Temperature-controlled combustion and kinetics of different rank coal samples

Differential scanning calorimetry (DSC) and thermogravimetry (TG/DTG) has been used to obtain information on the temperature-controlled combustion characteristics of seventeen coals of different origin from Thrace basin of Turkey. Experiments were performed in air atmosphere up to 600°C at a heating rate of 10°C min^-1. The DSC/TG curves clearly demonstrate distinct transitional stages in the entire coal samples studied. Reaction intervals, peak and burn-out temperatures of the coal samples are also determined. Two different kinetic methods known as, Arrhenius and Coats-Redfern, were used to analyze the kinetic data and the results are discussed.     

Crystallization and melting behaviors of polystyrene-b-poly(ethylene-co-butene) block copolymers

Non-isothermal and isothermal crystallization behaviors of polystyrene-b-poly(ethylene-co-butene) (PSt-b-PEB) block copolymers with different compositions and chain lengths were investigated by differential scanning calorimetry (DSC). The results show that crystallization of PEB block is strongly dependent on the composition. Crystallization temperature (T_c), melting temperature (T_m) and fusion enthalpy (ΔH_f) increase rapidly with PEB volume fraction (V_E) for block copolymers with V_E below 50%, but there is little change when PEB block becomes the major component. Glass transition temperature (T_g) of the PSt block and order-disorder transition temperature (T_ODT) of block copolymers also have a weak effect. The isothermal crystallization kinetics results show that Avrami exponent (n) was strongly dependent on the composition and crystallization temperature. For the block copolymers with V_E below 38.7 vol%, the values of n vary between 0.9 and 1.3, indicating that crystallization is confined. For the PSt-b-PEB block copolymers with V_E higher than 50%, fractionated crystallization behavior is usually observed. A two-step isothermal crystallization procedure is applied to these block copolymers. It is found that breakout crystallization occurs at higher T_c, but confined at lower T_c. Two overlapped melting peaks are observed for the block copolymers with fractionated crystallization behavior after two-step crystallization, and only the higher melting peak corresponding to breakout crystallization can be used to derive equilibrium melting temperature.     

碳纳米管在接枝二元胺过程中微结构的变化

通过对酸化的多壁碳纳米管(MWNTs)进行酰氯化, 在碳纳米管表面接枝己二胺. 用红外光谱、热重分析、拉曼光谱和场发射扫描电镜对处理前后的碳纳米管进行分析表征. 结果表明, 经过酰氯活化, 己二胺比较容易被接枝到碳纳米管上. 而且还发现碳纳米管在酸化后形成紧密块状结构, 在接枝胺后重新变得蓬松, 其表观比容甚至大于原始碳纳米管. 从理论上分析了碳纳米管的反应过程, 对碳纳米管在接枝胺过程中微结构的变化机理进行推测, 认为通过接枝, 己二胺插入碳纳米管之间, 改变了碳纳米管之间的相互作用, 使得酸化后因形成氢键而导致的紧密堆砌结构被破坏.     

Study of poly(bisphenol A carbonate) relaxation kinetics at the glass transition temperature

In this work, the variations of the relaxation times are investigated above and below the glass transition temperature of a model amorphous polymer, the polycarbonate. Three different techniques (calorimetric, dielectric and thermostimulated currents) are used to achieve this goal. The relaxation time at the glass transition temperature was determined at the temperature dependence convergence of the relaxation times calculated with dynamic dielectric spectroscopy (DDS) for the liquid state and thermostimulated depolarisation currents (TSDC) for the vitreous state. We find a value of τ(T_g) = 110 s for PC samples. The knowledge of the temperature dependence, τ(T), and the value τ(T_g) enables to determine the glass-forming liquid fragility index, m. We find m = 178 ± 5.     

Evaluation of thermodynamic properties of irreversible protein thermal unfolding measured by DSC

Summary We assessed the applicability of the extrapolation procedure at infinite scanning rate to differential scanning calorimetry (DSC) data related to irreversible protein unfolding. To this aim, an array of DSC curves have been simulated on the basis of the Lumry-Eyring model N↔U→F. The results obtained confirmed that when the apparent equilibrium constant K_{app (T=T1/2)} is lower than 3, the application of the extrapolation procedure provides accurate thermodynamic parameters. Although this procedure applies only to monomeric proteins for which the Lumry-Eyring model is a reasonable approximation, it will hopefully contribute to increase the potential of DSC in obtaining reliable thermodynamic information regarding the folding/unfolding equilibrium.     

Crystallization of poly(N-methyldodecano-12-lactam) in blends with poly(styrene-stat-acrylic acid)

Crystallization behaviour of blends of poly(N-methyldodecano-12-lactam) (PMDL) with statistical copolymer poly(styrene-stat-acrylic acid) (PSAA) has been studied by the DSC and WAXD methods. The blend films prepared from dioxane solutions were crystallized at laboratory temperature for five days. Approximate crystallinities of as-prepared neat lower- PMDL 5 and higher-molecular weight PMDL 45 were 28% and 19%, respectively. With increasing PSAA content in the blends the crystallinities decreased sharply. The melting point of the primary crystalline structure of PMDL showed a decreasing dependence on PSAA content in the blends, confirming miscibility of the PMDL-PSAA pair. Recrystallization was strongly suppressed in the blends. The lower-melting endotherm appearing at about 10-15 °C above the crystallization temperature was attributed to melting to less perfect structures formed during secondary crystallization. In neat PMDL, the extent of secondary crystallization was approximately 5-10%. In the blends containing 20% PSAA approximate relative proportion of secondary crystallites on total crystallinity was 40% and 60% for the blends with PMDL 5 and PMDL 45, respectively. WAXD measurements did not reveal any change in crystal modification on blending. Increased T_g in blends of flexible PMDL cannot play a significant role in suppression of primary in favour of secondary crystallization. This was attributed to low mobility of PMDL chains due to dilution effect and specific interactions with the amorphous copolymer component, and, in case of the higher-molecular-weight PMDL, a greater involvement of entanglements. Higher T_g of blends was involved in retardation of non-isothermal crystallization on cooling and subsequent cold crystallization.     

Self-assembly of amphiphilic hexapyridinium cations at the air/water interface and on HOPG surfaces.

Mono- and multilayers of a novel amphiphilic hexapyridinium cation with six eicosyl chains (3) are spread at the air/water interface as well as on highly ordered pyrolytic graphite (HOPG). On water, the monolayer of 3 is investigated by recording surface pressure/area and surface potential/area isotherms, and by Brewster angle microscopy (BAM). Self-organized tubular micelles with an internal edge-on orientation of molecules form at the air/water interface at low surface pressure whereas multilayers are present at high surface pressure, after a phase transition. Packing motifs suggesting a tubular arrangement of the constituting molecules were gleaned from atomic force microscopy (AFM) investigations of Langmuir-Blodgett (LB) monolayers being transferred on HOPG at different surface pressures. These LB film structures are compared to the self-assembled monolayer (SAM) of 3 formed via adsorption from a supersaturated solution, which is studied by scanning tunnelling microscopy (STM). On HOPG the SAM of 3 consists of nanorods with a highly ordered edge-on packing of the aromatic rings and an arrangement of alkyl chains which resembles the packing of molecules at the air/water interface at low surface pressure. Additional details of the molecular packing were gleaned from single-crystal X-ray structure analysis of the hexapyridinium model compound 2b, which possesses methyl instead of eicosyl residues.     

Pyrolysis Analysis and Kinetics of Crude Oils

This research presents the results of an experimental study on the determination of pyrolysis behaviour and kinetics of six crude oils by differential scanning calorimetry (DSC) and thermogravimetry (TG/DTG). Crude oil pyrolysis indicated two main temperature ranges where loss of mass was observed. The first region between ambient to 400°C was distillation. The second region between 400 and 600°C was visbreaking and thermal cracking. Arrhenius-type kinetic model is used to determine the kinetic parameters of crude oils studied. It was observed that as crude oils gets heavier (°API decreases) cracking activation energy increases. Activation energy of cracking also show a general trend with asphaltene content. This revised version was published online in July 2006 with corrections to the Cover Date.     

Ionic liquid–modified cellulosic hydrogels for loading and sustained release of selenourea: an ensuing inhibition of tyrosinase activity

Cellulose-based hydrogel materials were prepared and modified with tannic acid and l-methionine using ionic liquid as the solvent. The gels were prepared to develop a sustained release medium for selenourea (SeU). The drug delivery characteristics of selenourea-loaded cellulose (CSeU), selenourea-loaded tannic acid-modified cellulose (CTSeU), and selenourea-loaded L-methionine-modified cellulose (CMSeU) were investigated in aqueous media and simulated gastric fluid (SGF) media. This modified gel beads have been characterized using field emission scanning electron microscope, X-ray energy-dispersive spectroscopy, Fourier transform infrared spectroscopy, thermogravimetry–differential thermal analysis and swelling properties and compared with those of the unmodified ones. We also investigated the inhibitory effects of SeU released from these gels on the activity of mushroom tyrosinase. Out of all the gel materials, CTSeU showed maximum SeU release both in water and SGF media. However, tyrosinase inhibitory action in PBS medium was comparable for all the three gel materials.     

Large‐scale extrusion processing and characterization of hybrid nylon‐6/SiO2 nanocomposites

Solution impregnations, pulltrusion and film stacking are widely used methods to prepare thermoplastic composite materials. Extruders are used to melt the polymer and to incorporate fibers into the polymer in order to modify physical properties. In this article, the compounding of colloidal silica nanoparticles filled polyamide‐6 (PA‐6) is achieved using a twin‐screw extruder, which has a significant market share due to its low cost and easy maintenance. The experiments were performed at 250 rpm and the bulk throughput was 6 kg h^?1 with a pump pressure of 30 bars. The composites were characterized with nuclear magnetic resonance (NMR), wide angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC) and transmission electron microscopy (TEM). As determined by WAXD, the PA‐6 showed higher amounts of γ‐phase when compared to other synthesis methods such as in situ polymerization. TEM pictures showed that the silica particles aggregated nevertheless, upon addition of 14% (w/w) silica the E‐modulus increased from 2.7 to 3.9 GPa indicating that an effective mechanical coupling with the polymer was achieved. The behavior, illustrated with dynamic mechanical analysis (DMA) curves, indicated that in general when a filled system is compared to unfilled material, the values of the moduli (E′ and E″) increased and tan δ decreased. Determination of molecular mass distribution of the samples by means of size exclusion chromatography (SEC) coupled to a refractive index (RI), viscosity (DV) and light scattering (LS) detector revealed that the addition of silica did not decrease the average molecular weight of the polymer matrix, which is of importance for composite applications. Copyright © 2004 John Wiley & Sons, Ltd.