堆积床内甲烷/空气预混燃烧的理论分析

在多孔介质内组织预混燃烧,燃气与多孔介质有强烈的换热作用,燃烧过程伴随着化学反应和热输运的强烈耦合。本文以惰性氧化铝球堆积床内的甲烷/空气预混燃烧为例,提出解析模型,对燃烧过程进行理论分析,给出温度分布的解析解,发现了超绝热火焰温度燃烧现象。     

Lattice Boltzmann方法模拟多孔介质Klinkenberg效应

格子Boltzmann数值模拟方法是研究复杂的多孔介质结构特别是Klinkenberg效应的有效方法之一，对处理复杂边值问题尤其有效，用格子Boltzmann方法研究了气流穿越多孔介质问题，并将数值计算结果与实验结果进行了比较，结果表明格子Boltzmann方法是数值模拟气流穿越多孔介质问题的有效方法之一。     

多孔介质中卡森流体的分形分析

研究了非牛顿流体中的卡森流体在多孔介质中的流动特性.基于服从分形分布的弯曲毛细管束模型,运用分形几何理论推导出了该流体在多孔介质中流动的流量、流速、启动压力梯度和有效渗透率的分形解析解.模型中的每一个参数都有明确的物理意义,它将卡森流体在多孔介质中的流动特性与多孔介质的微结构参数有机联系起来.文中给出了卡森流体的流速、启动压力梯度和有效渗透率随着各影响因素的变化趋势,并进行了讨论.所得分形模型可以更深刻地理解卡森流体在多孔介质中流动的内在物理机理. 关键词： 多孔介质 卡森流体 分形     

电化学沉积金属铜的分形枝晶生长控制与性能

 以CuSO_{4/sub>为前驱体,HCl为添加剂,采用电化学沉积方法,在室温条件下制得了μm级、面心立方结构分形铜的枝状晶体,研究了铜离子浓度、硫酸浓度、电流密度、沉积时间、氯离子浓度等实验参数对分形枝状铜晶体尺寸、结构的影响。结果表明：硫酸的浓度对铜沉积物结构无明显影响;随着Cu^{2+/sup>浓度的不断增大,铜沉积物的分形效果越来越明显;增大电流密度（0.4～1.6 A·cm-2/sup>）,铜沉积物由致密向多分枝的开放型转变;延长沉积时间（大于等于5 min）,可获得含大量次级分枝铜的晶体;适当增加盐酸用量（0.05～0.20 mol/L）,铜沉积物枝晶尺寸显著减小。最后讨论了分形枝晶铜在碱性条件下氧化甲醇的电化学性能。}}     

Microstructure change in deuterium implanted CLAM steel induced by electron irradiation

As Reduced Activation Ferritic/Martensitic (RAFM) steel is considered the primary candidate for use as a structural material in fusion power reactors,many countries are developing different kinds of RAFM.China is developing new CLAM (China Low Activation Martensitic) steel.The study investigates microstructural changes in CLAM steel implanted with deuterium ions induced by 1250 keV electron irradiation from R.T.to 873 K,and observes both the growth and shrinkage of the defect clusters produced by deuterium ...     

Carbide precipitates in solution-quenched PH13-8 Mo stainless steel: A small-angle neutron scattering investigation

This paper deals with the small-angle neutron scattering (SANS) investigation on solution-quenched PH13-8 Mo stainless steel. From the nature of the variation of the functionality of the profiles for varying specimen thickness and also from the transmission electron microscopy (TEM), it has been established that the small-angle scattering signal predominantly originates from the block-like metallic carbide precipitates in the specimen. The contribution due to double Bragg reflection is not significant in the present case. The single scattering profile has been extracted from the experimental profiles corresponding to different values of specimen thickness. In order to avoid complexity and non-uniqueness of the multi-parameter minimization for randomly oriented polydisperse block-like precipitate model, the data have been analyzed assuming randomly oriented polydisperse cylindrical particle model with a locked aspect ratio.     

规则结构多孔填料塔两相流动特性实验研究

本文以空气和水为工质,对规则结构多孔填料塔的气-液逆向流动特性进行了可视化实验,研究了填料塔内气一液两相流动规律.实验结果表明:当液体流量一定时,随着气体流量的增加,压力损失增大;当气体流量一定时,随着液体流量的增加,气相压力损失增加.根据实验结果提出了采用水力雷诺数、韦伯数和无量纲流动参数的填料塔内气-液两相流动阻力系数实验关联式.     

Explicit analytical solutions of the anisotropic Brinkman model for the natural convection in porous media (Ⅱ)

Some algebraically explicit analytical solutions are derived for the anisotropic Brinkman model―an improved Darcy model―describing the natural convection in porous media. Besides their important theoretical meaning (for example, in analyzing the non-Darcy and anisotropic effects on the convection), such analytical solutions can be the benchmark solutions that can promote the development of computational heat and mass transfer. Some solutions considering the anisotropic effect of permeability have been given previously by the authors, and this paper gives solutions including the anisotropic effect of thermal conductivity and the effect of heat sources.     

Pulsed Nd:YAG laser welding of AISI 304 to AISI 420 stainless steels

The technique to weld AISI 304 stainless steel to AISI 420 stainless steel with a pulsed Nd:YAG laser has been investigated. The main objective of this study was to determine the influence of the laser beam position, with respect to the joint, on weld characteristics. Specimens were welded with the laser beam incident on the joint and moved 0.1 and 0.2 mm on either side of the joint. The joints were examined in an optical microscope for cracks, pores and to determine the weld geometry. The microstructure of the weld and the heat affected zones were observed in a scanning electron microscope. An energy dispersive spectrometer, coupled to the scanning electron microscope, was used to determine variations in (weight %) the main chemical elements across the fillet weld. Vickers microhardness testing and tensile testing were carried out to determine the mechanical properties of the weld. The results of the various tests and examinations enabled definition of the best position for the incident laser beam with respect to the joint, for welding together the two stainless steels.     

有序排列PMMA 模板法合成三维有序纳米孔道MgO

"利用由无乳化剂的乳液聚合法和水浮法联用技术合成得到的有序排列的聚甲基丙烯酸甲酯(PMMA)微球为硬模板,以硝酸镁为镁源,并采用硝酸镁-柠檬酸-乙醇混合溶液浸渍PMMA微球后经干燥以及先后在300 ℃恒温灼烧3 h和500 ℃恒温灼烧5 h,制备出具有有序纳米孔道结构的MgO粒子．应用X射线衍射、高分辨扫描电子显微镜、透射电子显微镜/选区电子衍射以及N2吸附-脱附法等技术表征了PMMA和MgO样品的物理化学性质．结果表明,所得PMMA微球颗粒较为均匀,粒径约为284 nm,且排列规整有序．由PMMA硬模板