Optimizing the Photovoltaic Performance of Organic Solar Cells for Indoor Light Harvesting

Organic solar cells (OSCs) harvesting indoor light are highly promising for emerging technologies, such as internet of things. Herein, the photovoltaic performance of PTB7-Th:PC₇₁BM solar cells constructed using “optimized (with 1,8-diiodooctane (DIO))” and “non-optimized (without DIO)” processing conditions are compared for indoor and outdoor applications. We find that in comparison to the “optimized” solar cell, the “non-optimized” solar cell is less efficient under simulated solar light illumination (100 mW cm⁻², spectral range 350–1100 nm), owing to significant bimolecular charge carrier recombination losses. However, under simulated indoor illumination (3.28 mW cm⁻², spectral range 400–700 nm), bimolecular recombination losses are effective suppressed, thus the power conversion efficiency of the solar cell without DIO was increased to 14.7 %, higher than that of the solar cell with DIO (14.2 %). These results suggest that the common strategy used to optimize the OSCs could be undesired for indoor OSCs. We demonstrate that the efforts for realizing the desired “morphology” of the active layer for the outdoor OSCs may be unnecessary for indoor OSCs, allowing us to realize high-efficiency indoor OSCs using a non-halogenated solvent.     

CompassR Yields Highly Organic-Solvent-Tolerant Enzymes through Recombination of Compatible Substitutions

The CompassR (computer-assisted recombination) rule enables, among beneficial substitutions, the identification of those that can be recombined in directed evolution. Herein, a recombination strategy is systematically investigated to minimize experimental efforts and maximize possible improvements. In total, 15 beneficial substitutions from Bacillus subtilis lipase A (BSLA), which improves resistance to the organic cosolvent 1,4-dioxane (DOX), were studied to compare two recombination strategies, the two-gene recombination process (2GenReP) and the in silico guided recombination process (InSiReP), employing CompassR. Remarkably, both strategies yielded a highly DOX-resistant variant, M4 (I12R/Y49R/E65H/N98R/K122E/L124K), with up to 14.6-fold improvement after screening of about 270 clones. M4 has a remarkably enhanced resistance in 60 % (v/v) acetone (6.0-fold), 30 % (v/v) ethanol (2.1-fold), and 60 % (v/v) methanol (2.4-fold) compared with wild-type BSLA. Molecular dynamics simulations revealed that attracting water molecules by charged surface substitutions is the main driver for increasing the DOX resistance of BSLA M4. Both strategies and obtained molecular knowledge can likely be used to improve the properties of other enzymes with a similar α/β-hydrolase fold.     

Mechanism of Back Electron Transfer in an Intermolecular Photoinduced Electron Transfer Reaction: Solvent as a Charge Mediator

Back electron transfer (BET) is one of the important processes that govern the decay of generated ion pairs in intermolecular photoinduced electron transfer reactions. Unfortunately, a detailed mechanism of BET reactions remains largely unknown in spite of their importance for the development of molecular photovoltaic structures. Here, we examine the BET reaction of pyrene (Py) and 1,4‐dicyanobenzene (DCB) in acetonitrile (ACN) by using time‐resolved near‐ and mid‐IR spectroscopy. The Py dimer radical cation (Py₂^.+) and DCB radical anion (DCB^.?) generated after photoexcitation of Py show asynchronous decay kinetics. To account for this observation, we propose a reaction mechanism that involves electron transfer from DCB^.? to the solvent and charge recombination between the resulting ACN dimer anion and Py₂^.+. The unique role of ACN as a charge mediator revealed herein could have implications for strategies that retard charge recombination in dye‐sensitized solar cells.     

一种天线分子与卟啉染料自组装在染料敏化太阳能电池中的应用

以卟啉分子H2-pTCPP作为基础染料,通过配位自组装的方法将天线分子S3修饰到染料结构中。结果表明经天线分子修饰后染料敏化太阳能电池器件的整体性能得到了极大的改善。天线效应有效地提高了器件的光子捕获能力,光电流得到了显著的提高,并且电荷复合行为也得到了明显的抑制。基于H2-pTCPP的电池器件显示了1.18%的转换效率,而经过天线分子修饰后的Mn-pTCPP+S3显示了2.64%的转换效率,性能提高了1.2倍。     

热光伏能量转换器件的热力学极限与优化性能预测

受不可逆损失的影响,热光伏能量转换器件在高品位热能回收与利用方面受到限制.本文揭示不可逆损失来源,提供热光伏能量转换器件性能提升方案.利用半导体物理和普朗克热辐射理论,确定热光伏能量转换器件在理想条件下的最大效率.进而考虑Auger与Shockley-Reed-Hall非辐射复合和不可逆传热损失对光伏电池的电学、光学和热学特性的影响,预测热光伏器件优化性能.确定功率密度、效率和光子截止能量的优化区间.结果表明:相比于理想热光伏器件,非理想热光伏器件的开路电压、短路电流密度和效率有所降低;优化热光伏电池电压、光子截止能量和热源温度,可提升器件的功率密度和效率.通过对比发现理论与实验结果较一致,所得结果可为实际热光伏能量转换器件的研制提供理论指导.     

气体压强对纳秒激光诱导空气等离子体特性的影响

环境气体的压强对激光诱导等离子体特性有重要影响.基于发射光谱法开展了气体压强对纳秒激光诱导空气等离子体特性影响的研究,探讨了气体压强对空气等离子体发射光谱强度、电子温度和电子密度的影响.实验结果表明,在10-100 kPa空气压强条件下,空气等离子体发射光谱中的线状光谱和连续光谱依赖于气体压强变化,且原子谱线和离子谱线强度随气体压强的变化有明显差别.随着空气压强增大,激光击穿作用区域的空气密度增加,造成激光诱导击穿空气几率升高,从而等离子体辐射光谱强度增大.空气等离子体膨胀区域空气的约束作用,增加了等离子体内粒子间的碰撞几率以及能量交换几率,并且使离子-电子-原子的三体复合几率增加,因此造成原子谱线OⅠ777.2 nm与NⅠ821.6 nm谱线强度随着气体压强增大而增大,在80 kPa时谱线强度最高,随后谱线强度缓慢降低.而离子谱线N Ⅱ 500.5 nm谱线强度在40 kPa时达到最大值,气体压强大于40 kPa后,谱线强度随压强增加而逐渐降低.空气等离子体电子密度均随压强升高而增大,在80 kPa后增长速度变缓.等离子体电子温度在30 kPa时达到最大值,气体压强大于30 kPa后,等离子体电子温度逐渐降低.研究结果可为不同海拔高度的激光诱导空气等离子体特性的研究提供重要实验基础,为今后激光大气传输、大气组成分析提供重要的技术支持.     

Metamorphic InAs(Sb)/InGaAs/InAlAs nanoheterostructures grown on GaAs for efficient mid-IR emitters

High-efficiency semiconductor lasers and light-emitting diodes operating in the 3–5?μm mid-infrared (mid-IR) spectral range are currently of great demand for a wide variety of applications, in particular, gas sensing, noninvasive medical tests, IR spectroscopy etc. III-V compounds with a lattice constant of about 6.1?Å are traditionally used for this spectral range. The attractive idea to fabricate such emitters on GaAs substrates by using In(Ga,Al)As compounds is restricted by either the minimum operating wavelength of ～8?μm in case of pseudomorphic AlGaAs-based quantum cascade lasers or requires utilization of thick metamorphic In_xAl_1-xAs buffer layers (MBLs) playing a key role in reducing the density of threading dislocations (TDs) in an active region, which otherwise result in a strong decay of the quantum efficiency of such mid-IR emitters. In this review we present the results of careful investigations of employing the convex-graded In_xAl_1-xAs MBLs for fabrication by molecular beam epitaxy on GaAs (001) substrates of In(Ga,Al)As heterostructures with a combined type-II/type-I InSb/InAs/InGaAs quantum well (QW) for efficient mid-IR emitters (3–3.6?μm). The issues of strain relaxation, elastic stress balance, efficiency of radiative and non-radiative recombination at T?=?10–300?K are discussed in relation to molecular beam epitaxy (MBE) growth conditions and designs of the structures. A wide complex of techniques including in-situ reflection high-energy electron diffraction, atomic force microscopy (AFM), scanning and transmission electron microscopies, X-ray diffractometry, reciprocal space mapping, selective area electron diffraction, as well as photoluminescence (PL) and Fourier-transformed infrared spectroscopy was used to study in detail structural and optical properties of the metamorphic QW structures. Optimization of the growth conditions (the substrate temperature, the As₄/III ratio) and elastic strain profiles governed by variation of an inverse step in the In content profile between the MBL and the InAlAs virtual substrate results in decrease in the TD density (down to 3?×?10⁷ cm^?2), increase of the thickness of the low-TD-density near-surface MBL region to 250–300?nm, the extremely low surface roughness with the RMS value of 1.6–2.4?nm, measured by AFM, as well as rather high 3.5?μm-PL intensity at temperatures up to 300?K in such structures. The obtained results indicate that the metamorphic InSb/In(Ga,Al)As QW heterostructures of proper design, grown under the optimum MBE conditions, are very promising for fabricating the efficient mid-IR emitters on a GaAs platform.     

利用微生物直接生产羟基丁酸单体

利用重组大肠杆菌E.coli HB101来进行直接生产羟基丁酸(HB)手性单体,研究了含pUCAB质粒的重组体E.coli HB101在各种条件下生长及积累HB单体的情况,研究了HB单体的积累随pH值变化的规律。结果表明,pH=6.8时,48 h内细菌可生产0.5 g/L以上的HB单体。     

生物荧光方法快速测定环境水体中的甾体类激素

建立了环境中甾体类激素的生物荧光测定方法.利用睾丸酮丛毛单胞菌的生物酶基因与甾环结构特异的分子识别特性,结合绿色荧光蛋白(GFP)的荧光标记技术,通过基因同源重组技术建立了特异性生物荧光检测系统,实现对环境中甾环类化合物的灵敏监测.制备绿色荧光突变菌及总蛋白含量为1.0 g/L的非细胞体系工作液,在室温条件下对不同浓度雌二醇标准品进行检测,10 min即可检测出fg级的甾体类激素,最佳检测时间为30 min,方法的线性范围1.0～266 ng/L,灵敏度高于高效液相色谱方法.本方法可应用于环境的实际检验工作.     

锌掺杂对TiO2染料敏化电池光阳极中电荷俘获态分布及电子复合过程的影响

基于瞬态光电压和瞬态光电流技术研究了锌掺杂的TiO2染料敏化太阳能电池中电子复合及传输的动力学行为.通过实验获得了不同阳极掺杂条件下的电子复合时间常数与电子收集时间常数,考察了锌掺杂对电池阳极材料导带能级和电子俘获态的影响.研究结果表明,锌的掺杂在提高TiO2导带能级的同时延长了俘获态电子的复合时间常数,从而大大提高了电池的开路电压.