Ultra‐high molecular weight styrenic block copolymer/TPU blends for automotive applications: Influence of various compatibilizers

Thermoplastic elastomers (TPEs) based on new generation ultrahigh molecular weight styrene‐ethylene‐butylene‐styrene (SEBS) and thermoplastic polyurethane (TPU) are developed and characterized especially for automotive applications. Influence of maleic anhydride grafted styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MA) and maleic anhydride grafted ethylene propylene rubber (EPM‐g‐MA) as compatibilizers has been explored and compared on the blends of SEBS/TPU (60:40). The amount of compatibilizers was varied from 0 to 10 phr. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) studies revealed the dramatic changes from a nonuniform to finer and uniform dispersed phase morphology. This was reflected in various mechanical properties. SEBS‐g‐MA modified blends showed higher tensile strength. EPM‐g‐MA modified blends also displayed considerable improvement. Elongation at break (EB) was doubled for the entire compatibilized blends. Fourier‐transform infrared spectrometry (FTIR) confirmed the chemical changes in the blends brought about by the interactions between blend components and compatibilizers. Both SEBS‐g‐MA and EPM‐g‐MA had more or less similar effects in dynamic mechanical properties of the blends. Additionally, melt rheological studies have also been pursued through a rubber process analyzer (RPA) to get a better insight.     

有机硅改性磺酸型聚氨酯/丙烯酸酯复合乳液的制备

将磺酸型聚酯多元醇、异佛尔酮二异氰酸酯（IPDI)和三羟甲基丙烷(TMP)在无有机溶剂参与的情况下进行预缩聚,以硅烷偶联剂γ-氨丙基三乙氧基硅烷（KH550）作为改性剂,加入双官能团单体甲基丙烯酸-β-羟乙酯(HEMA),得到含乙烯基和有机硅封端的聚氨酯作为种子乳液,然后与甲基丙烯酸甲酯(MMA)、丙烯酸丁酯(BA)混合单体共聚,合成了有机硅改性磺酸型聚氨酯/丙烯酸酯复合乳液。 红外光谱的表征确定了有机硅改性磺酸型聚氨酯/丙烯酸酯复合乳液的化学结构;透射电子显微镜观察证实了此复合乳液具有明显的核壳结构;热重分析表明,经有机硅和丙烯酸酯改性后,胶膜的最大热失重温度提高了20 ℃,X射线衍射分析表明胶膜的结晶度降低,有利于提高膜的韧性。 力学性能测试及吸水率测试结果表明,当有机硅含量为1.9%时,胶膜的拉伸强度最高达到25.03 MPa,断裂伸长率为328%,此时膜的吸水率最低。     

Dielectric relaxation of poly(ester-ether-carbonate) multiblock terpolymers

The dielectric properties of a series of poly(ester-ether-carbonate) multiblock terpolymers have been investigated as a function of ether and carbonate composition in the frequency range of 10³–10⁶ Hz. The degree of polymerization of the samples was determined by viscosimetry measurements. The weight fraction, degree of crystallinity, and melting temperatures were characterized by means of x-ray diffraction and DSC methods. Dielectric behavior has been discussed in terms of Havriliak-Negami formulation. The variation of the dielectric properties with temperature has been associated with two relaxation processes: a) the -relaxation process observed at low temperature, which is associated to local motion of polar groups attached to both the soft and the hard segments, and b) the process assigned to long-range molecular motions above the glass transition temperature.     

Strain induced strengthening of soft thermoplastic polyurethanes under cyclic deformation

We investigate the cyclic mechanical behavior in uniaxial tension of three different commercial thermoplastic polyurethane elastomers (TPU) often considered as a sustainable replacement for common filled elastomers. All TPU have similar hard segment contents and linear moduli but sensibly different large strain properties as shown by X-ray analysis. Despite these differences, we found a stiffening effect after conditioning in step cyclic loading which greatly differs from the common softening (also referred as Mullins effect) observed in chemically crosslinked filled rubbers. We propose that this self-reinforcement is related to the fragmentation of hard domains, naturally present in TPU, in smaller but more numerous sub-units that may act as new physical crosslinking points. The proposed stiffening mechanism is not dissimilar to the strain-induced crystallization observed in stretched natural rubber, but it presents a persistent nature. In particular, it may cause a local reinforcement where an inhomogeneous strain field is present, as is the case of a crack propagating in cyclic fatigue, providing a potential explanation for the well-known toughness and wear resistance of TPU.     

Thermal and photo-actuation in nematic elastomers

Mono domain nematic elastomers change shape by as much as 400% on being heated from the nematic to isotropic state. The reason is that nematic order, Q, elongates the distribution of chains and thus the network that they form. Experimental evidence for this, and simple theory is presented. A novel method to change Q, and hence obtain an analogous elastic strain, is to bend the nematic's rods by photoisomerization. On absorbing a photon, photochromes such as azo rods leave the (straight) trans state and adopt the cis (bent) form. We show data and give simple theory to explain this remarkable, reversible elastic phenomenon.     

Polyisobutylene-containing block polymers by sequential monomer addition. X. Synthesis of poly(α-methylstyrene-b-isobutylene-b-α-methylstyrene) thermoplastic elastomers

Preparatory to triblock synthesis experiments, the cationic polymerization of α-methylstyrene (αMeSt) was investigated using the 2-chloro-2,4,4-trimethylpentane (TMPCI)/TiCl₄ initiating system in the presence of triethylamine (Et₃N) as electron donor (ED) and CH₃Cl/n-hexane mixed solvent in the ?80 to ?40°C range. Conversions are influenced by temperature, [TiCl₄], [Et₃N], and [αMeSt]. The polymerization of αMeSt is living at ?80°C: Both termination and chain transfer to monomer are frozen out, however, initiation is slow relative to propagation. Highly syndiotactic (>94%) Pα Mest was obtained. At?60deg;C initiator efficiency is ca. 100%, but termination becomes evident. Et₃N may act both as Ed and as proton scavenger. Novel poly(α-methystyrene-b-isobutylene-b-α-methylstyrene) (PαMeSt-PIB-PαMeSt) triblocks have been synthesized by adding αMeSt to biliving polyisobutylene carbocations (⊕PIB⊕) in the ?80 to ?40°C range. The effects of temperature, solvent polarity, and [Et₃N] on the block copolymerization have been investigated. At ?80°C, the rate of crossover from ⊕PIB⊕ to αMeSt is lower than that of propagation of PαMeSt⊕, so that the triblock is contaminated by PIB and PIB-b-PαMeSt. At ?60°C, crossover occurs preferentially. The rate of propagation relative to that of crossover is also reduced by lowering the solvent polarity and increasing the [Et₃N]. High crossover efficiency and blocking efficiency can be obtained under optimum blocking conditions. The triblocks are novel thermoplastic elastomers (TPEs). © 1994 John Wiley & Sons, Inc.     

The effect of mesogenic and non-mesogenic crosslinking units on the phase behaviour of side-chain smectic and cholesteric elastomers

Chiral monomer (M₁ ), mesogenic and non-mesogenic crosslinking agents (C₁ and C₂ ), and the corresponding liquid crystalline elastomers (P₁ and P₂ series), have been synthesised. Their chemical structures have been characterised by Fourier transform infrared or ¹H nuclear magnetic resonance and their phase behaviour investigated by differential scanning calorimetry, polarising optical miscoscopy, thermo-gravimetric analysis (TGA) and X-ray diffraction. The effect of the crosslinking unit on the phase behaviour of the elastomers has been studied. M₁ showed a cholesteric oily streak and focal conic texture. C₂ exhibited a nematic enantiotropic thread-like and schlieren texture, and a monotropic fan-shaped texture in the S_A phase. Due to the introduction of the mesogenic crosslinking unit, elastomers, P_2-1 ?P_2-5 , exhibited a cholesteric phase, while elastomers, P_1-1 ?P_1-4 , derived from a non-mesogenic crosslinking unit, exhibit a S_A phase. As the content of the crosslinking unit increased, the T _g of the P₁ series initially decreased and then increased, and the T _i of the series decreased. In the P₂ series the T _g increased, but the T _i initially increased and then decreased. TGA confirmed that all the elastomers had improved thermal stability.     

氨基改性聚醚型聚硅氧烷的制备及其柔软性能研究

用含氢硅油、烯丙基缩水甘油醚、烯基聚醚的硅氢化加成产物-聚醚/环氧硅油与胺反应制得了氨基改性聚醚型聚硅氧烷（APEPS）,对其结构与性能进行了表征和研究。结果表明,含氢硅油分子量、有机胺结构、氨基改性聚醚型聚硅氧烷的硅含量对APEPS性能有影响。提高硅含量、增加氨值,可改善APEPS的柔软性与滑爽感,但对织物的吸湿性影响不大。     

A critical analysis of the effect of crosslinking on the linear viscoelastic behavior of styrene–butadiene rubber and other elastomers

The linear viscoelastic behavior in dynamic shear and tensile creep at temperatures from −30 to 70 °C is measured for an styrene–butadiene rubber (SBR) elastomer cured with dicumyl peroxide to crosslinking densities between 0 and 23.5 × 10⁻⁵ mol/cm³. The G′, G″, and tan δ isotherms are analyzed by time–temperature superposition (TTS), where the tan δ master curves are consistent with those of Mancke and Ferry. However, to achieve the TTS in the lightly crosslinked SBR systems, an anomalous vertical shift is required in the narrow temperature region from 10 to 30 °C. The vertical shift factor in this temperature region is not the standard from rubber elasticity. No anomalous behavior is detected in the equilibrium modulus, which is a linear function of temperature in accordance with the classical theory of rubber elasticity. In contrast to SBR, standard vertical shifts are required to effect TTS for uncrosslinked polybutadiene and an ethylene propylene diene monomer elastomer. © 2013 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Improving properties of natural rubber/polyamide 12 blends through grafting of diacetone acrylamide functional group

The aim of the present study was to improve the compatibility in blends of natural rubber (NR) and polyamide 12 (PA12) by grafting NR with hydrophilic monomer, diacetone acrylamide (DAAM), via seeded emulsion polymerization. The increase in polarity of NR after grafting modification was confirmed by a considerable increase in the polar component of its surface energy. Blends of graft copolymers of NR and poly(diacetone acrylamide) prepared using 10 wt% of DAAM (NR‐g‐PDAAM10) and PA12 were prepared at a 60/40 blend ratio (wt%) using simple blend and dynamic vulcanization techniques. The mechanical and rheological properties of the resulting blends were subsequently investigated and compared with those of the corresponding blends based on unmodified NR. The results show that dynamic vulcanization led to a significant increase in both mechanical and rheological properties of the blends. It was also observed that the dynamically cured NR‐g‐PDAAM10/PA12 blend had smaller particle size of vulcanized rubber dispersed in the PA12 matrix than observed for the dynamically cured NR/PA12 blend. This is due to the compatibilizing effect of DAAM groups present in NR‐g‐PDAAM10 molecule, which decreases the interfacial tension between the two polymeric phases. Therefore, it can be stated that the interfacial adhesion between NR and PA12 was improved by the presence of DAAM groups in NR molecule. This was reflected in the higher tensile properties observed in the dynamically cured NR‐g‐PDAAM10/PA12 blend. Copyright © 2017 John Wiley & Sons, Ltd.