Synthesis and properties of novel polyimide/nylon‐6 triblock copolymers

Nylon‐6‐b‐polyimide‐b‐nylon‐6 copolymers were prepared by first synthesizing a series of imide oligomers end‐capped with phenyl 4‐aminobenzoate. The oligomers were then used to activate the anionic polymerization of molten ϵ‐caprolactam. In the block copolymer syntheses, the phenyl ester groups reacted quickly with caprolactam anions at 120 °C to generate N‐acyllactam moieties, which activated the anionic polymerization. In essence, nylon‐6 chains grew from the oligomer chain ends. All of the block copolymers had higher moduli and tensile strengths than those of nylon‐6. However, their elongations at break were much lower. The thermal stability, chemical resistance, moisture resistance, and impact strength were dramatically increased by the incorporation of only 5 wt % polyimide in the block copolymers. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4247–4257, 2000     

Poly(arylene ether)s,poly(arylene thioether)s,and poly(arylene sulfone)s derived from a dihydroxy(imidoarylene) monomer

Novel poly(arylene ether)s, poly(arylene thioether)s, and poly(arylene sulfone)s were synthesized from the dihydroxy(imidoarylene) monomer 1 . The syntheses of poly(arylene ether)s were carried out in DMAc in the presence of anhydrous K₂CO₃ by a nucleophilic substitution reaction between the bisphenol and activated difluoro compounds. Poly(arylene thioether)s were synthesized according to the recently discovered one-pot polymerization reaction between a bis(N,N′-dimethyl-S-carbamate) and activated difluoro compounds in the presence of a mixture of Cs₂CO₃ and CaCO₃. The bis(N,N′-dimethyl-S-carbamate) 3 was synthesized by the thermal rearrangement reaction of bis(N,N′-dimethylthiocarbamate) 2 , which was synthesized from 1 by a phase-transfer catalyzed reaction. The poly(arylene thioether)s were further oxidized to form poly(arylene sulfone)s, which would be very difficult, if not impossible, to synthesize by other methods. All of the polymers described have extremely high T_gs and thermal stability as determined from DSC and TGA analysis. Poly(arylene sulfone)s have the highest T_gs and they are in the range of 298–361°C. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1201–1208, 1998     

Preparation and properties of processable polyimides having bulky pendent ether groups

A series of aromatic diamines containing pendent methoxy, phenoxy, and biphenoxy moieties were synthesized. By the reaction of diamines with 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA), several kinds of polyimides having bulky pendent ether groups were synthesized. Thermal properties and processability such as melt processability and solubility in organic solvents of obtained polyimides were investigated by focusing on the chemical structures of their repeating structure units. It was found that the thermal stability and melt processability of the polyimides did not strongly depend on the existence of bulky pendent phenoxy and biphenoxy moieties. Their solubility in organic solvents, however, was improved by introducing the bulky pendent ether groups such as methoxy, phenoxy, and biphenoxy moieties into their repeating structure units. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 971–978, 1998     

Thermo-oxidatively stable polyimides and their chemical structures

A series of aromatic diamines having ether and/or carbonyl moieties in their structures were synthesized. By using these synthesized diamines and commercially available tetracarboxylic dianhydrides, various kinds of polyimides having ether and/or carbonyl moieties were synthesized. The thermo-oxidative stability of the obtained polyimides was investigated by focusing on the chemical structures of their repeating structure units. The reason for the improved thermo-oxidative stability of the ether–carbonyl polyimide structure was explained by an electronically balanced condition, i.e., the balance of electron donor moiety (—O—) and electron acceptor moiety (—CO—) in a chemical structure, and the degree of electron deficiency of the benzene–imide ring structure. The possibility of the formation of a charge transfer complex (CT-complex) was also mentioned as an explanation of the improved thermo-oxidative stability of ether–carbonyl polyimide structures. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1717–1723, 1998     

A positive-working photosensitive alkaline-developable polyimide with a highly dimensional stability and low dielectric constant based on poly(amic acid) as a polyimide precursor and diazonaphthoquinone as a photosensitive compound

A positive-working photosensitive polyimide precursor based on fluorinated poly(amic acid) (FPAA) and 2,3,4-tris(1-oxo-2-diazonaphthoquinon-4-ylsulfonyloxy)benzophenone (D4SB) as a photosensitive compound has been developed. FPAA was prepared by ring-opening polyaddition of dianhydrides, pyromellitic dianhydride and biphenyltetracarboxylic dianhydride, with diamine, 2,2′-bis(trifluoromethyl)benzidine, in methanol. The FPAA film showed excellent transparency to UV light and good solubility in a wide range of organic solvents. The dissolution behavior of FPAA containing 30 wt % D4SB after exposure was studied, and it was found that the difference of dissolution rate between exposed and unexposed parts was enough to get high contrast due to the photochemical reaction of D4SB in the polymer film. The photosensitive fluorinated polyimide (FPI) precursor containing 30 wt % D4SB showed a sensitivity of 80 mJ cm⁻² and a contrast of 7.8 with 365 nm light when it was developed with 0.3% aqueous tetramethyl ammonium hydroxide solution at room temperature. The FPI film cured up to 360°C had a low coefficient of thermal expansion of 10.3 ppm °C⁻¹ and a low dielectric constant of 3.04. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. A Polym. Chem. 36: 2261–2267, 1998     

Ion implant-induced change in polyimide films monitored by variable energy positron annihilation spectroscopy

6FDA-pMDA polyimide membranes were implanted with 140 keV N⁺ ions to fluences between 2 × 10¹⁴ and 5 × 10¹⁵ cm⁻². Variable energy positron annihilation spectra were taken and spectral features compared to previously reported changes in gas permeability and permselectivity of these membranes as a function of ion fluence. Positron data corroborate the explanation of these changes in terms of molecular damage caused by the implant: for fluences up to about 1 × 10¹⁵ cm⁻², the concentration of irradiation-induced defects merely increases with implant fluence; while fluences exceeding this threshold value create a second type of positron annihilation site, thereby marking a distinct change in the structure of the polymer, which is responsible for the vast improvement of gas permselectivity data found at the same threshold fluence. PACS codes: 78.70.Bj—positron annihilation; 61.82.Pv—polymers, organic compounds; 61.72.Ww—doping and impurity implantation. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2413–2421, 1998     

Miscibility and crystallization behavior of solution-blended PEEK/PI blends

Miscibility and crystallization behavior of solution-blended poly(ether ether ketone)/polyimide (PEEK/PI) blends were investigated by using DSC, optical microscopy and SAXS methods. Two kinds of PIs, YS-30 and PEI-E, which consist of the same diamine but different dianhydrides, were used in this work. The experimental results show that blends of PEEK/YS-30 are miscible over the entire composition range, as all the blends of different compositions exhibit a single glass transition temperature. The crystallization of PEEK was hindered by YS-30 in PEEK/YS-30 blends, of which the dominant morphology is interlamellar. On the other hand, blends of PEEK/PEI-E are immiscible, and the effect of PEI-E on the crystallization behavior of PEEK is weak. The crystallinity of PEEK in the isothermally crystallized PEEK/YS-30 blend specimens decreases with the increase in PI content. But the crystallinity of PEEK in the annealed samples almost keeps unchanged and reaches its maximum value, which is more than 50%. The spherulitic texture of the blends depends on both the blend composition and the molecular structure of the PIs used. The more PI added, the more imperfect the crystalline structure of PEEK. © 1998 John Wiley & Sons, Inc. J. Polym. Sci. B Polym. Phys. 36: 2267–2274, 1998     

Imidization and interdiffusion of poly(amic ethyl ester) precursors of PMDA/3,4′-ODA

Para-, meta-, and mixed isomeric poly(amic ethyl ester) precursors of the polyimide based on pyromellitic dianhydride (PMDA) and 3,4′-oxydianiline (3,4′-ODA) were synthesized. The intrinsic viscosity of each of the isomers was measured in an NMP solution and found to be less than corresponding isomers derived from PMDA and 4,4′-oxydianiline (4,4′-ODA) precursors with comparable molecular weight. The imidization and solvent retention were measured as a function of imidization temperatures, T_i using forward recoil spectrometry (FRES). For samples cast from a single solvent, either N-methyl pyrrolidone (NMP) or dimethyl sulfoxide (DMSO), no difference was observed in the temperature-dependent imidization behavior between the isomers. In all cases the imide fraction f increased as T_i increased, and reached a value of unity, i.e., full conversion at 400°C. At the same T_i, samples cast from DMSO showed a slightly higher f than samples cast from NMP. FRES and time of flight FRES (TOF-FRES) were used to measure the interdiffusion distance, w, of deuterium-labeled tracers into nondeuterated base layers of the polyimide of PMDA/3,4′-ODA treated at various T_i. The primary determinant of w for all isomers was T_i, and the particular isomer used as either the base or the tracer molecule did not seem to affect w. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2247–2258, 1998     

Diffusion in gas separation membrane materials: A comparison and analysis of experimental characterization techniques

Typically, materials with high-performance transport properties such as zeolites, carbon molecular sieves, or hyper rigid polymers are inherently difficult or impossible to characterize by steady-state membrane permeation experiments used for conventional polymers. Diffusion coefficients determined by transient sorption, a measurement easily performed on brittle media, are analyzed here and compared to those determined by steady-state permeation/sorption and transient permeation for a glassy polymer and a carbon molecular sieve. Average and local diffusion coefficients are extrapolated to zero upstream partial pressure to eliminate effects caused by concentration dependence. Good agreement between the techniques was observed for the glassy polymer. On the other hand, carbon molecular sieves, possessing a more complex morphology, exhibit a greater difference in diffusion coefficients determined by the various techniques. Nevertheless, comparison of the analysis techniques is shown to provide potentially valuable insights into the morphological features of such carbon molecular sieves. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1747–1755, 1998     

Synthesis and properties of polyimide-clay hybrid films

Polyimide-clay hybrid films with four different sizes of clay minerals have been synthesized to investigate the effect of the size of clay minerals to the properties of the hybrids. Hectrite, saponite, montmorillonite, and synthetic mica were used as clay minerals. Those clays consist of stacked silicate sheets about 460 Å (hectrite), 1650 Å (saponite), 2180 Å (montmorillonite), and 12300 Å (synthetic mica) in length, 10 Å in thickness. The longer the length of clay mineral was, the more effectively properties of polyimide were improved. In the case of polyimide-mica hybrid, only 2 wt % addition of synthetic mica brought permeability coefficients of water vapor to value less than one-tenth of that of ordinary unfilled polyimide, and thermal expansion coefficient was lowered at the level of 60% of the original one. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2289–2294, 1997