 150–240°C. The crystalline phase of the precipitates gradually changed from cubic and/or tetragonal to monoclinic with increasing the cation concentration of the solution from 0.2 to 0.8 mol/dm³ at the starting composition of 50 mol% ZrO₂ under hydrolysis condition of 150°C for 48 h, which was attributed to decrease in the supply of hydrolyzed Ce component caused by decrease in the hydrolysis ratio of (NH₄)₂Ce(NO₃)₆. Ceria–zirconia solid solutions containing large amount of ZrO₂ maintained high specific surface area and small-sized crystallite after heat-treatment at 900–1000°C for 1 h.     

Magnetic hysteresis of the magnetoresistance and the critical current density in polycrystalline YBa2Cu3O7−δ–Ag superconductors

A systematic study of the magnetic hysteresis in transport properties of polycrystalline YBa₂Cu₃O_7−δ–Ag compounds has been made based on two kinds of measurements at 77 K and under applied magnetic fields up to 30 mT: critical current density J_c(B_a) and magnetoresistance R(B_a). The R(B_a) curves show a minimum in their decreasing branch occurring at B=B_min which was found to be both the excitation current I_ex and the maximum applied magnetic field B_am dependent. In addition, for a certain value of B_am>5 mT, we have observed that B_min increases with increasing I_ex and reaches a saturation value. The J_c(B_a) curves show a maximum in decreasing applied magnetic fields occurring at B=B_max. We have also found that B_max increases with increasing B_am and reaches a saturation value. The minimum in the R(B_a) and the maximum in J_c(B_a) curves were found to be related to the trapped flux within the grains. All the experimental results are discussed within the context of the flux dynamics and transport mechanisms in these high-T_c materials.     

Dynamic mechanical thermal analysis transitions of partially and fully substituted cellulose fatty esters

The main transitions of cellulose fatty esters with different degrees of substitution (DSs) were investigated with dynamic mechanical thermal analysis. Two distinct main relaxations were observed in partially substituted cellulose esters (PSCEs). They were attributed to the glass‐transition temperature and to the chain local motion of the aliphatic substituents. The temperatures of both transitions decreased when DS or the number of carbon atoms (n) of the acyl substituent increased. Conversely, all the transitions of fully substituted cellulose esters occurred within a narrow temperature range, and they did not vary significantly with n. This phenomenon was explained by the formation of a crystalline phase of the fatty substituents. The presence of few residual OH groups in PSCEs was responsible for a large increase in the storage bending modulus, and it eliminated the effect of n on damping. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 281–288, 2003