基于串联两阶段网络DEA模型的供应链规模收益分析

数据包络分析(DEA)是评价供应链系统(Supply chain system)间相对有效性的一种重要的工具,但是传统的DEA不考虑供应链的内部结构,对系统效率评价偏高;而本文所研究两阶段串联供应链系统,考虑把部分中间产品作为最终产品输出,增加额外中间投入的情形.基于所提出的供应链系统结构,本文建立相应的串联结构下的网络DEA模型,并针对所建立模型进行相关理论的研究,给出了串联结构下的生产可能集和规模收益情况判定方法.最后,进行数值实验,以验证我们提出的结论.     

Formation of porous polymer morphology by microsyneresis during divinylbenzene polymerization

This article describes the investigation of the importance of various reaction conditions on microsyneretic pore formation during polymerization of divinylbenzene (DVB) under so‐called “solvothermal” conditions. To induce microsyneretic pore formation, the most important parameter is an unusually high dilution of monomers with a “good” porogen solvating the polymer chains. High dilution and solvation of the growing poly(DVB) chains promote the prolongation of the polymer chains rather than their interconnection by crosslinking. Consequently, when the polymer gel density reaches the point where syneresis starts, the polymer network is geometrically too extensive to be broken up into precipitating entities and, instead, porogen droplets are formed within the continuous polymer gel. The pore geometry created by microsyneresis offers high surface area in wide mesopores and hence, high capacity for supporting functional groups or reactions with much better accessibility than narrow pores between polymer microspheres produced by macrosyneresis in conventional styrenic polymer supports. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 774–781     

Path to achieving molecular dispersion in a dense reactive mixture

A uniform dispersion of reactants is necessary to achieve a complete reaction involving multicomponents. In this study, we have examined the role of plasticizer in the reaction of two seemingly unlikely reactants: a highly crystalline hexamethylenetetramine (HMTA) and a strongly hydrogen bonded phenol formaldehyde resin. By combining information from NMR, infrared spectroscopy and differential scanning calorimetry, we were able to determine the role of specific intermolecular interactions necessary for the plasticizer to dissolve the highly crystalline HMTA and to plasticize the phenol formaldehyde resin in this crosslinking reaction. The presence of the plasticizer increased the segmental mobility, disrupted the hydrogen bonded matrix, and freed the hydroxyl units, which further increased the solubility of the HMTA. Both the endothermic and exothermic transitions are accounted for in the calorimetric data obtained. For the first time, it is possible to obtain the effective molar ratio of each component needed to complete the crosslinking reaction efficiently. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1519–1526     

基于深度学习的ELM实时识别研究

基于深度学习的方法，在HL-2A装置上开发出了一套边缘局域模(ELM)实时识别算法。算法使用5200次放电数据(约24.19万数据切片)进行学习，得到一个深度为22层的卷积神经网络。为衡量算法的识别能力，识别了HL-2A装置自2009年实现稳定ELMy H模放电以来所有历史数据(约26000次放电数据)，共识别出1665次H模放电，其中误识别35次，误报率为2.10%。在实际的1634次H模放电中，漏识别4次，漏识别率为0.24%。该误报率和漏报率可以满足ELM实时识别的精度要求。识别算法在实时控制环境下，对单个时间点的平均计算时间为0.46ms，可以满足实时控制的计算速度要求。     

Synthesis and Self-Assembly of Mixed-Graft Block Copolymers

Mixed-graft block copolymers (mGBCPs) consist of two or more types of polymeric side chains grafted on a linear backbone in a random, alternating, or pseudo-alternating sequence. They can phase-separate with the backbone serving as the interface of the blocks, and the side chains dominate their self-assembly behavior. mGBCPs are an accessible polymer architecture for exploring the idea of encoding polymer properties through the macromolecular architecture, as there are two distinct structural components that can be tuned: the backbone and the side chains. In this Concept article, the current literature on the synthesis of mGBCPs is reviewed, and the advantages and disadvantages of each synthetic method are noted. The self-assembly of mGBCPs is also discussed where possible. Finally, directions for future research on mGBCP synthesis and self-assembly are suggested.     

Crosslinking network of bio‐based bis‐functional epoxides derived from trans‐limonene oxide

The thiol‐ene reaction between trans‐limonene oxide (trans‐LO) and ethane‐1,2‐dithiol in the presence of triethylborane affords a bio‐based bis‐functional epoxide (bis‐trans‐LO). The crosslinking reaction of bis‐trans‐LO with branched polyethyleneimine (BPEI; M_n = 600; BPEI₆₀₀) at a feed ratio of bis‐trans‐LO/BPEI₆₀₀ = 57/43 (wt/wt) yields the corresponding network polymer with T_d10 (10% thermal decomposition temperature) of 304.7 °C in 98% yield. In contrast, negligible amounts of network polymer are obtained by the reaction of bis‐LO (bis‐functional epoxide derived from cis and trans‐LO) and BPEI₆₀₀ regardless of the feed ratio. The mechanical strengths as measured by direct tensile tests of the network polymers derived from bis‐trans‐LO and BPEI_600,1800 (M_n = 600 and 1800) were approximately 16 and 11 times higher than that of bis‐LO and BPEI₁₈₀₀, respectively. The tensile shear strengths of the metal‐to‐metal adhesive bonds induced by bis‐trans‐LO and BPEI_600,1800 were 9.5 and 14.1 MPa, respectively. DMA revealed that the storage modulus of the network polymer derived from bis‐trans‐LO and BPEI₁₈₀₀ in the rubber region was higher than that of the material prepared from bis‐LO and BPEI₁₈₀₀, indicating higher crosslink density of the bis‐trans‐LO/BPEI₁₈₀₀ system. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2466–2473     

Donor-acceptor copolymers from cyclopentannulation polymerizations with dicyclopenta[cd,jk]pyrene and dicyclopenta[cd,lm] perylene acceptors

A series of donor-acceptor copolymers with dicyclopenta[cd,jk]pyrene and dicyclopenta[cd,lm]perylene acceptor units was prepared via palladium catalyzed cyclopenta-annulation reactions. The acceptor units were paired with diethynyl containing donor groups based on benzo[1,2-b:4,5-b’]dithiophene, thieno[3,2-b]thiophene, and 4-octyl-4H-dithieno[3,2-b:2′,3′-d]pyrrole to create six polymer variants. The cyclopentannulation polymerization resulted in copolymers with molecular weights (Mn) of 6–14 kDa and broad light absorption in the visible region with band gaps of 1.38–1.85 eV. The synthetic methodology, as well as optoelectronic properties, including thin-film absorption and cyclic voltammetry, of the donor-acceptor copolymers are presented.     

Hydrothermal Synthesis and Structure of a Novel Coordination Polymer Co_3(tma)(pda)_2(H_2O)_3]n·nH_2O

1INTRODUCTION Recently,the design and preparation of coordina-tion polymers with new porous frameworks are of great interest due to their potential functionalities such as catalysis,gas absorption,separation and molecu-lar recognition.In designing1-D,2-D and3-D porous coordination polymers,the selection of appropriate ligands is crucial for determining the structure.The mixed-linker systems of both carboxylates and pyri-dyls have proved to be effective for the preparation of novel coordi…     

A profit-maximizing supply chain network design model with demand choice flexibility

We present a profit-maximizing supply chain design model in which a company has flexibility in determining which customers to serve. The company may lose a customer to competition if the price it charges is too high. We show the problem formulation and solution algorithm, and discuss computational results.     

Multicriteria decision making under uncertainty

Formalization for problems of multicriteria decision making under uncertainty is constructed in terms of guaranteed and weak estimates. A relevant definition of the vector maximinimax value is given. Parameterization and approximation of maximum, minimax, and maximinimax values based on the inverse logical convolution are suggested. An application for multicommodity networks is considered. Received: December 13, 2000 / Accepted: August 21, 2001?Published online May 8, 2002