The Potential of O‐MMT as a Reinforcing Filler for Uncured and Dynamically Cured PVC/XNBR Composites

Organic montmorillonite modified with quaternary ammonium (O‐MMT) was compounded with uncured and dynamically cured poly(vinyl chloride)/carboxylated nitrile butadiene rubber (PVC/XNBR) composites, using a Brabender Plasticorder at 130°C and 50 rpm rotor speed. The reinforcing efficiency of the O‐MMT was investigated in the uncured PVC/XNBR composite and the dynamically cured PVC/XNBR counterpart. Mixing and dynamic curing of the composites were monitored by typical torque‐time curves derived from a Brabender internal mixer. The torque‐time curves revealed that the dynamic curing process was successful and the incorporation of O‐MMT has no adverse effect on the processibility of the composites. It has been found that the introduction of crosslinks within the rubbery phase in the presence of the O‐MMT has further improved the tensile properties. DMA studies revealed that dynamically cured composite with O‐MMT showed higher storage modulus than the composite without O‐MMT. Furthermore, a one‐step tensile modulus vs. temperature curve and a related one peak tensile loss modulus vs. temperature curve were obtained, consequently, both are characteristics of a miscible polymers system. Further evidence on the composite miscibility was purchased by thermal scans from DSC, which showed a single glass transition temperature of PVC/XNBR composites. This claim was further supported by ATR‐IR spectra which revealed that hydrogen bonding is extensively involved in PVC/XNBR composites. This evidence unveiled the exact nature of the specific interactions responsible for miscibility and hence, enhanced mechanical properties. Furthermore, we proved in our studies the reinforcing role played by layered clay due to better dispersion, as well as improved interactions.     

Effect of a Nanoclay on the Mechanical,Thermal and Flame Retardant Properties of Rigid Polyurethane Foam

Water blown rigid polyurethane foams (PUF) with organoclay/organically modified nanoclay (ONC) were prepared and their properties such as density, mechanical, morphological, insulation, thermal and flame retardant properties were studied. In this investigation, the ONC content was varied from 1 to 10 parts per hundred of polyol (php) by weight. It was observed that the compressive strength of ONC filled PUF increased up to 3 php of ONC loading and then it decreased. Wide angle X-ray diffraction and transmission electron microscopy studies indicated the exfoliated dispersion of ONC in PUF. The thermal conductivity of ONC filled PUF decreases up to 5 php and then increases. The glass transition temperature (Tg) of PUF decreases on loading of ONC. The TGA analysis shows that there is slight increase in degradation temperature with increase in ONC loading. The flame retardant properties (LOI and flame spread rate) are improved slightly on addition (3 php) of ONC filled PUF.     

Quick estimation of the Dpb for predicting the strength of chemical bond in situ

An approximate method has been established to calculate the depth of the potential acting on an electron in a molecule at the saddle point along a chemical bond, denoted by Dpb. It is a new indicator which can be used for predicting the strength of a chemical bond. In this work, as a practical application for demonstrating thismethod, we calculated the Dpb of deoxyribonucleosides and ribonucleosides along all C-H and N-H chemical bonds using the method. The results are in fair agreement with those results of previously reported experimental and theoretical observations.     

SiO2/炭泡沫和SiC/炭泡沫复合材料的制备及表征

对炭泡沫为支撑骨架的氧化硅气凝胶(SiO₂/炭泡沫)和碳化硅(SiC/炭泡沫)复合材料分别采用XRD、SEM、激光导热仪、万能力学试验机进行物相、微观结构、热学及力学性能方面的表征.结果表明:所制备的SiO₂/炭泡沫与原炭泡沫相比,具备更高的抗压强度(14.95 MPa)和更低的室温热导率(0.44 W·m^-1·K^-1).SiC/炭泡沫材料则保持了较高的抗压强度值(14.66 MPa),其在 1 200 ℃下具备极低的高温热导率(2.18W·m^-1·K^-1).热重分析表明,SiC/炭泡沫在氧化氛围中到610 ℃才发生质量的损失,而内部炭发生完全烧蚀的温度高达844 ℃,这表明该材料的抗氧化性能远好于纯的炭泡沫材料.     

Oil Base Mud. Part I: Synthesis of Some Local Surfactants Used as Primary Emulsifiers for Oil Base Mud and Evaluation of Their Rheology Properties

Six oil soluble nonionic surfactants with different HLBs have been prepared. Their HLBs situate between 3.9 and 6.7. Transesterification was carried out for glycerol and triethanol amine with oleic acid at different moles to obtain six emusilifiers. They named glycerol momooleate (I), glycerol diooleate (II), glycerol trioleate (III), triethanol amine mono-, di- and tri-oleate (IV), (V,) and (VI). The chemical structure was confirmed using; the elemental analysis, FTIR and ¹HNMR. They were evaluated as a primary emulsifiers (PE) for thdrilling fluids (oil base mud) comparing with a currently used primary emulsifier (Fc). The water in oil base mud (w/o emulsions) was prepared. The concentration of emulsifiers and their HLB exhibited interesting rheology properties including shear-thinning behavior, yield value, viscoelastic effects, thixtropy, gel strength, and filtration loss. The rheology properties of such emulsions strongly depended on the average size distribution of the dispersed droplets that could be varied both with the bulk concentration and HLB value of the emulsifiers. The interfacial and surface properties of these emulsifiers suggest that the droplet size of the dispersed phase and bulk concentration are strongly related to the HLB value of emulsifiers. The w/o emulsion (mud formulation) stability is sensitive to the droplet size of the dispersed phase and HLB value of the used emulsifier. The results were discussed on the light the chemical structure of the primary emulsifiers and the emulsion ingredients.     

Evaporation/Precipitation from a W/O Microemulsion Base

The evaporation path in a microemulsion base of water, sodium dodecylsulfate, and pentanol was extended to include the subsequent precipitation stage caused by the restriction of the surfactant solubility. The results revealed the surfactant to be the only compound to precipitate during the evaporation/precipitation stage; the relative content of the two volatile compounds in the liquid phase was adjusted to the required level by the evaporation.     

Rheological Properties of Model and Crude Oil Systems when Wax Precipitate under Quiescent and Flowing Conditions

Wax precipitation and deposition is a recurring challenge in transportation of crude oil, and increased knowledge about the behavior of such systems is necessary. Microscopy and differential scanning calorimetry were used to follow the crystallisation of wax for two model systems. The amount of solid was also determined by the latter method as well. The flow and viscoelastic behavior were investigated around the wax precipitation temperature, and the yield stress was determined both after dynamic and static cooling. Interpretation of the results was carried out in view of crystal growth and microstructure of the wax crystals. The variables that were studied were wax composition, amount of wax and thermal and shear history.     

The liquid crystal properties of symmetric and non-symmetric dimers based on the azobenzene mesogenic group

A novel system of symmetric and non-symmetric dimers containing azobenzene groups has been synthesized and studied in an attempt to understand further the molecular origins of the intercalated smectic phases. For the non-symmetric dimers, the lack of symmetry was derived solely from the differences in length of the two terminal alkyl chains. Both the spacer and terminal chain lengths were varied. The spacer length was found to exert a profound influence on the clearing temperatures of these materials and a large odd-even effect was observed for the series. The smectic A phase stability was observed to increase with the terminal chain length, yet decrease with increasing spacer length. X-ray diffraction has revealed the structure of the smectic A phase of both the symmetric and non-symmetric azobenzene dimers to be of the monolayer type and not intercalated. The existence of the intercalated phase has previously been explained in terms of either a charge-transfer interaction, or by an electrostatic quadrupolar interaction. However, it has been thought that it may also be the result of an excluded volume or space filling constraint. For the non-symmetric liquid crystal dimers described here, a charge-transfer interaction should be minimal, as should the stabilization from the quadrupolar interaction between the two mesogens. However, it appears that some sort of specific interaction is required to stabilize the intercalated structure.     

基于主动式时间反转镜的声呐目标强度测量研究

为提高目标强度测量过程中的抗噪声、混响以及浅海多途干扰性能,从军标文件中的目标强度测量方法以及主动式时间反转镜的基本原理出发,经过研究和推演,发现可将基于单阵元的主动式时间反转镜与相关器结合应用于目标强度测量过程,提出了一种新的目标强度测量方法。该方法利用了主动式时间反转镜的抗多途特性,使得测量具有抗多途的性能;利用噪声与信号的不相关特性,算法结合相关器起到了很好的抗随机噪声效果;混响中的体积混响是随机的,算法具有抗体积混响的性能。论文分别从理论仿真和水池实验验证了算法的有效性和正确性。     

Developing Thermodynamic Micellization Approach to Model Asphaltene Precipitation Behavior

An little known yet significant issue in petroleum production processes in petroleum reservoirs is asphaltene precipitation/deposition. Asphaltene has not only a fuzzy and vague nature but it also can cause detrimental problems like reservoir blockage and, as a result, low oil recovery. To tackle this issue, many researchers have attempted to monitor asphaltene behavior versus thermodynamic conditions. A thermodynamic micellization approach is implemented in this work to describe asphaltene precipitation behavior for two sample fluids from Iranian reservoirs. First, the basic structures of the addressed approach and different contributions to Gibbs free energy of micellization proposed by Victorov and Firoozabadi (VF) are demonstrated. Second, a detailed sensitivity analysis with respect to the model parameters is performed by utilizing a new calculation strategy. Finally, a comparison between the predicted precipitation curve and the experimental one is illustrated; moreover, comparing our results with those reported by Victorov proves the superiority of the new strategy over the conventional one. The significance of this study shows the effect of each micellization parameter on the asphaltene precipitation behavior curve and illustrates the ability of the micellization approach evolved by VF in monitoring the effect of pressure on asphaltene precipitation using the new calculation procedure. Outcomes from this study could couple with commercial reservoir simulation software to improve precision and integrity for designing robust and effective production units.