Selective Oxidation of Alcohols with a New Reagent: Iron(III) Nitrate Supported on Aluminum Silicate

A selective and effective oxidation of alcohols, except aliphatic alcohols, such as 1‐hexanol or 1‐octyl alcohol, to the corresponding aldehydes and ketones using a new reagent, iron(III) nitrate supported on aluminum silicate, under heterogeneous conditions with reflux with 85–98% yield is described.     

Reagentless Bioluminescent Sensor for NADH

Abstract

A reagentless fiber optic biosensor specific for NADH, associated with flow injection analysis and based on bacterial bioluminescence is described. Only a buffer solution as flowing stream is required for the probe which works without supply of its coreactants (FMN and N-decyl-aldehyde). These are coentrapped in a poly(vinyl)alcohol (PVA) matrix which allows their internal release in the vicinity of the immobilized enzymes. Two PVA matrices differing by the reticulation process have been tested : first, by polymerization with glutaraldehyde and secondly, by a cyclic freezing-thawing process. The self-containment working time was estimated at 1 and 1.5 h of continuous measurements, respectively. NADH was determined using flow injection analysis. The sensor gave excellent reproducibility (RSD ≤ 3%) in the linear dynamic range 5 — 500 pmol with an average cycle-time of 2.5 min.     

“蜡烛火焰划分”实验的局限成因分析及改进研究

人教版初中化学首个探究性实验"蜡烛及其燃烧"明确指出火焰的划分方法，但在实际教学中肉眼观察法和火柴梗燃烧法对蜡烛火焰的划分存在一定的局限性。采用文献研究法和实验验证法分析其局限性的成因——燃料的析炭能力强弱、材料结构的不同等，并提出相应的改进建议。     

Chain transfer agents in cationic photopolymerization of a bis‐cycloaliphatic epoxide monomer: Kinetic and physical property effects

The effects of chain transfer agents (CTA) on cationic ring‐opening polymerization of 3,4‐epoxycyclohexylmethyl‐3′,4′‐epoxycyclohexane carboxylate (EEC) were explored. EEC was polymerized in the presence of various CTAs, and epoxide conversions monitored via Raman spectroscopy. Polymer films were prepared and analyzed by dynamic mechanical analysis. Many of the organic alcohols studied greatly enhanced epoxide polymerization rates and conversion levels. The gel fraction of polymer specimens decreased rapidly with increasing amounts of octanol (gel fraction >90% up to 0.3 equiv OH) but remained high with increasing amounts of 1,2‐propanediol (gel fraction >90% up to 0.6 equiv OH). Increasing the size of primary alcohols had little effect on the polymerization rates and conversions. The polymerization rate decreased with increasing alcohol substitution (1°>2°>3°). Acidic alcohols had very low impact on conversion and polymerization rates relative to the neat epoxy resin. The glass transition temperature was inversely related to the size and amount of CTA. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis and Characterization of the First Pyrrolidine‐Based Chiral Ionic Liquids

The first example of pyrrolidine‐based room‐temperature chiral ionic liquids using 2‐aminobutanol as chiral auxiliary is described.     

Fabrication and Optimization of Poly(vinyl alcohol)/Zirconium Acetate Electrospun Nanofibers Using Taguchi Experimental Design

This paper presents an investigation regarding poly(vinyl alcohol)/zirconium acetate (organic–inorganic) (PVA/Zrace) nanofibers prepared by electrospinning which could be used as a precursor for fabricating ceramic metal oxide nanofibers. The effect of some processing variables, including polymer solution concentration, tip to collector distance and applied voltage of electrospinning, and the amount of Zrace and their interactions, on the diameter of the nanofibers were studied. Taguchi experimental design and a statistical analysis (ANOVA) were employed and the relationship between experimental conditions and yield levels determined. It was concluded that to obtain a narrow diameter distribution as well as maximum fiber fineness, a polymer concentration of 10 wt%, tip to collector distance of 18 cm and applied voltage of 20 kV variables were the optimum. Furthermore, it was also concluded that the ratio of Zrace (6 g) to PVA solution (10% wt) played an important role for achieving the minimum fiber diameter. Under these optimum conditions, the diameters of the electrospun composite fibers ranged from 86 nm to 381 nm with a diameter average of 193 nm. The experiments were done with Qualitek-4 software with “smaller is better” as the quality characteristics. The optimized conditions showed an improvement in the fibers diameter distribution and the average fibers diameter showed good resemblance with the result predicted using the Taguchi method and the Qualitek-4 software. The ANOVA results showed that all factors had significant effects on the fibers diameter and distribution, but the effect of PVA concentration and zirconium acetate were more significant than the other factors.     

Feasibility of Polyvinyl Alcohol as a Transdermal Drug Delivery System for Terbutaline Sulphate

A series of terbutaline sulphate drug incorporated polyvinyl alcohol (PVA) matrix films were produced by the solvent evaporation method. The effect of xanthan gum and plasticizers (propylene glycol and dibutyl phthalate) on the rate and amount of drug diffusion from PVA membrane across the hydrated cellophane membrane has been evaluated, using an open glass diffusion‐tube. The obtained films were clear, smooth and flexible having sufficient mechanical strength. The mechanical performance of the dry PVA films with xanthan gum and plasticizers were also ascertained. Polyvinyl alcohol‐xanthan gum blends showed a high rate of drug release compared to that of polyvinyl alcohol film alone. Among the two plasticizers employed, propylene glycol showed better permeability. Among different formulations studied, the formulation PVA/xanthan gum/propylene glycol (F7) was found to be an optimized composition for efficient transdermal delivery of the model drug, terbutaline sulphate. The mechanism of drug diffusion has been evaluated using the Peppas model. Stability studies carried out on polymer‐drug formulations revealed that the drug is stable at 40°C and 75% RH for a period of 6 weeks.     

Evaluation of the (Allyl alcohol 1,2‐butoxylate‐block‐etoxylate)‐b‐PMMA Copolymers Composition by the Dielectric Measurements

Redox initiated free‐radical polymerization of methyl methacrylate (MMA) with allyl alcohol 1,2‐butoxylate‐block‐etoxylate (AABE) was carried out to yield AABE‐b‐PMMA copolymers at elevated temperatures. The composition of the copolymers depending on the polymerization temperature was qualitatively estimated by the dielectric measurements. It has been seen that AABE segment quantity decreased and PMMA segment quantity increased with increasing the polymerization temperature. The dielectric constant and the dissipation factor of the copolymers were investigated as a function of frequency and temperature. The dielectric constant and the dissipation factor were found to be strongly affected by the polymerization temperature. The highest dielectric constant in all studied temperatures and frequencies was obtained in the case of the copolymer which was prepared at 313 K. The dipolar C‐O and OH groups of the AABE segment have the primary effect on the dielectric constant. The copolymer which was prepared at 323 K, showed the highest dissipation factor near the relaxation temperature of PMMA.