Implementation and efficiency of an automatic peak-purity-control procedure in HPLC-UV-VIS-coupling based on principal component analysis

Summary Based on a thorough knowledge of the actual system precision significance testing of the primary eigen values, resulting from principal component analysis of the two-dimensional data array of HPLC with photodiode-array detection, is a powerful means to uncover unresolved chromatographic peaks. The implementation of this chemometric technique for assuring peak homogeneity and results showing the efficiency for two-component peaks in regard to spectral characteristics, chromatographic resolution and absorbance ratio of the investigated compounds are presented.     

微色谱柱分离/ICP-AES测定环境样品中的痕量硼

本文采用色谱系统对水样品（温泉水、卤水）中的硼进行分离富集，探讨了影响其分离富集的条件。实验表明，在pH＝8条件下，硼可被树脂完全吸附，用3mL 1mol/L硫酸可以从吸附术上完全解吸硼，浓缩物用ICP－AES进行测定，所建立的方法简便、准确，适合于含盐量高及其它水样品中微量硼的测定。     

Development and validation of a capillary electrophoresis method for the determination of phenothiazines in human urine in the low nanogram per milliliter concentration range using field-amplified sample injection

A capillary zone electrophoresis (CZE) method with ultraviolet-visible detection has been established and validated for the determination of five phenothiazines: thiazinamium methylsulfate, promazine hydrochloride, chlorpromazine hydrochloride, thioridazine hydrochloride, and promethazine hydrochloride in human urine. Optimum separation was obtained on a 64.5 cm x 75 microm bubble cell capillary using a buffer containing 150 mM tris(hydroxymethyl)aminomethane and 25% acetonitrile at pH 8.2, with temperature and voltage of 25 degrees C and 20 kV, respectively. Naphazoline hydrochloride was used as an internal standard. Field-amplified sample injection (FASI) has been applied to improve the sensitivity of the detection. Considering the influence of parameters affecting the on-line preconcentration (nature of preinjection plug, sample solvent composition, injection times, and injection voltage) and due to the significant interactions among them, in this paper we propose for the first time the application of a multivariate approach to carry out the study. The optimized conditions were as follows: preinjection plug of water for 7 s at 50 mbar, electrokinetic injection for 40 s at 6.2 kV, and 32 microm of H3PO4 in the sample solvent. Also, a solid-phase extraction (SPE) procedure is developed to obtain low detection limits and an adequate selectivity for urine samples. The combination of SPE and FASI-CZE-UV allows adequate linearities and recoveries, low detection limits (from 2 to 5 ng/mL), and satisfactory precisions (3.0-7.2% for an intermediate RSD %).     

Cadmium speciation in Arabidopsis thaliana as a strategy to study metal accumulation system in plants

The strategy to identify cadmium deactivation mechanism in Arabidopsis thaliana has been developed using selective and sensitive hyphenated techniques. Cadmium concentrations, in main parts of the plant, were determined by ICP-MS and total amount was found as 0.43-0.44 μg g⁻¹ in leaves and 3.3-3.4 μg g⁻¹ in roots. Speciation of the metal complexes in cells was investigated by SEC-ICP-MS in order to estimate the accumulation process. Phytochelatins, desglycyl-phytochelatins and phytochelatins homologues lacking the N-terminal γ-linked glutamic acid were extracted from plant and were identified by RPLC-ESI-MS. Two-dimensional chromatography allowed to link the metal complexes separated by SEC with isoforms of phytochelatins analyzed by high resolution RPLC and confirm their significant responsibility for metal accumulation. The potential of the cadmium complexes speciation indicates that obtained results could be reliable source of knowledge to confirm the information coming from the well-known genomic sequence of Arabidopsis and to estimate the role of γ-glutamyl transpeptidase in metabolism of glutathione.     

Sample preparation in analysis of pharmaceuticals

Sample preparation is a very important and essential step in environmental analysis. This article presents an overview of extraction methods for environmental samples, focusing especially on pharmaceuticals as there is great concern about them as pollutants.     

原子吸收光谱法测定拉伸断口铬镍钼钛钢样品中主成分

研究了毫克级铬镍钼风样品中主成分镍的火焰原子吸收光谱法（FAAS法）和铬、钼、钒、钛、铝的塞曼恒温平台石墨炉原子吸收光谱法（ZSTPF－AAS法）。采用了微波溶样技术作为防污染样品预处理技术，采用石墨管硅涂层改进技术提高了仪器的测试精度。其中铬、镍、钼、钒、钛、铝的相对标准偏差分别为2.7%,0.97%,8.6%,7.3%,1.7%,7.3%。其加标回收率分别为96.5%,97%,96.7%,93%,98%,91%。通过分析，发现在较低温度下铬镍钼钛钢断面上有轻微的钼偏析现象，可能是拉伸断裂的主要化学影响因素。     

Developing a sequential injection-square wave voltammetry (SI-SWV) method for determination of atrazine using a hanging mercury drop electrode

This paper describes the development of a sequential injection analysis method to automate the determination of atrazine by square wave voltammetry exploiting the concept of monosegmented flow analysis to perform in-line sample conditioning and standard addition. To perform these tasks, an 800 μL monosegment is formed, composed by 400 μL of sample and 400 μL of buffer/standard solution. To obtain an efficient homogenization, the sample solution is divided in five zones intercalated by four zones of the Britton-Robinson buffer (pH 2.0) in presence of appropriate concentration of NaNO₃ and varying atrazine standard concentrations. This mixture zone is isolated from the carrier solution by two 100 μL air bubbles. After homogenization in an auxiliary reaction coil the mixture zone is injected toward the flow cell, which is adapted to the capillary of a hanging drop mercury electrode, at a flow rate of 50 μL s⁻¹. After a suitable delay time, the potential is scanned from −0.5 to −1.2 V versus Ag/AgCl using a frequency of 300 Hz and pulse height of 25 mV. The linear dynamic range is observed for atrazine concentrations between 1.16 × 10⁻⁷ and 2.32 × 10⁻⁶ mol L⁻¹, obeying the linear equation i_p = (−6.91 ± 0.07) × 10⁸[atrazine] + (4 ± 8), with r² = 0.9996, for which the slope is given in nA L mol⁻¹. The detection and quantification limits of the method are 2.1 × 10⁻⁸ and 7.0 × 10⁻⁸ mol L⁻¹, respectively. The sampling frequency is 37 h⁻¹, when the standard addition protocol is followed. This frequency can be increased to 42 h⁻¹ if the protocol to obtain in-line calibration curve is used for quantification. The method was applied for determination of atrazine in spiked river water samples and its accuracy was evaluated by comparison with the batch standard addition approach, which revealed that there is no evidence of statistically significant differences between the two methods.     

Evaluation of the calibration errors on cooling of a differential scanning calorimeter using different sets of standard metals

The temperature calibration on cooling of thermal analysis instruments is important for the accurate study of the non-isothermal crystallization kinetics of semi-crystalline polymers. In previous works, a methodology was proposed for performing the calibration on cooling of differential scanning calorimeters (DSCs) with standard metals, and the calibration errors were checked using transitions of high-purity liquid crystals. In this work, alternative, physically meaningful, procedures for carrying out the calibration on cooling are analyzed and validated. The calibration errors are evaluated also with liquid crystalline transitions, when the calibration is performed with standard metals, in a wide temperature range, and when due account is taken for the need of isothermal corrections to the temperature measurements. It is shown that any pair of standard metals may be used to calibrate on cooling, that the calibration errors increase for wider working temperature ranges and that, providing that certain conditions are fulfilled, both calibration procedures yield similar results.     

FTIR studies of polyimides. II. Factors affecting quantitative measurement

Measurement of imidization by IR spectroscopy has frequently been reported to give results that are either insensitive to changes in the latter part of the cure or in conflict with observations by other methods. However, an analysis of imide formation using the 1370 cm^?1 band (C? N stretch) in conjunction with the 1500 cm^?1 aromatic band as an internal standard appears capable of giving precise, internally consistent measurements for the most commonly used polyimide structures, for samples that are measured in transmission. Measurements of imide content in ultrathin films by grazing incidence reflection spectroscopy appear to be at least semiquantitative. © 1993 John Wiley & Sons, Inc.     

X—射线荧光光谱测定甜饮料中微量元素

本文提出了低温蒸干和炭化制样Ｘ－射线荧光分析甜饮料中１６种微量元素的方法，试样在电热板上经低温蒸干，于马旨炉中３００℃炭化３０ｍｉｎ，在液压样品成形机上压制成样片进行测定，所测元素不需用任何基体校正，由微机从校正曲线查得含量，榈分析结果与ＩＣＰ－ＡＥＳ和ＡＡＳ法相吻合。