Solubility Measurements of Surfactants and Dissolution of Cytochrome c in 1,1,1,2‐Tetrafluoroethane Modified with Organic Solvents

The solubilities of four surfactants, sodium bis‐2‐ethylhexyl sulfosuccinate (AOT), cetyltrimethylammonium chloride, didodecyldimethylammonium bromide, and n‐dodecyltrimethylammonium chloride in liquid refrigerant 1,1,1,2‐tetrafluoroethane (R134a) modified with methanol, ethanol, and 2‐propanol were measured. The measurements were performed under 25 and 50 bar at 25 °C. The solubility of AOT was as high as 92 mM in R134a with addition of 2% ethanol. Cytochrome c molecules were then verified to be soluble in the AOT‐containing and ethanol‐modified R134a solution. Accordingly, liquid R134a is suggested as a potential extraction solvent for hydrophilic compounds.     

Zeta-potentials of self-assembled surface micelles of ionic surfactants adsorbed at hydrophobic graphite surfaces

The zeta-potentials of the self-assembled surface ionic surfactants (sodium dodecyl sulfate—SDS and hexadecyltrimethyl ammonium bromide—CTAB) on graphite surfaces were determined both from streaming potential and electrophoretic mobility measurements. The adsorption of the surfactants at graphite–liquid interfaces has been studied using atomic force microscopy (AFM) soft-contact imaging which shows the formation of linear, parallel hemicylinders with headgroups oriented towards the solution. The magnitude of the zeta-potential increased with an increase in surfactant concentration, reaching a constant value at a concentration corresponding to the point of surface micelle formation as confirmed from AFM imaging. The streaming potential and electrophoretic mobility measurements showed that the zeta-potentials of SDS and CTAB surface micelles adsorbed at the graphite surface were about −75 and +70 mV, respectively, well in agreement with the values reported for bulk phase micelles in the literature.     

Reversible Melting of Semi-Crystalline Polymers 2. Annealing Near to the Melting Point

Annealing experiments have been carried out at a few degrees below the melting point of different polyethylenes (LDPE, LLDPE, HDPE), of polypropylene (PP) and of Nylon-6. The heat capacities decrease during the annealing, within a 2-4 min time scale, to a lower value which corresponds to the extrapolated heat capacity values obtained for the cooling cycle when the polymer is cooled from the melt. Heat capacities in the heating cycle following the cooling cycle of PP, Nylon-6 and HDPE have the same value as during the cooling section. This is not the case for LDPE and LLDPE. Exothermic total heat flow in the cooling section following the annealing indicates that the crystallisation takes place during the cooling rather than during the annealing period. The total melting enthalpy measured before and after the annealing cycle is the same. The reversing heat flow shows an excellent fit to the change of the crystallinity measured by small angle scattering of synchrotron radiation during a heating cycle at temperatures below the melting peak. A coupled thermodynamic interaction of the crystalline and the amorphous phases is concluded from this study. This kind of interaction is possible at the lateral end of polymeric chains incorporated into the crystalline phase. This is an indication of the portion of tie molecules in the system, i.e. the portion of fringed micelle type of crystalline morphology with respect to that of folded chain lamellae. This revised version was published online in July 2006 with corrections to the Cover Date.     

The mean spherical model in a random external field and the replica method

We provide a quick elementary solution of the mean spherical model in a random external field. This also allows an immediate proof of the self-averaging property of the free energy. We calculate the free energy by means of the replica method, i.e., for any (not necessarily integer) replica numbern, and show that when a phase transition occurs the limits andn 0 are not interchangeable.     

Impact of micelles on the biocidal efficiency in a diesel–water interface

Biodegradation occurs in the diesel/water interface in petroleum product pipelines. The microbial contamination can result in inhibitor/fuel degradation, leading to unacceptable levels of turbidity, filter plugging, storage tank corrosion and stored product souring. Therefore, selection of the biocide/inhibitor plays an important role in the transportation of petroleum products through pipelines. Three biocides (cationic and nonionic) were employed to study the biodegradation in a diesel‐water interface. The biocidal efficiency against degradation of diesel was examined by employing Fourier‐transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (NMR) spectroscopy and gas chromatography mass spectrometry (GC‐MS) techniques. Bronopol (2‐bromo‐2‐nitro‐propane‐1, 3‐diol) was found to have higher bactericidal efficiency than N‐cetyl‐N,N, N‐trimethyl ammonium bromide (CTAB) and cetyl pyridinum bromide (CPB). But the cationic biocides (CTAB and CPB) showed good biocidal efficiency at the interface. The data are explained in terms of a model that postulates the formation of a ‘micelle’ at the diesel‐water interface. Copyright © 2007 John Wiley & Sons, Ltd.     

Determination of Aggregation Parameters of Hexadecyltrimethylammonium Bromide from Probe Absorption

The mean aggregation number (n) and the critical micelle concentrations (CMC) of reverse micelles formed by hexadecyltrimethylammonium bromide have been determined by means of an optical absorption probe (acridine orange). The procedure to obtain these quantities from absorption spectrophotometric measurements is described. The CMC and mean aggregation number are in satisfactory agreement with published results obtained from more sophisticated methods.     

The solubilization of alcohols in micellar solutions

The specific conductivities of dodecyldimethylbenzylammonium bromide (C12BBr) have been determined in aqueous butanol and aqueous benzyl alcohol solutions in the temperature range of 5-40°C. From these data the temperature dependent critical micelle concentration (cmc) was determined. The molar fraction of alcohol in the micelle was estimated using the theory suggested by Motomura et al. for surfactant binary mixtures. The thermal properties such as standard Gibbs free energy, enthalpy and entropy of solubilization of alcohols in the micelles were estimated for the phase separation model. The change in heat capacity upon solubilization of alcohol in the micelle has been estimated form the above properties. This revised version was published online in July 2006 with corrections to the Cover Date.     

Self-aggregation and phase behavior of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) block copolymers in aqueous solution

The phase behavior and aggregation properties of block copolymers of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (Pluronics, poloxamers) in aqueous solution have recently attracted much attention. Both experimental and theoretical studies are reviewed, not comprehensively, but with the focus on studies, partly cooperative, partly independent, performed by groups in Uppsala (light scattering and fluorescence), Roskilde (rheology and calorimetry), Risø (SANS), Graz (x-ray and speed of sound), and Lund (theoretical model calculations).The phase behavior of these copolymers is similar in many respects to that of conventional nonionic surfactants, with the appearance of hexagonal, cubic, and lamellar liquid crystalline phases at high concentrations. In the isotropic solution phase the critical concentration for micelle formation is strongly temperature dependent, and at a given concentration the monomer to micelle transition occurs gradually over a broad temperature range, partly due to the broad size polydispersity of both the PO- and EO-blocks. For some Pluronic copolymers a transition from globular to long rod-like micelles occurs above a transition temperature, resulting in a strong and sudden increase of viscosity and viscoelasticity of the solution.Size and aggregation numbers have been determined for the globular micelles in some cases, and also the rod-like micelles have been characterized. NMR and fluorescence measurements have provided further information on the properties of the micellar core and mantle. In combination, results from different measurements on the same Pluronics material indicate that the aggregation number of the micelles increases with the temperature, whereas the hydrodynmic radius varies much less. The PEO-mantle of the micelles seems to contract with increasing temperature. The core appears to contain appreciable amounts of PEO in addition to PPO (and also some water). The segregation between core and mantle is not as distinct as in normal micelles, a conclusion which is in line with the predictions from the model calculations.     

Effect of pressure on the adsorption and micelle formation of aqueous dodecyltrimethylammonium chloride solution-hexane system

The interfacial tension of aqueous dodecyltrimethylammonium chloride (DTAC) solution/hexane interface has been measured as a function of pressure at concentrations around the critical micelle concentration (CMC). The derivative of the interfacial tension with respect to pressure has been observed to change abruptly at the CMC as in the case of aqueous dodecylammonium chloride (DAC) solution-hexane system studied already. The volume changes associated with the adsorption of DTAC from its monomeric and micellar states have been calculated. The results have indicated that the micelle formation of surfactant is treated like the appearance of a new macroscopic phase in the system. It has also been concluded that the micelle solubilizing hexane bears resemblance to the adsorbed film in terms of the volume. The difference in the pressure dependence of the volume of micelle formation ^MW between DTAC and DAC has been attributed to a larger polar group of DTAC. The fact that the value of ^MW is larger than that estimated from the conductivity data has been explained by the solubilization of hexane into the micelle.     

The aggregation of sodium dehydrocholate in water

 We used a battery of different methods to study the association in aqueous sodium dehydrocholate (NaDHC) solutions. This salt associates by a stepwise mechanism. Below (9.6 ± 4.2) × 10⁻⁴ mol dm⁻³ there is a molecular solution with some strongly insoluble dehydrocholic acid produced by hydrolysis. Between (9.6 ± 4.2) × 10⁻⁴ and (5.2 ± 2.2) × 10⁻³ mol dm⁻³, an aggregate similar to acid soap (NaDHC.HDHC) appears and its amount and the aggregate's size increase with concentration. At =(2.20 ± 0.85) × 10⁻² mol dm⁻³ the aggregates formed have properties usually associated with true micelles, such as solubilisation of water-insoluble dyes. These aggregates increase in size with concentration and change their shape at 8 × 10⁻² mol dm⁻³, giving nonsymmetrical aggregates. The changes in the solution physicochemical properties at these concentrations may be misinterpreted and this explains the different values of the critical micelle concentration reported in the literature for substances with similar structure, such as bile salts. Received: 14 May 2001 Accepted: 10 August 2001