Development and validation of a capillary electrophoresis method for the determination of phenothiazines in human urine in the low nanogram per milliliter concentration range using field-amplified sample injection

A capillary zone electrophoresis (CZE) method with ultraviolet-visible detection has been established and validated for the determination of five phenothiazines: thiazinamium methylsulfate, promazine hydrochloride, chlorpromazine hydrochloride, thioridazine hydrochloride, and promethazine hydrochloride in human urine. Optimum separation was obtained on a 64.5 cm x 75 microm bubble cell capillary using a buffer containing 150 mM tris(hydroxymethyl)aminomethane and 25% acetonitrile at pH 8.2, with temperature and voltage of 25 degrees C and 20 kV, respectively. Naphazoline hydrochloride was used as an internal standard. Field-amplified sample injection (FASI) has been applied to improve the sensitivity of the detection. Considering the influence of parameters affecting the on-line preconcentration (nature of preinjection plug, sample solvent composition, injection times, and injection voltage) and due to the significant interactions among them, in this paper we propose for the first time the application of a multivariate approach to carry out the study. The optimized conditions were as follows: preinjection plug of water for 7 s at 50 mbar, electrokinetic injection for 40 s at 6.2 kV, and 32 microm of H3PO4 in the sample solvent. Also, a solid-phase extraction (SPE) procedure is developed to obtain low detection limits and an adequate selectivity for urine samples. The combination of SPE and FASI-CZE-UV allows adequate linearities and recoveries, low detection limits (from 2 to 5 ng/mL), and satisfactory precisions (3.0-7.2% for an intermediate RSD %).     

Developing a sequential injection-square wave voltammetry (SI-SWV) method for determination of atrazine using a hanging mercury drop electrode

This paper describes the development of a sequential injection analysis method to automate the determination of atrazine by square wave voltammetry exploiting the concept of monosegmented flow analysis to perform in-line sample conditioning and standard addition. To perform these tasks, an 800 μL monosegment is formed, composed by 400 μL of sample and 400 μL of buffer/standard solution. To obtain an efficient homogenization, the sample solution is divided in five zones intercalated by four zones of the Britton-Robinson buffer (pH 2.0) in presence of appropriate concentration of NaNO₃ and varying atrazine standard concentrations. This mixture zone is isolated from the carrier solution by two 100 μL air bubbles. After homogenization in an auxiliary reaction coil the mixture zone is injected toward the flow cell, which is adapted to the capillary of a hanging drop mercury electrode, at a flow rate of 50 μL s⁻¹. After a suitable delay time, the potential is scanned from −0.5 to −1.2 V versus Ag/AgCl using a frequency of 300 Hz and pulse height of 25 mV. The linear dynamic range is observed for atrazine concentrations between 1.16 × 10⁻⁷ and 2.32 × 10⁻⁶ mol L⁻¹, obeying the linear equation i_p = (−6.91 ± 0.07) × 10⁸[atrazine] + (4 ± 8), with r² = 0.9996, for which the slope is given in nA L mol⁻¹. The detection and quantification limits of the method are 2.1 × 10⁻⁸ and 7.0 × 10⁻⁸ mol L⁻¹, respectively. The sampling frequency is 37 h⁻¹, when the standard addition protocol is followed. This frequency can be increased to 42 h⁻¹ if the protocol to obtain in-line calibration curve is used for quantification. The method was applied for determination of atrazine in spiked river water samples and its accuracy was evaluated by comparison with the batch standard addition approach, which revealed that there is no evidence of statistically significant differences between the two methods.     

Evaluation of the calibration errors on cooling of a differential scanning calorimeter using different sets of standard metals

The temperature calibration on cooling of thermal analysis instruments is important for the accurate study of the non-isothermal crystallization kinetics of semi-crystalline polymers. In previous works, a methodology was proposed for performing the calibration on cooling of differential scanning calorimeters (DSCs) with standard metals, and the calibration errors were checked using transitions of high-purity liquid crystals. In this work, alternative, physically meaningful, procedures for carrying out the calibration on cooling are analyzed and validated. The calibration errors are evaluated also with liquid crystalline transitions, when the calibration is performed with standard metals, in a wide temperature range, and when due account is taken for the need of isothermal corrections to the temperature measurements. It is shown that any pair of standard metals may be used to calibrate on cooling, that the calibration errors increase for wider working temperature ranges and that, providing that certain conditions are fulfilled, both calibration procedures yield similar results.     

FTIR studies of polyimides. II. Factors affecting quantitative measurement

Measurement of imidization by IR spectroscopy has frequently been reported to give results that are either insensitive to changes in the latter part of the cure or in conflict with observations by other methods. However, an analysis of imide formation using the 1370 cm^?1 band (C? N stretch) in conjunction with the 1500 cm^?1 aromatic band as an internal standard appears capable of giving precise, internally consistent measurements for the most commonly used polyimide structures, for samples that are measured in transmission. Measurements of imide content in ultrathin films by grazing incidence reflection spectroscopy appear to be at least semiquantitative. © 1993 John Wiley & Sons, Inc.     

X—射线荧光光谱测定甜饮料中微量元素

本文提出了低温蒸干和炭化制样Ｘ－射线荧光分析甜饮料中１６种微量元素的方法，试样在电热板上经低温蒸干，于马旨炉中３００℃炭化３０ｍｉｎ，在液压样品成形机上压制成样片进行测定，所测元素不需用任何基体校正，由微机从校正曲线查得含量，榈分析结果与ＩＣＰ－ＡＥＳ和ＡＡＳ法相吻合。     

Single‐Wall Carbon Nanotube Paste Electrodes: a Comparison with Carbon Paste,Platinum and Glassy Carbon Electrodes via Cyclic Voltammetric Data

A new carbon electrode material, obtained by mixing single wall carbon nanotubes (SWNTs) with a mineral oil binder is studied. Carbon nanotube pastes show the special properties of carbon nanotubes combined with the various advantages of composite electrodes such as a very low capacitance (background current) and the possibility of an easy preparation, modification and renewal. A better knowledge of the characteristics of electrode reactions at carbon nanotube paste (CNTP) electrodes was obtained studying the electron transfer rates of various redox couples under different pretreatment conditions. A critical comparison with carbon paste (CP), platinum (Pt) and glassy carbon (GC) electrodes was also carried out. Capacitance and resistance values were also calculated for all electrodes investigated. Both untreated and treated CNTP electrodes showed a low resistance while the capacitance was markedly reduced with CNTP electrodes previously treated with concentrated nitric acid. An electrochemical pretreatment on CNTP electrodes was developed which showed an excellent result towards two‐electron quinonic structure species. After this treatment the heterogeneous standard rate constants for p‐methylaminophenol sulfate (MAP) and dopamine resulted to be significantly higher (2.1×10^?2 cm/s and 2.0×10^?2 cm/s, respectively) than those obtained with the other electrodes studied. Reproducibility, stability and storage characteristics of CNTP electrodes were also reported.     

微克级介形虫壳体样品的多元素ICP－AES同时测定

本文从顺序扫描式双通道电感耦合等离子体原子发射光谱仪（ＩＣＰ－ＡＥＳ）的特点出发，对微克级介形虫壳体样品中的低含量元素选择最灵敏谱线和最佳通道，对各项条件进行最优化。Ｍｇ、Ｓｒ、Ｍｎ、Ｆｅ、Ｂａ、Ｚｎ的检测限分别为０．６～５．２μｇ／Ｌ，Ｃａ和Ｎａ的检测限分别为１６μｇ／Ｌ和５２μｇ／Ｌ，测定了微克级样品的多元素含量，回收率为９０％～１０６％。     

废弃线路板化学分析采样、制样及检测方法

介绍废弃线路板中有回收价值元素和有害物质分析的采样、制样及检测技术。样品经过分类采样、剪切破碎和高温灰化制样,采用样品全分析或副批混合样分析。通过提高称样量、多次测定求平均值的办法,火试金富集-重量法测定贵金属金、银。湿法王水溶解样品,碘量法测定主体元素铜。电感耦合等离子体发射光谱(ICP-AES)法测定其它杂质元素,被测元素质量浓度在0~10μg/mL范围内与光谱强度呈良好线性关系,相关系数均大于0.9998。测定结果的相对标准偏差小于10%(n=5),加标回收率为97.0%~102.5%。该方法简单、快速,有效地解决了线路板样品不均匀而难采样,以及硬度、韧性强制样难,金属易包裹难分解的技术瓶颈,测定结果准确,具有代表性。该方法适用于废弃线路板化学成分分析,其它废弃电子产品检测可参考此方法。     

Strategies to enhance the enzymatic hydrolysis of pretreated softwood with high residual lignin content

Pretreatment of Douglas-fir by steam explosion produces a substrate containing approx 43% lignin. Two strategies were investigated for reducing the effect of this residual lignin on enzymatic hydrolysis of cellulose: mild alkali extraction and protein addition. Extraction with cold 1% NaOH reduced the lignin content by only approx 7%, but cellulose to glucose conversion was enhanced by about 30%. Before alkali extraction, addition of exogenous protein resulted in a significant improvement in cellulose hydrolysis, but this protein effect was substantially diminished after alkali treatment. Lignin appears to reduce cellulose hydrolysis by two distinct mechanisms: by forming a physical barrier that prevents enzyme access and by non-productively binding cellulolytic enzymes. Cold alkali appears to selectively remove a fraction of lignin from steam-exploded Douglas-fir with high affinity for protein. Corresponding data for mixed softwood pretreated by organosolv extraction indicates that the relative importance of the two mechanisms by which residual lignin affects hydrolysis is different according to the pre- and post-treatment method used.