Rate processes on fractals: Theory,simulations, and experiments

Heterogeneous kinetics are shown to differ drastically from homogeneous kinetics. For the elementary reaction A + A products we show that the diffusion-limited reaction rate is proportional tot ^– h[A]² or to [A]^x, whereh=1- d _s/2, X=1+2/d _s =(h-2)(h-1), andd _s is the effective spectral dimension. We note that ford = d _s =1, h =1/2 andX = 3, for percolating clustersd _s = 4/3,h = 1/3 andX = 5/2, while for dust ds <1, 1 >h > 1/2 and >X > 3. Scaling arguments, supercomputer simulations and experiments give a consistent picture. The interplay of energetic and geometric heterogeneity results in fractal-like kinetics and is relevant to excitation fusion experiments in porous membranes, films, and polymeric glasses. However, in isotopic mixed crystals, the geometric fractal nature (percolation clusters) dominates.     

可降解自固化类骨磷灰石支架的研究

0引言一直以来,钙磷生物材料如羟基磷灰石(hy-droxyapatite,HA)由于其成份与骨的无机成份相似,具有良好的生物相容性,作为骨修复材料引起了人们广泛的兴趣。磷酸钙骨水泥是一类可在生理条件下自固化的非陶瓷型类HA人工骨材料,这种由磷酸钙骨水泥(calcium phosphate cement,CPC)转变而成的HA,与天然骨磷灰石有类似的组成结构,植入人体后可参与新陈代谢,促进骨组织生长[1,2]。一些研究显示,CPC具有成骨活性和生物降解性,在体内被吸收的同时可引导新骨的生成,从而可克服自体骨、磷酸三钙陶瓷因吸收降解过快造成的局部缺陷以及陶瓷型HA长…     

互通多孔碳/二氧化锰纳米复合材料的原位水热合成及电化学性能

以互通多孔碳（IPC）为载体，水热条件下在碳表面原位反应生成纳米结构的二氧化锰（MnO₂），制备互通多孔碳/二氧化锰纳米（IPC/MnO₂）复合电极材料. 采用扫描电镜（SEM），透射电镜（TEM），X射线衍射（XRD），热重分析（TGA）对其结构进行表征；采用循环伏安法、恒流充放电和交流阻抗对其电化学性能进行研究. 结果表明：生成的MnO₂均匀地负载在碳的表面，形成多层次结构，并且随着温度的升高IPC表面负载的MnO₂由纳米颗粒变为纳米片状结构；MnO₂纳米片具有典型的K-Birnessite 型晶体结构；复合物中MnO₂的含量约为34%（w）. 在100 ℃制备的IPC/MnO₂复合材料在三电极系统中最高比电容达到了411 F·g^-1；随着反应温度的升高,比容量先增长后基本保持不变. 以IPC/MnO₂为正极，活性炭（AC）为负极，1 mol·L^-1 Na₂SO₄溶液为电解液组装成IPC/MnO₂//AC 混合超级电容器，发现IPC/MnO₂电极的电容器其电位窗口从1 V扩展到1.8 V，容量可达86F·g^-1，且表现出良好的电容特性和大电流放电性能.     

Modification of Non-Hydrolytic Sol-Gel Derived Alumina by Solvent Treatments

The effect of wetting non-hydrolytic derived alumina xerogels with water and organic solvents in the 20–70°C range on the alumina's properties was investigated. Wetting with organic solvents does not affect the alumina. However, contact with water was found to change the sharp crystallization at 800°C to a continuous crystallization starting at 450°C. Water treatment for a day at room temperature (RT) followed by second calcination decreased the surface area by 10%. This decrease in surface area is less pronounced with increasing wetting periods. On the other hand water treatment at 50–70°C followed by a second calcination resulted in a surface area increase of up to 15%. Upon water treatment the total pore volume has decreased from 0.65 (cm³/gr) to 0.48 (cm³/gr) and the average pore size decreased from 6.8 nm to 4.1 nm. The Cl content was found to be uneffected by the water treatment, remaining at 2.5% wt. Wetting with water at elevated temperature (70°C) accelerated the morphological changes, eliminating the crystallization peak at 800°C in one hour. A dissolution-reprecipitation mechanism is suggested to explain the results. In addition, Mass-Spectroscopy of the effluent gas during heat treatment revealed the emission of CO₂ and water upon phase transition into -Al₂O₃, at 1150–1300°C.     

Influence of velocity and surface temperature of alumina particles on the properties of plasma sprayed coatings

In this paper are described the main characteristics of the plasma spraying process of alumina deposits, i.e., the temperature and flow field of the plasma jets obtained with the classical spraying torches, the injection of the particles into the plasma jet, the particle surface temperature and velocities in the plasma (measured for calibrated alumina particles), and the coating generation. The measurements on the alumina particles are compared with the predictions of a mathematical model. The experimental and computed particle velocities are in rather good agreement. However, this is not the case for the particle surface temperature. Possible reasons for the discrepancy are proposed (influence of the carrier gas, thermophoretic forces, and poor penetration of the particles into the plasma core even for an injection velocity twice that of the optimal calculated one, as shown by recent measurements). Finally the correlations between the particle velocities and surface temperature, and the properties of the alumina coating (porosity, crystal structure, mechanical properties) are studied.     

Steam-carbon gasification catalyzed by calcium: Assessment of the porous structure of active carbons from plum stones and synthetic active carbons

A need for an elaboration of the methods for synthesis and characterization of activated carbons with a requisite porous structure has existed for a long time. One of the methods giving possibility for creating controlled mesopore and micropore structures deals with the steam gasification of various carbon materials. In this work the effects of calcium catalyst on the catalytic steam gasification of active carbons from plum stones and porous polymers are presented. Determination of micropores capacity and specific adsorption in mesopores have been performed by means of the _s method, but adsorption on the heterogeneous solids was described by the integral equation with various local isotherms. This equation has been solved by the regularization method. Based on this method the changes in structural parameters of active carbons depending on the amount of calcium catalyst were estimated.Nomenclature d width of slit-like micropore - F(x) distribution function of the half-width - p vapor pressure of sorbate - p/p _N relative pressure - PSAC Plum Stone Active Carbon - average pore radius, nm - S ₁ relative limit of the validity of experimental point on the adsorption isotherm in the computations by means of regularization method - SAC Synthetic Active Carbon - S _BET specific surface area calculated by means of BET method, m²/g - S _mes mesopore surface area, m²/g - S _mic micropore surface area, m²/g - T absolute temperature, K - V _mes sorption capacity of mesopores, cm³/g - V _mic sorption capacity of micropores, cm³/g - V _p sorption capacity of pores, cm³/g - w/w weight in weight concentration - x half-width of slit-like micropore, nm - x ₁ maximum of half-width of micropore slit, nm - average half-width of slit-like micropore, nm - X _min-X _max integration limits of thex Greek Letters Greek Letters variance of average half-width of slit-like micropore, nm² - local relative filling of micropores - total relative filling of micropores     

Preparation and Characterization of Nano-ZnFe2O4/TiO2 Films

The nano-ZnFe2O4/TiO2 films possess the functions of desulfurization and degradation for organic pollutants. The sols of ZnFe2O4/TiO2 were prepared by sol-gel method and coated on glass and porous ceramic by vertical coating and dipping-lift processes, respectively, and the samples were obtained after drying and sintering. The composition, appearance, absorption spectrum of the films, and the influence of the film on porous ceramic performances were analyzed using SEM, AFM, UV-Vis spectrometer, and mercury porosimeter, respectively, to determine the operation parameters of the multifunction porous ceramic elements for gas-purification.     

有序自组装聚合物纳米结构

采用水辅助方法(water-assisted fabrication method),分别以4-十二烷基苯磺酸掺杂的聚苯胺(PANI-DBSA)和聚2-甲氧基-5-(2′-乙烯基-己氧基)苯乙炔(MEH-PPV)两种功能高聚物为成膜材料,冷凝水滴为模板,利用水滴在聚合物溶液表面的自组装,制备出了两种纳米层次以上的蜂窝状有序多孔聚合物薄膜.通过原子力显微镜和共聚焦荧光显微镜对其形貌、电学性质和荧光图像进行了表征.     

The evolution of morphology of ordered porous TiO2 films fabricated from sol-gel method assisted ZnO nanorod template

Ordered porous TiO₂ films, including TiO₂ nanotube arrays, are fabricated by a sol-gel dip-coating approach via ZnO nanorod templates obtained from aqueous solution approach. The results indicate that the morphologies of ordered porous TiO₂ films have been great affected by the sol-gel dip-coating cycle number. Open-ended TiO₂ nanotube arrays can be obtained in optimum dip-coating cycle numbers. The TiO₂ nanotubes with the inner diameter matching well with the diameters of ZnO nanorods, are well assembled and separate each other. When the cycle number is less than this optimum value, no intact porous TiO₂ film can be obtained. As the cycle number is larger than this optimum value, an ordered porous TiO₂ film with many throughout holes is formed. The evolutive mechanism of ordered porous TiO₂ films is proposed.     

氧化锰团簇粒子在有序多孔氧化锆孔道中的组装及其特殊性能研究

利用醇溶液浸渍法及后续的热处理工艺成功实现了氧化锰团簇粒子在有序多孔氧化锆孔道中的组装，借助XRD，TEM，UV-vis，EPR以及O~2-TPD等分析手段进行样品结构表征及性能分析。研究表明，氧化锰团簇粒子能比较均匀地分散于规则的孔道中；团簇粒子的生长随着热处理温度的提高受到孔道大小的限制；孔道中的氧化锰团簇粒子能显示出与较大尺寸氧化锰粒子完全不同的强顺磁信号，并且还具有优异的表面氧吸附特性。