Stress State of Multilayer Thin-Walled Elements with Interfacial Defects of Structure

Based on the discrete-structural theory of thin plates and shells, a calculation model for thin-walled elements consisting of a number of rigid anisotropic layers is put forward. It is assumed that the transverse shear and compression stresses are equal on the interfaces. Elastic slippage is allowed over the interfaces between adjacent layers. The solution to the problem is obtained in a geometrically nonlinear statement with account of the influence of transverse shear and compression strains. The stress-strain state of circular two-layer transversely isotropic plates, both without defects and with a local area of adhesion failure at their center, is investigated numerically and experimentally. It is found that the kinematic and static contact conditions on the interfaces of layered thin-walled structural members greatly affect the magnitude of stresses and strains. With the use of three variants of calculation models, in the cases of perfect and weakened contact conditions between layers, the calculation results for circular plates are compared. It is revealed that the variant suggested in this paper adequately reflects the behavior of layered thin-walled structural elements under large deformations. __________ Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 6, pp. 761–772, November–December, 2005.     

Effects of Polymer Bridging and Electrostatics on the Rheological Behavior of Aqueous Colloidal Dispersions†

Effects of a low molecular weight physically adsorbed polyethylene oxide (PEO) and the range of the electrostatic repulsion on the rheological behavior of silica dispersions (as a model system) has been investigated. Particular attention is given to the evolution of the rheological behavior with increasing the polymer concentration in the system and also effectiveness of the polymer as a dispersant under extreme conditions (high ionic strength). Results indicate that at small separation distances and low polymer coverage, the polymer chains are long enough to adsorb on the surface of two particles simultaneously causing bridging flocculation in the system and hence increasing the viscosity and linear viscoelastic functions of the dispersion. A significant increase was observed in the viscosity of the dispersion at salt concentrations high enough to eliminate electrostatics between the particles. Under these conditions,the viscosity of the system increased significantly when PEO was added to the dispersion showing that at high electrolyte concentrations, a neutral polymer such as PEO is not able to stabilize the system.     

集中荷载下叠合梁抗剪强度

本文对低叠合面钢筋破简支在合梁二阶段受力的斜截面抗剪性能进行了试验研究，并运用非线性有限元分析和试验实测数据，得出了一个适合于集中荷载下高低叠合面叠合梁的抗剪强度计算公式．     

Foams and surface rheological properties of β-casein, gliadin and glycinin

Interfacial rheological properties and their suitability for foam production and stability of two vegetable proteins were studied and compared to β-casein. Proteins used ranged from flexible to rigid/globular in the order of β-casein, gliadin and soy glycinin. Experiments were performed at pH 6.7. Network forming properties were characterised by the surface dilational modulus (determined with the ring trough) and the critical falling film length (L_still) at which a stagnant protein film will break. Gliadin had the highest dilational modulus, followed by glycinin and β-casein, whereas glycinin formed the strongest film against fracture in the overflowing cylinder. The rate of decrease in the surface tension was studied at the air–water (Wilhelmy plate method) and the oil–water interface (bursting membrane) and the dynamic surface tension during compression and expansion in the caterpillar. Gliadin had the lowest equilibrium interfacial tensions and β-casein the lowest dynamic surface tension during expansion. Hardly any foam could be formed at a concentration of 0.1 g/l by shaking. At a concentration of 1.4 g/l most foam was formed by β-casein, followed by gliadin and glycinin. It seems that in the first place the rate of adsorption is important for foam formation. For the vegetable proteins, adsorption was slow. This resulted in lower foamability, especially for glycinin.     

A proof of Howard’s conjecture in homogeneous parallel shear flows

A rigorous mathematical proof of Howard's conjecture which states that the growth rate of an arbitrary unstable wave must approach zero, as the wave length decreases to zero, in the linear instability of nonviscous homogeneous parallel shear flows, is presented here for the first time under the restriction of the boundedness of the second derivative of the basic velocity field with respect to the vertical coordinate in the concerned flow domain.     

Separation of screw-sensed particles in a homogeneous shear field

The Stokes motions of three-dimensional screw-sensed slender particles in a homogeneous shear field are investigated, including the effects of buoyancy. Conclusions are drawn about the possibility of achieving a separation of mixtures of right- and left-handed particles. The linearity of the Stokes equations allows complex flows to be solved by adding the effects of the several terms which describe the flow in which the particle is immersed. The homogeneous shear flow considered here consists of three such terms; solutions for a series of 12 unit motions are sufficient to determine the hydrodynamic resistance tensors. The forces and torques experienced by screw-sensed particles are calculated from these 51 resistance tensors, using slender-filament theory. The results allow an estimate of the range of buoyancy parameters for which gravitational sedimentation can be neglected. The fundamental component of the particle motion is a rotation, at approximately the same angular velocity as that of the fluid. Superimposed on this are variations, of large period, in the particle orientation. A phase plane analysis is used to find the terminal orientations. Very long calculation times are required for the phase portrait. An approximate method based on azimuthally-averaged equations is developed to avoid the requirements for long time integration.     

The effect of nanoparticle shape on polymer‐nanocomposite rheology and tensile strength

Nanoparticles can influence the properties of polymer materials by a variety of mechanisms. With fullerene, carbon nanotube, and clay or graphene sheet nanocomposites in mind, we investigate how particle shape influences the melt shear viscosity η and the tensile strength τ, which we determine via molecular dynamics simulations. Our simulations of compact (icosahedral), tube or rod‐like, and sheet‐like model nanoparticles, all at a volume fraction ? ≈ 0.05, indicate an order of magnitude increase in the viscosity η relative to the pure melt. This finding evidently can not be explained by continuum hydrodynamics and we provide evidence that the η increase in our model nanocomposites has its origin in chain bridging between the nanoparticles. We find that this increase is the largest for the rod‐like nanoparticles and least for the sheet‐like nanoparticles. Curiously, the enhancements of η and τ exhibit opposite trends with increasing chain length N and with particle shape anisotropy. Evidently, the concept of bridging chains alone cannot account for the increase in τ and we suggest that the deformability or flexibility of the sheet nanoparticles contributes to nanocomposite strength and toughness by reducing the relative value of the Poisson ratio of the composite. The molecular dynamics simulations in the present work focus on the reference case where the modification of the melt structure associated with glass‐formation and entanglement interactions should not be an issue. Since many applications require good particle dispersion, we also focus on the case where the polymer‐particle interactions favor nanoparticle dispersion. Our simulations point to a substantial contribution of nanoparticle shape to both mechanical and processing properties of polymer nanocomposites. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1882–1897, 2007     

An unflexural refined model of deformation of multilayered plates on an undeformable foundation

The stress-strain state of multilayered plates on an undeformable foundation is investigated. The design diagram of a transversely loaded plate is formed by supplementing it with a symmetric one about the contact surface of the foundation. The double-thickness plate obtained becomes loaded bilaterally and symmetrically about its midsurface. In such a way, only unflexural deformations can be modeled, which reduces the number of unknowns and the general order of differentiation of the resolving system of equations. The refined continual model developed takes into account the deformations of transverse shear and transverse compression in high iterative approximations. The cases of a rigid contact between the foundation and the plate and frictionless slip of the plate over the foundation are considered. Calculations confirm the efficiency of such an approach, which allows one to obtain solutions qualitatively and quantitatively close to three-dimensional ones. __________ Translated from Mekhanika Kompozitnykh Materialov, Vol. 42, No. 5, pp. 643–654, September–October, 2006.     

切变模量和转动惯量实验的改进

设计了一种基于垂直轴定理的新型吊钩,对切变模量和转动惯量实验进行了改进,使之成为既可测定金属丝切变模量和环、柱等刚体的转动惯量,又可验证反映转动惯量重要性质的平行轴定理及垂直轴定理的多功能实验仪.     

透镜初级球差的横向剪切干涉条纹研究

利用玻璃平行平板构成简单的横向剪切干涉仪可以观察到单薄透镜形成的准直光束的剪切干涉条纹,由干涉条纹分布求出对应的几何像差和离焦量.用焦距为190 mm的单薄透镜做实验,实验结果与计算机模拟结果符合,说明可以从剪切干涉条纹的分布求出透镜的轴向调整误差和初级球差.