定量的复合金属锂作为三维泡沫锂电极用于锂电池的研究

金属锂作为电池的负极材料具有极高的比容量和极低的氧化还原电位,能够显著提升电池的能量密度。然而,金属锂负极在实际应用中所面临的主要问题是锂枝晶、界面副反应和电极体积变化大的难题。在本文中,我们提出了一种通过将定量的金属锂与三维骨架进行复合形成三维泡沫锂负极的策略,并利用三维泡沫锂来抑制锂枝晶的生长和缓解电极的体积变化。因此,三维泡沫锂电极有利于金属锂负极的高效利用,并能借助其与平面锂箔相比更高的比表面积和更多的反应位点来提升电池的倍率性能。因此,通过采用三维泡沫锂,对称电池的循环寿命和倍率性能都得到了有效的提升。EIS数据结果表明,三维泡沫锂能够减小对称电池的电荷转移阻抗。而且,将三维泡沫锂作为负极组装的LTO全电池,与锂箔作为负极相比,循环1000周平均放电比容量从65 mAh·g^-1提升至121 mAh·g^-1。     

基于离子液体的超级电容在3 V及65 oC老化条件下的铝碳界面效应

相比于传统乙腈电解液体系的超级电容器,离子液体基超级电容器具有工作窗口电压高,能量密度大,不可燃等优点,适用于碳中和时代清洁但不稳定电力领域的大规模储能。然而,目前的工作主要集中在对纽扣型离子液体-超级电容器的研究上,有关软包式离子液体-超级电容器的长循环寿命评测的报道较少。构建可靠的超级电容器用于长时间测试或在高温下开展加速老化测试,应考虑集流体/电极界面的良好接触,以最小化电荷转移电阻。本文以包覆不同碳层的泡沫铝为集流体,研究了超级电容器新系统中的碳-铝界面效应。通过环氧树脂薄膜碳化得到的均匀无定形碳层,相比通过PVDF粘附石墨烯碳层,赋予了铝相和碳相更强的相互作用。此外,为了充分挖掘大离子尺寸的离子液体电解液的潜力,本文采用介孔碳电极实现离子在介孔间的快速扩散。因此,本工作首次制备了由介孔碳电极、离子液体电解液和覆碳三维泡沫铝集流体组成的新结构软包式超级电容器。以自制的容量为37 F的不同软包式超级电容器件,通过3 V、65 ^oC、500 h加速老化试验,研究了其时间依赖性的电化学性能,包括CV测试、恒流充放电测试、电容值、接触电阻、电化学阻抗谱等。相比石墨烯包覆的泡沫铝基器件,无定形碳层包覆的泡沫铝基器件表现出更高的电容保持率。此外,我们还对ESR进行了等效电路拟合,并深入分析了接触电阻、电荷转移电阻、韦伯电阻,研究了C-Al界面对高能量密度超级电容器的高性能和稳定性的影响。500小时老化测试前后的极片表征证实了上述结果。高温、高压条件使粘附石墨烯碳层的泡沫铝界面结构不可靠。而泡沫铝表面原位包覆的碳层在老化过程中表现出较强的相互作用和稳定的结构。这些坚实的数据为面向高能量密度、高功率密度和长循环寿命,进一步优化高窗口电压超级电容器提供了充足的信息。     

Synthesis of activated carbon foams with high specific surface area using polyurethane elastomer templates for effective removal of methylene blue

Carbon foams have gained significant attention due to their tuneable properties that enable a wide range of applications including catalysis, energy storage and wastewater treatment. Novel synthesis pathways enable novel applications via yielding complex, hierarchical material structure. In this work, activated carbon foams (ACFs) were produced from waste polyurethane elastomer templates using different synthesis pathways, including a novel one-step method. Uniquely, the produced foams exhibited complex structure and contained carbon microspheres. The ACFs were synthesized by impregnating the elastomers in an acidified sucrose solution followed by direct activation using CO₂ at 1000 ℃. Different pyrolysis and activation conditions were investigated. The ACFs were characterized by a high specific surface area (S_BET) of 2172 m²/g and an enhanced pore volume of 1.08 cm³/g. Computer tomography and morphological studies revealed an inhomogeneous porous structure and the presence of numerous carbon spheres of varying sizes embedded in the porous network of the three-dimensional carbon foam. X-ray diffraction (XRD) and Raman spectroscopy indicated that the obtained carbon foam was amorphous and of turbostratic structure. Moreover, the activation process enhanced the surface of the carbon foam, making it more hydrophilic via altering pore size distribution and introducing oxygen functional groups. In equilibrium, the adsorption of methylene blue on ACF followed the Langmuir isotherm model with a maximum adsorption capacity of 592 mg/g. Based on these results, the produced ACFs have potential applications as adsorbents, catalyst support and electrode material in energy storage systems.     

Crassolide Suppresses Dendritic Cell Maturation and Attenuates Experimental Antiphospholipid Syndrome

Antiphospholipid syndrome (APS) is an autoimmune disease characterized by the production of β2-glycoprotein I (β2GPI)-dependent autoantibodies, with vascular thrombosis or obstetrical complications. Around 20% of APS patients are refractory to current treatments. Crassolide, a cembranoid diterpene extracted from soft corals, is a potential therapeutic candidate. Here, to examine the anti-inflammatory properties of crassolide, we first determined its effects on bone marrow-derived and splenic dendritic cells (DC). Specifically, we applied lipopolysaccharide (LPS) or β2GPI stimulation and measured the expressions of CD80 and CD86, and secretions of cytokines. We also determined in the OT-II mice, if bone marrow-derived DC was able to stimulate antigen-specific T cells. Moreover, we examined the therapeutic potential of crassolide postimmunization in a murine model of APS that depended on active immunization with β2GPI. The vascular manifestations were evaluated in terms of fluorescein-induced thrombi in mesenteric microvessels, whereas the obstetric manifestations were evaluated based on the proportion of fetal loss after pregnancy. We also measured blood titers of anti-β2GPI antibody, splenic cell proliferative responses and cytokine secretions after β2GPI stimulation ex vivo. Finally, we determined in these mice, hematological, hepatic and renal toxicities of crassolide. Crassolide after LPS stimulation suppressed DC maturation and secretion of tumor necrosis factor (TNF)-α, interleukin (IL)-6, IL-12 and IL-23, and downstream T cell activation. Crassolide could partially ameliorate both the vascular and obstetric manifestations of APS in BALB/c mice. Both blood titers of anti-β2GPI antibody and splenic cell proliferation after β2GPI stimulation were reduced. Splenic Th1 and Th17 responses were also lowered after β2GPI stimulation. Finally, within therapeutic doses of crassolide, we found no evidence of its toxicity. In conclusion, we showed the ability of crassolide to suppress DC and downstream T cell responses. Crassolide is therefore a potential candidate for adjunctive therapy in APS.     

Actuating Shape Memory Polymer for Thermoresponsive Soft Robotic Gripper and Programmable Materials

For soft robotics and programmable metamaterials, novel approaches are required enabling the design of highly integrated thermoresponsive actuating systems. In the concept presented here, the necessary functional component was obtained by polymer syntheses. First, poly(1,10-decylene adipate) diol (PDA) with a number average molecular weight M_n of 3290 g·mol⁻¹ was synthesized from 1,10-decanediol and adipic acid. Afterward, the PDA was brought to reaction with 4,4′-diphenylmethane diisocyanate and 1,4-butanediol. The resulting polyester urethane (PEU) was processed to the filament, and samples were additively manufactured by fused-filament fabrication. After thermomechanical treatment, the PEU reliably actuated under stress-free conditions by expanding on cooling and shrinking on heating with a maximum thermoreversible strain of 16.1%. Actuation stabilized at 12.2%, as verified in a measurement comprising 100 heating-cooling cycles. By adding an actuator element to a gripper system, a hen’s egg could be picked up, safely transported and deposited. Finally, one actuator element each was built into two types of unit cells for programmable materials, thus enabling the design of temperature-dependent behavior. The approaches are expected to open up new opportunities, e.g., in the fields of soft robotics and shape morphing.     

Lignin as a Partial Polyol Replacement in Polyurethane Flexible Foam

This study was focused on evaluating the suitability of a wide range of lignins, a natural polymer isolated from different plant sources and chemical extractions, in replacing 20 wt.% of petroleum-based polyol in the formulation of PU flexible foams. The main goal was to investigate the effect of unmodified lignin incorporation on the foam’s structural, mechanical, and thermal properties. The hydroxyl contents of the commercial lignins were measured using phosphorus nuclear magnetic resonance (³¹P NMR) spectroscopy, molar mass distributions with gel permeation chromatography (GPC), and thermal properties with differential scanning calorimetry (DSC) techniques. The results showed that incorporating 20 wt.% lignin increased tensile, compression, tear propagation strengths, thermal stability, and the support factor of the developed PU flexible foams. Additionally, statistical analysis of the results showed that foam properties such as density and compression force deflection were positively correlated with lignin’s total hydroxyl content. Studying correlations between lignin properties and the performance of the developed lignin-based PU foams showed that lignins with low hydroxyl content, high flexibility (low T_g), and high solubility in the co-polyol are better candidates for partially substituting petroleum-based polyols in the formulation of flexible PU foams intended for the automotive applications.     

真空紫外光电离质谱技术进展及其在快速分析中的应用

真空紫外光电离源(VUV-PI)是一种普适性的质谱软电离源,真空紫外光电离质谱谱图无碎片、易解析、灵敏度高,适合于在线快速分析。真空紫外光电离质谱根据分析对象不同可以直接采用单光子电离或添加掺杂剂实现化学电离,能实现气、液、固体分析,也可实现成像分析。该文介绍了真空紫外光电离源的电离原理、光源类型,分析了光电离质谱灵敏度的影响因素及其技术改进措施,并阐述了真空紫外光电离质谱技术在环境污染物、化工产物在线分析、国家安全分析以及生物医学分析中的相关应用研究。最后,总结了真空紫外光电离源的优缺点,并对真空紫外光电离技术在性能和应用方面的发展前景进行了展望。     

Ni(OH)2修饰的三聚氰胺泡沫用于可压缩超级电容器电极

通过化学镀和电化学镀的方法制备了一种Ni(OH)₂电化学活性材料修饰三聚氰胺泡沫(MF)可压缩骨架的超级电容器电极材料MF/Ni(OH)₂。MF/Ni(OH)₂可压缩电极材料表现出最佳的电容性能,例如循环稳定性(即使在40 mA/cm^-3的电流密度下经过2000次充放电循环后,可压缩电极仍能保持90.63%的初始电容)和可压缩稳定性(即使在压缩率为50%时,仍具有97.88%的电容保持率)。层状可压缩超级电容器由MF/Ni(OH)₂弹性材料作为阳极,镍/碳(Ni/C)为阴极以及实验室中常用的滤纸作隔膜材料组成。这种超级电容器装置在不同的压缩下表现出良好的电化学性能和优异的压缩稳定性。最后,使用可压缩的超级电容器来点亮LED灯,以展示其在柔性电子设备中的应用。这些优化的电化学和机械性能表明MF/Ni(OH)₂可作为可压缩超级电容器的应用中的候选电极。     

Upgrade of beamline BL08B at Taiwan Light Source from a photon‐BPM to a double‐grating SGM beamline

During the last 20 years, beamline BL08B has been upgraded step by step from a photon beam‐position monitor (BPM) to a testing beamline and a single‐grating beamline that enables experiments to record X‐ray photo‐emission spectra (XPS) and X‐ray absorption spectra (XAS) for research in solar physics, organic semiconductor materials and spinel oxides, with soft X‐ray photon energies in the range 300–1000 eV. Demands for photon energy to extend to the extreme ultraviolet region for applications in nano‐fabrication and topological thin films are increasing. The basic spherical‐grating monochromator beamline was again upgraded by adding a second grating that delivers photons of energy from 80 to 420 eV. Four end‐stations were designed for experiments with XPS, XAS, interstellar photoprocess systems (IPS) and extreme‐ultraviolet lithography (EUVL) in the scheduled beam time. The data from these experiments show a large count rate in core levels probed and excellent statistics on background normalization in the L‐edge adsorption spectrum.     

糖厂澄清工段生产指标建模及操作参数优化

针对亚法糖厂澄清工段清汁色值和清汁残硫量难以在线测量的问题,提出了一种基于人工蜂群优化的在线极限学习机软测量方法。先用核主元分析法确定影响清汁质量的关键参数,建立基于在线极限学习机的软测量模型。同时利用人工蜂群算法对在线极限学习机的隐层参数进行寻优,优化所建模型。最后,使用带约束的粒子群对软测量模型进行优化求解,得到典型工况下的最优操作设定值,为后续工况操作提供参考依据。仿真结果表明,基于人工蜂群优化的在线极限学习机模型能够准确地预测清汁色值和残硫量,同时基于此模型优化的操作参数设定值能够达到期望的指标。