An axial flow cyclone to remove nanoparticles at low pressure conditions

In this study, the axial flow cyclone used in Tsai et al. (2004) was further tested for the collection efficiency of both solid (NaCl) and liquid (OA, oleic acid) nanoparticles. The results showed that the smallest cutoff aerodynamic diameters achieved for OA and NaCl nanoparticles were 21.7 nm (cyclone inlet pressure: 4.3 Torr, flow rate: 0.351 slpm) and 21.2 nm (5.4 Torr, 0.454 slpm), respectively. The collection efficiencies for NaCl and OA particles were close to each other for the aerodynamic diameter ranging from 25 to 180 nm indicating there was almost no solid particle bounce in the cyclone. The 3-D numerical simulation was conducted to calculate the flow field in the cyclone and the flow was found to be nearly paraboloid. Numerical simulation of the particle collection efficiency based on the paraboloid flow assumption showed that the collection efficiency was in good agreement with the experimental data with less than 15% of error. A semi-empirical equation for predicting the cutoff aerodynamic diameter at different inlet pressures and flow rates was also obtained. The semi-empirical equation is able to predict the cutoff aerodynamic diameter accurately within 9% of error. From the empirical cutoff aerodynamic diameter, a semi-empirical square root of the cutoff Stokes number, , was calculated and found to be a constant value of 0.241. This value is useful to the design of the cyclone operating in vacuum to remove nanoparticles.     

滑坡冲击铲刮变量的计算方法研究

高速远程滑坡运动过程中,冲击铲刮效应不仅增加滑坡的体积与规模,而且会增大滑坡成灾范围,风险预测与判断出现明显误差,导致灾难性事件的发生。目前对于高速滑坡的铲刮深度、铲刮范围和铲刮体积等变量计算往往是采用基于经验的铲刮率算法,其是通过体积增量来反算铲刮变量的数学方法,而实际情况中高速滑坡的冲击铲刮是滑体冲击力和地表可铲刮材料之间的力学屈服破坏作用的结果。本文基于接触力学、弹塑性力学和岩土力学,提出了地表可铲刮层在附加冲击荷载作用下铲刮变量的理论计算方法,认为竖向冲击和切向剪切是滑体冲击铲刮过程的两种主要作用方式。结合实际岩土体材料参数,发现不考虑切向荷载时,铲刮层塑性区主要以竖向破裂区为主,考虑切向荷载时,铲刮层塑性区沿切向迁移,直至塑性边界贯通至地表,符合实际情况,实现了对铲刮变量的定量化计算。     

阻尼对空爆荷载等效静载动力系数的影响

为考查阻尼参数对空爆荷载等效静载动力系数的影响,理论推导了空爆荷载下结构等效单自由体系弹塑性位移解及延性比解,设计并计算了阻尼比0.000 1～0.1、延性比1～4的20种典型工况的动力系数,并与现行抗爆设计规范动力系数公式结果进行了对比。结果表明:阻尼比小于0.000 1时可基本代表无阻尼状态,阻尼比0.01的动力系数比无阻尼的最大降低幅度为2.08%,数值差异很小,因此阻尼比为0.01以内时,可忽略阻尼对动力系数的影响;阻尼比0.05的动力系数比无阻尼的降低幅度约9.92%,数值差异较大,认为阻尼比0.05以上时将具有明显的经济效益;现行设计规范动力系数更适用于柔性结构体系,运用于刚性结构抗爆设计时,计算误差较大,对阻尼比较小的结构设计更不利。     

Studies on the syntheses of polymetalloxanes and their properties as a precursor for amorphous oxide. IV. Properties of SiO2–TiO2 oxide fibers from polytitanosiloxane

From polytitanosiloxanes (PTS), SiO₂–TiO₂ oxide fibers with fairly good tensile strength were prepared, and their mechanical and thermal properties were investigated. The precursor fibers PTS-0.5 and PTS-1.0 were obtained by dry spinning of a highly viscous PTS solution which were formed as the reaction mixture of silicic acid (SA) with bis(2,4-pentanedionato)titanium diisopropoxide (PTP) in the molar ratios (SA/PTP) of 0.5 and 1.0. The precursor fibers PTS-0.5 were too brittle to measure their tensile strength, whereas PTS-1.0 and the heat-treated fibers were found to have tensile strength of 130 (precursor), 540 (500°C), and 450 (900°C) MPa, respectively. Heat-treatment of the fibers PTS-1.0 at above 1000°C forms anatase and rutile of titanium dioxide. The crystallization is resulted from the unreacted PTP which is not incorporated into the polymer network.     

Synthesis,characterization, and mechanical properties of PMMA/poly(aromatic/aliphatic siloxane) semi-interpenetrating polymer networks

Semi-interpenetrating polymer networks (IPNs) composed of poly(methyl methacrylate) (PMMA) and aromatic/aliphatic siloxanes have been made via sequential and simultaneous polymerizations. As the percentage of aliphatic siloxane increases, flexibility and, in general, toughness of the IPNs increases and clarity is reduced. This loss in clarity is due to the mismatch of refractive indices (1.49 form PMMA vs. 1.43 for aliphatic siloxane). PMMA is quite transparent. On the other hand, in making aromatic siloxane/PMMA IPNs clarity is retained as aromatic siloxane is increased due to better matching refractive index (1.49 for PMMA and −1.49 for poly(diphenyl siloxane)). Gel permeation chromatography (GPC) indicates slightly crosslinked IPNs with the THF soluble portions having number-average molecular weight, M¯_n, of 10⁵–10⁶. NMRs of IPNs essentially show peaks for the components, PMMA and the siloxane, which make up the respective IPNs. ²⁹Si-NMRs indicate cross-linking and grafting. Mechanical properties show increased toughness of IPNs versus PMMA as percentage of siloxane and crosslinker increases, but with a corresponding loss in tensile strength. © 1996 John Wiley & Sons, Inc.     

Flume testing of passively adaptive composite tidal turbine blades under combined wave and current loading

The tidal energy industry is progressing rapidly, but there are still barriers to overcome to realise the commercial potential of this sector. Large magnitude and highly variable loads caused by waves acting on the turbine are of particular concern. Composite blades with in-built bend-twist elastic response may reduce these peak loads, by passively feathering with increasing thrust. This could decrease capital costs by lowering the design loads, and improve robustness through the mitigation of pitch mechanisms. In this study, the previous research is extended to examine the performance of bend-twist blades in combined wave–current flow, which will frequently be encountered in the field. A scaled 3 bladed turbine was tested in the flume at IFREMER with bend-twist composite blades and equivalent rigid blades, sequentially under current and co-directional wave–current cases. In agreement with previous research, when the turbine was operating in current alone at higher tip speed ratios the bend-twist blades reduced the mean thrust and power compared to the rigid blades. Under the specific wave–current condition tested the average loads were similar on both blade sets. Nevertheless, the bend-twist blades substantially reduced the magnitudes of the average thrust and torque fluctuations per wave cycle, by up to 10% and 14% respectively.     

纵横载荷作用下功能梯度梁的弯曲和过屈曲

基于一阶非线性梁理论和物理中面概念,导出了纵横向载荷作用下功能梯度材料(FGM)梁非线性弯曲和过屈曲问题的控制方程,并获得了该问题的精确解;据此解研究了梯度材料性质、外载荷、横向剪切变形以及边界条件等因素对功能梯度材料梁非线性力学行为的影响,分析中假设功能梯度材料性质只沿梁厚度方向,并按成分含量的幂指数函数形式变化。结果表明:纵横载荷共同作用下,功能梯度梁的弯曲构形将有无限多个;随着梯度指数的增大,梁的变形减小,临界载荷升高;随着长高比的增大,横向剪切变形的影响减小。     

水硬性石灰合成及拉破坏特性试验研究

水硬性石灰在欧洲石质文物修复和加固中获得了很大成功。我国的石质文物主要是砂岩,水硬性石灰的修复效果不好。为满足我国石质文物修复和加固的需求,本文以石灰石和黏土为原料,在950℃煅烧不同时间,制备出水硬性石,对试样的成分、微观形貌、收缩率、抗拉强度和拉破坏过程等进行了研究。结果表明:(1)试样中含有水硬性成分2CaO·SiO2(C2S);煅烧8h时,成分与欧洲水硬性石灰NHL5接近;1.5CaO·SiO2·xH2O(C-S-H)和CaCO3的含量随龄期的增加逐渐增加。(2)龄期1~3d,收缩率较小;龄期4~6d,收缩率以线性规律增加;7d以后,收缩率趋于稳定。(3)局部变形区随拉应力的增加而变大,邻近局部变形区逐渐合并,形成面积更大的应变局部化带;载荷超过峰值后,产生微裂隙;随载荷进一步增加,微裂隙扩展,贯穿整个试件,发展成宏观裂隙,使试件破坏。(4)抗拉强度随龄期的增加而增加,水硬性石灰中C-S-H、CaCO3等相互交织,构成空间致密体,使试件力学强度提高。合成的水硬性石灰物理力学性能与欧洲水硬性石灰NHL5相近,并且成分均匀、可控,在石质文物修复和加固工程中具有良好应用前景。     

丙烯酸盐喷膜防水材料在酸碱浸润和冻融循环条件下的耐久性试验分析

丙烯酸盐喷膜防水材料在酸碱溶液浸润和冻融条件下的耐久性能是该类材料在工程应用中较难回避的实际问题,论文采用酸性介质(0.2%的H2SO4溶液)和碱性介质(0.1%NaOH+饱和Ca(OH)2溶液)对该材料进行饱和浸泡并进行冻融循环后,研究了该材料的吸水性、断裂拉伸强度和拉断伸长率的变化规律。试验结果表明:喷膜防水材料在侵蚀-冻融循环作用下,其拉断伸长率和断裂拉伸强度显著降低,且酸性介质对材料拉伸性能的影响较大;材料耐低温冰冻能力较强,耐高温能力较差。反映出丙烯酸盐喷膜防水材料在低温冰冻和碱性介质中耐久性较好,不建议在高温和酸性介质条件下使用。     

转动惯量法在多轴疲劳本构关系预测中的应用

一些金属材料在承担多轴非比例加载过程时,会产生额外非比例附加强化或软化现象,这一现象往往会导致在评估疲劳寿命时因为材料本构关系的不确定而引起预测结果出现较大误差．因此基于单轴疲劳理论得出的寿命预测模型并不能准确地预测多轴非比例疲劳加载下的材料寿命．针对此问题,本文阐述了非比例附加强化效应产生的原因及结果,结合转动惯量法的理论和塑性增量法,建立了预测多轴低周疲劳加载下循环应力-应变曲线的数值计算模型．利用316L 不锈钢试样在5 种加载路径下的实验数据对预测结果进行了验证,结果表明该模型具有良好的预测有效性及精度．