Passive control of the flow around a square cylinder using porous media

The passive control of bluff body flows using porous media is investigated by means of the penalization method. This method is used to create intermediate porous media between solid obstacles and the fluid in order to modify the boundary layer behaviour. The study covers a wide range of two‐dimensional flows from low transitional flow to fully established turbulence by direct numerical simulation of incompressible Navier–Stokes equations. A parametric study is performed to illustrate the effect of the porous layer permeability and thickness on the passive control. The numerical results reveal the ability of porous media to both regularize the flow and to reduce the drag forces up to 30%. Copyright © 2004 John Wiley & Sons, Ltd.     

Sulfur Concentration in Nanoporous Alumina Membrane

Nanoporous alumina membrane prepared by anodic oxidation using sulfuric acid electrolyte was subjected to TG-DTA and X-ray Photoelectron Spectroscopy (XPS or ESCA) to further study the distribution of sulfur. In XPS study, Ar⁺ ion bombardment was performed on the sample to etch the surface at a rate of 3 nm min^-1. As a result, sulfur was found to be concentrated within a depth of 3nm from the surface. The S content of the surface was found to be 2.7±0.5 wt%, and that at a depth of ca. 3 nm and ca. 10 nm was found to be as low as about 0.6±0.11 wt% (5.37±1.0 wt%→ 1.26±0.2wt% SO₂). In TG-DTA, the mass loss of 7.3% was in fair agreement with that calculated on XPS results (7.1±1.2%). This revised version was published online in July 2006 with corrections to the Cover Date.     

The modified characteristic finite difference fractional steps method for the coupled system of fluid dynamics in porous media and its analysis

For the coupled system of multilayer fluid dynamics in porous media, the modified characteristic finite difference fractional steps method applicable to parallel arithmetic is put forward and two‐dimensional and three‐dimensional schemes are used to form a complete set. Some techniques, such as calculus of variations, energy method, piecewise biquadratic interpolation, multiplicative commutation rule of difference operators, decomposition of high order difference operators and prior estimates are adopted. Optimal order estimates in L² norm are derived to determine the error in the approximate solution. This method has already been applied to the numerical simulation of multilayer fluid dynamics in porous media. © 2003 Wiley Periodicals, Inc. Numer Methods Partial Differential Eq 19: 665–681, 2003.     

FREE BOUNDARY PROBLEM ARISING FROM EVAPORATION FROM POROUS MEDIUM

ＦＲＥＥＢＯＵＮＤＡＲＹＰＲＯＢＬＥＭＡＲＩＳＩＮＧＦＲＯＭＥＶＡＰＯＲＡＴＩＯＮＦＲＯＭＰＯＲＯＵＳＭＥＤＩＵＭＹＡＮＧＬＩＰＩＮＧ（杨力平）（ＤｅｐａｒｔｍｅｎｔｏｆＡｐｐｌｉｅｄＭａｔｈｅｍａｔｉｃｓ，ＴｓｉｎｇｈｕａＵｎｉｖｅｒｓｉｔｙ，Ｂｅ...     

Determination of the rate of rapid lipid transfer induced by poly(ethylene glycol) using the SLM Fourier transform phase and modulation spectrofluorometer

Rate constants were determined for the transfer of the fluorescent lipid probe 1-palmitoyl-2-[[2-[4-(6-phenyl-trans-1,3,5-hexatrienyl)phenyl]ethyl] oxy]carbonyl]-3-sn-phosphatidylcholine (DPHpPC) between large, unilamellar extrusion vesicles composed either of dipalmitoyl phosphatidylcholine (DPPC) or of DPPC mixed with a small amount (0.5 mol%) of lyso phosphatidylcholine (Lyso PC). Transfer of the lipid probe in the presence of varying concentrations of poly(ethylene glycol) (PEG) was monitored using the SLM 48000-MHF Multi-Harmonic Fourier Transform phase and modulation spectrofluorometer to collect multifrequency phase and modulation fluorescence data sets on a subsecond time scale. The unique ability of this instrument to yield accurate fluorescence lifetime data on this time scale allowed transfer to be detected in terms of a time-dependent change in the fluorescent lifetime distribution associated with the lipid-like DPHpPC probe. This probe demonstrates two short fluoresence decay times (ca. 1.1–1.4 and 4.3–4.8 ns) in a probe-rich environment but a single long lifetime (ca. 7 ns) in a probe-poor environment. A simple two-state model for initial lipid transfer was used to analyze the multifrequency data sets collected over a 4-s time frame to obtain the time rate of change of the concentrations of donor and acceptor probe populations following rapid mixing of vesicles with PEG. The ability to measure fluorescence lifetimes on this time scale has allowed us to show that the of rate of lipid transfer increased dramatically at 35% PEG in both fusing and nonfusing vesicle systems. These results are interpreted in terms of a distinct interbilayer structure associated with intimate bilayer contact induced by high and potentially fusogenic concentrations of PEG.     

Investigation of sulfonated poly(ether ether ketone sulfone)/heteropolyacid composite membranes for high temperature fuel cell applications

The sulfonated poly(ether ether ketone sulfone) (SPEEKS)/heteropolyacid (HPA) composite membranes with different HPA content in SPEEKS copolymers matrix with different degree of sulfonation (DS) were investigated for high temperature proton exchange membrane fuel cells. Composite membranes were characterized by Fourier transfer infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). FTIR band shifts suggested that the sulfonic acid groups on the copolymer backbone strongly interact with HPA particles. SEM pictures showed that the HPA particles were uniformly distributed throughout the SPEEKS membranes matrix and particle sizes decreased with the increment of copolymers' DS. The holes were not found in SPEEKS‐4/HPA30 (consisting of 70% SPEEKS copolymers with DS = 0.8 and 30% HPA) composite membrane after composite membranes were treated with boiling water for 24 h. Thermal stabilities of the composite membranes were better than those of pure sulfonated copolymers membranes. Although the composite membranes possessed lower water uptake, it exhibited higher proton conductivity for SPEEKS‐4/HPA30 especially at high temperature (above 100 °C). Its proton conductivity linearly increased from 0.068 S/cm at 25 °C to 0.095 S/cm at 120 °C, which was higher than 0.06 S/cm of Nafion 117. In contrast, proton conductivity of pure SPEEKS‐4 membrane only increased from 0.062 S/cm at 25 °C to 0.078 S/cm at 80 °C. At 120 °C, proton conductivity decreased to poor 0.073 S/cm. The result indicated that composite membranes exhibited high proton conductivity at high temperature. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1967–1978, 2006     

Polymer electrolyte membranes for the direct methanol fuel cell: A review

The direct methanol fuel cell (DMFC) has the potential to replace lithium‐ion rechargeable batteries in portable electronic devices, but currently experiences significant power density and efficiency losses due to high methanol crossover through polymer electrolyte membranes (PEMs). Numerous publications document the synthesis and characterization of new PEMs for the DMFC. This article reviews this research, transport phenomena in PEMs, and experimental techniques used to evaluate new PEMs for the DMFC. Although many PEMs do not show significant improvements over Nafion®, the benchmark PEM in DMFCs, experimental results show that several new PEMs exhibit lower methanol crossover at similar proton conductivities and/or higher DMFC power densities. These results and recommendations for future research are discussed. © 2006 Wiley Periodicals, Inc. J Polym Sci Parts B: Polym Phys 44: 2201–2225, 2006     

Mechanical endurance of polymer electrolyte membrane and PEM fuel cell durability

The life of proton exchange membrane fuel cells (PEMFC) is currently limited by the mechanical endurance of polymer electrolyte membranes and membrane electrode assemblies (MEAs). In this paper, the authors report recent experimental and modeling work toward understanding the mechanisms of delayed mechanical failures of polymer electrolyte membranes and MEAs under relevant PEMFC operating conditions. Mechanical breach of membranes/MEAs in the form of pinholes and tears has been frequently observed after long‐term or accelerated testing of PEMFC cells/stacks. Catastrophic failure of cell/stack due to rapid gas crossover shortly follows the mechanical breach. Ex situ mechanical characterizations were performed on MEAs after being subjected to the accelerated chemical aging and relative humidity (RH) cycling tests. The results showed significant reduction of MEA ductility manifested as drastically reduced strain‐to‐failure of the chemically aged and RH‐cycled MEAs. Postmortem analysis revealed the formation and growth of mechanical defects such as cracks and crazing in the membranes and MEAs. A finite element model was used to estimate stress/strain states of an edge‐constrained MEA under rapid RH variations. Damage metrics for accelerated testing and life prediction of PEMFCs are discussed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2346–2357, 2006     

Sulfonated poly(aryl ether ether ketone ketone)s containing fluorinated moieties as proton exchange membrane materials

A series of sulfonated poly(aryl ether ether ketone ketone)s statistical copolymers with high molecular weights were synthesized via an aromatic nucleophilic substitution polymerization. The sulfonation content (SC), defined as the number of sulfonic acid groups contained in an average repeat unit, could be controlled by the feed ratios of monomers. Flexible and strong membranes in sodium sulfonate form could be prepared by the solution casting method, and readily transformed to their proton forms by treating them in 2 N sulfuric acid. The polymers showed high T_gs, which increased with an increase in SC. Membranes prepared from the present sulfonated poly(ether ether ketone ketone) copolymers containing the hexafluoroisopropylidene moiety (SPEEKK‐6F) and copolymers containing the pendant 3,5‐ditrifluoromethylphenyl moiety (SPEEKK‐6FP) had lower water uptakes and lower swelling ratios in comparison with previously prepared copolymers containing 6F units. All of the polymers possessed proton conductivities higher than 1 × 10^?2 S/cm at room temperature, and proton conductivity values of several polymers were comparable to that of Nafion at high relative humidity. Their thermal stability, oxidative stability, and mechanical properties were also evaluated. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2299–2310, 2006