汽轮机转子的温度场及热应力场计算

利用积分变换法导出了蒸汽温升率连续变化时汽轮机转子的温度场和热应力场计算公式。本公式可直接应用于转子的应力监测与控制。和差分法相比，解析法的数据处理速度快，能满足快速监测、及时跟踪与控制的要求。关键词：汽轮机转子；温度场；热应力场     

水和水蒸汽热力学物性参数及导数的计算与应用

本文针对现代换热设备设计、两相流动与传热研究的需要,介绍了可供科研使用的水和水蒸汽物性计算方法,完善了计算程序。根据超临界锅炉设计中的超临界水的物性计算,两相流研究和换热设备动态特性研究中对物性导数计算的需要,提供了两个算例,并进行了定性分析。     

水蒸气对褐煤原位气化半焦反应性能及微观结构的影响

为了揭示水蒸气对半焦反应性和微观结构的影响,在自制两段新型反应器上依次进行了褐煤干燥、热解及"热"焦的水蒸气原位气化研究。利用TGA、BET和Raman光谱仪,对原位气化半焦进行反应性和微观结构解析。结果表明,在反应温度为600 ℃时,水蒸气对半焦转化率、反应性及微观结构影响很小。温度达到700~900 ℃,在半焦与水蒸气接触的前2 min,虽然半焦转化率变化不大,但其反应性、小环(3~5个芳环)与大环(≥6个环)体系之比及含氧官能团却急剧降低;大于2 min,半焦转化率逐渐增大,反应性、小环与大环之比及含氧官能团缓慢降低;而半焦孔结构在2 min 前后却具有基本一致的变化趋势。半焦与水蒸气接触的前2 min,小环与大环之比和含氧官能团急剧降低是导致反应性显著降低的重要因素,大于2 min,芳环体系的变化是导致反应性进一步降低的原因。     

碱金属钾对Ni基催化剂纤维素水蒸气气化活性的影响

采用两段式催化气化方式研究了生物质热解气化过程中碱金属的挥发对Ni基催化剂活性的影响。实验结果表明,负载K盐的纤维素水蒸气催化气化过程中,K挥发后会在催化剂表面沉积,而少量K的存在和表面沉积不但能够提高镍基催化剂的抗积炭能力,而且有助于提高其催化活性,产生更多的氢气。然而纤维素中K的浓度过大,将会抑制Ni基催化剂的效果;K在催化剂上的沉积随催化剂循环次数的增加而增加,K的含量愈高,对催化剂的抑制效果愈明显,从而缩短了催化剂的使用寿命。     

氧化钙对胜利褐煤焦水蒸气气化反应性能及微结构的影响

研究了CaO对胜利褐煤焦水蒸气气化反应性能及微结构的影响。脱除矿物质的胜利褐煤混合不同含量的CaO后在1 100 ℃下进行热解得到相应的煤焦,采用BET、XRD和Raman技术对其进行表征,同时在微型固定床反应器上对所制得煤焦进行水蒸气气化实验。比较添加CaO不同含量煤焦的反应性表明,添加2%(质量分数)的CaO对煤焦水蒸气气化的催化作用很小,而CaO添加量增大到5%时,煤焦的气化反应性能明显提高。煤焦比表面积随CaO添加量的提高而增大。XRD结果表明,在热解过程中,CaO能有效地抑制煤焦向石墨化方向发展趋势。煤焦002和100峰的峰强度随CaO添加量的增加而降低,且煤焦芳香度从66.8%降至39.9%。Raman光谱结果表明,随着CaO添加量的增加,I_D/I_G由1.363增加至1.541,I_G/I_all由0.423减少到0.394。意味着由于Ca的催化作用,煤中大芳香环结构的裂解速率明显增加,且随CaO添加量的增多,煤焦的无序化程度和晶格缺陷均增大。     

Heat transfer in bubble layers at elevated pressures

Heat transfer with steam condensation under moderate pressure on the surface of a horizontal tube immersed in a bubbling layer was experimentally investigated. A copper test section 16 mm in outer diameter and 400 mm in length was placed in a bubbling column 455 mm in diameter. Experiments were made under pressures of 0.14–0.8 MPa, with void fraction 0.04–0.23, vapor superficial velocities 0.05–0.42 m/s, liquid-wall temperature differences 47–105 K, and heat flux densities 0.12–0.8 MW/m². The heat transfer process in the bubbling layer is shown to be of a high intensity: with moderate values of steam content, heat transfer coefficients reach 12–14 kW/(m² · K). Data obtained showed that the known correlations do not consider the influence of pressure on heat transfer. For the first time, data on radial steam content distribution under pressures higher than atmospheric were obtained by an electroprobe method. A table of experimental data is presented.     

Heat transfer in bubble layers at high pressures

An original experimental investigation of heat transfer with steam condensation on a surface of a horizontal cooled tube immersed in a bubbling layer was carried out. A copper test section 16 mm in diameter and 285 mm in length was placed in a bubbling column 295 mm in diameter. Experiments were made under a pressure of 0.72-3.8 MPa with volume steam content 0-0.18, steam superficial velocities 0-0.18 m/s, and liquid-wall temperature difference 38–106 K. The heat transfer process in a bubbling layer under high pressures is shown to be of considerably intensity; with moderate values of steam content heat transfer coefficients reach 10–12 kW/(m²·K). The use of the known correlations assumed for the case of air bubbling under atmospheric pressure results in systematically underestimating heat transfer by 30–80%. Data were obtained on heat transfer with film condensation of steam and natural convection of subcooled water at high temperature differences outside the range investigated earlier. Experimental data table is appended.     

Hydrogen production from the aqueous phase derived from fast pyrolysis of biomass

Hydrogen production from the aqueous phase derived from fast pyrolysis of biomass was carried out by catalytic steam reforming in a fluidized bed reactor. The effects of reaction conditions such as reaction temperature, steam-to-carbon ratio (S/C) and weight hourly space velocity of the aqueous phase (WHSV) on the results of hydrogen yield, potential hydrogen yield and carbon selectivity of product gases were investigated. The effect of reaction temperature on the carbon deposition on catalyst was also studied. The hydrogen yield of 64.6%, potential hydrogen yield of 77.6% and the carbon selectivity for product gases of 84.3% can be obtained at the optimized conditions of reaction temperature 800 °C, S/C 10 and WHSV 1.0 h⁻¹.     

两段式固定床富氧－水蒸气气化实验研究

以玉米芯颗粒为原料在两段式固定床气化装置上进行了气化实验,考察了当量比ER、富氧浓度OC和水蒸气配比S/B对气化温度、气化气组分、低位热值、气体产率、气化效率和碳转化率等参数的影响,并比较了两段式固定床与传统下吸式固定床的气化特性。实验结果表明,当量比为0.27时H₂的体积分数、CO的体积分数和气化效率达到最大值;增加富氧浓度能优化气化效果,但富氧浓度大于90%后,燃气质量和气化效率均提高不大;增加S/B能提高H₂的体积分数,但同时会降低CO的体积分数、气体热值、气化效率;当S/B为0.6时,氢气的体积分数达最高值33.3%,H₂/CO比为1.32;相比于传统固定床,两段式固定床气化可明显提高气化温度、氢气的体积分数、碳转化率和气化效率,降低焦油含量。     

The porosity, acidity, and reactivity of dealuminated zeolite ZSM-5 at the single particle level: the influence of the zeolite architecture

A combination of atomic force microscopy (AFM), high‐resolution scanning electron microscopy (HR‐SEM), focused‐ion‐beam scanning electron microscopy (FIB‐SEM), X‐ray photoelectron spectroscopy (XPS), confocal fluorescence microscopy (CFM), and UV/Vis and synchrotron‐based IR microspectroscopy was used to investigate the dealumination processes of zeolite ZSM‐5 at the individual crystal level. It was shown that steaming has a significant impact on the porosity, acidity, and reactivity of the zeolite materials. The catalytic performance, tested by the styrene oligomerization and methanol‐to‐olefin reactions, led to the conclusion that mild steaming conditions resulted in greatly enhanced acidity and reactivity of dealuminated zeolite ZSM‐5. Interestingly, only residual surface mesoporosity was generated in the mildly steamed ZSM‐5 zeolite, leading to rapid crystal coloration and coking upon catalytic testing and indicating an enhanced deactivation of the zeolites. In contrast, harsh steaming conditions generated 5–50 nm mesopores, extensively improving the accessibility of the zeolites. However, severe dealumination decreased the strength of the Brønsted acid sites, causing a depletion of the overall acidity, which resulted in a major drop in catalytic activity.