表面活性剂对纤维素接枝共聚物溶液粘度性质的影响

研究了阴离子十二烷基硫酸钠(SDS)、阳离子十六烷基三甲基溴化铵(CTAB)和非离子聚乙二醇辛基苯基醚(OP)等三种不同类型的表面活性剂对疏水化水溶性两性纤维素接枝共聚物(CGAO)溶液粘度性质的影响.结果表明,在SDS和OP的临界胶束浓度(cmc)附近，CGAO溶液粘度最大，SDS引起CGAO粘度的变化大于OP；即使在CTAB的cmc附近，随着CTAB浓度的增加，CGAO的粘度一直呈下降趋势；非疏水改性的纤维素接枝共聚物的溶液粘度随SDS或CTAB浓度的增加而下降，但几乎不随OP浓度的增大而变化.此外，通过凝胶渗透色谱法测得的保留时间证实了SDS、CTAB和OP与CGAO之间的疏水缔合作用.     

液晶聚酯与环氧嵌段共聚物的合成及表征

近年来 ,人们利用高分子液晶作为热固性环氧树脂的改性剂 ,不仅可以提高环氧树脂的韧性和强度 ,而且可以改善其热性能 ,为制备高性能的环氧树脂提供了一条新的途径[1,2 ] .目前报道所使用的液晶聚合物大多为液晶聚酯[3 ] 或液晶性聚氨酯[4] ,这些液晶聚合物与环氧树脂由于存在相容性不好的问题 ,给其实际应用带来了困难 .为了改善二者的相容性 ,本文采用溶液法合成了末端带有反应活性基团的聚酯型液晶聚合物 ,将它再与双酚Ａ环氧预聚物反应 ,制得了高分子液晶环氧嵌段共聚物 ,其合成路线如下 :2ＨＯＣＯＯＣＨ3+ ＨＯ(ＣＨ2 ) 6 ＯＨ　　Ｈ…     

醋酸乙烯酯-马来酸酐共聚物与水解聚丙烯酰胺高分子络合物的研究

<正> 某些高分子在溶液中可以通过次价力形成高分子络合物.根据次价力的不同,可分为四类:聚电解质络合物、氢键络合物、立体络合物和电荷转移络合物.部分水解聚丙烯酰胺(简称HPAM)是在水悬浮体中被广泛使用的絮凝剂,醋酸乙烯酯-马来酸酐共聚物(简称VAMA)是一种能力很强的泥浆稀释剂.研究二者在水溶液中的相互作用,在理论上和应用上都有重要意义.我们曾研究了粘土对它们的吸附作用、改变泥浆流变性以     

NMR SPECTROSCOPIC STUDY ON COPOLYMER OF ETHYLENE-NORBORNENE

A series of ethylene-norbornene copolymers were synthesised using VO (OEt) Cl_2/Al_2Et_3Cl_3 catalytic system and their structure was characterized by ~1H-NMR, ~1H-~1HCOSY NMR and ~(13)C-NMR. Assignments of NMR spectra were given and discussed indetail.     

PHOTO-INDUCED DOPED POLYANILINE BY THE VINYLIDENE CHLORIDE AND METHYL ACRYLATE COPOLYMER AS PHOTO ACID GENERATOR

The emeraldine base form of polyaniline (PANI) can be doped by a photo-induceddoping method. In this method a copolymer of vinylidene chloride and methyl acrylate(VCMAC) was used as photo acid generator which can release proton when it is exposedto ultraviolet light (λ= 254 nm). The structure of PANI-VCMAC system before and afterirradiation was characterized by elemental analysis, IR, XPS, and SEM images. Resultsobtained indicate that the photo-induced doping characteristics, such as doping positionand type of charge carriers, are similar to that of PANI doped with HCl. The poor room-temperature conductivity (～10~(-5)S/cm) of PANI-VCMAC system after irradiation maybe due to low doping degree (～pH= 3) and the difference in morphology as compared withPANI-HCl film.     

New PIM-1 copolymers containing 2,3,6,7-anthracenetetrayl moiety and their use as gas separation membranes

1. Download : Download high-res image (198KB)
2. Download : Download full-size image

     

甲基丙烯酸—磷脂酰乙醇甲基丙烯酰胺共聚物LB膜的研究

制备了不同摩尔比的甲基丙烯酸-磷脂酰乙醇甲基丙烯酰胺共聚物,研究了这种共聚物在水面的表面压力(π)-分子面积(A)曲线、共聚物制成的MOS LB膜的电容(C)-电压(V)特性及此LB膜的相变温度。     

用SN型催化剂合成苯乙烯一丙烯嵌段共聚物的研究──Ⅰ．聚合条件对共聚合反应的影响

用稀土化合物改性的钛系载体催化剂（ＳＮ催化剂）进行苯乙烯和丙烯顺序嵌段共聚合（Ｓｅｑｕｅｎｔｉａｌｂｌｏｃｋｃｏｐｏｌｙｍｅｒｉｚａｔｉｏｎ）的研究．考察了苯乙烯预聚时间、单体比、外加给电子体（ＥＢ）、烷基铝浓度、催化剂浓度和聚合温度等条件对共聚合的影响．发现外加酯（ＥＢ）降低了共聚合反应催化活性，在ＥＢ／Ｔｉ摩尔比为５范围内，外酯有助于提高嵌段共聚物（ｉＰＳ—ｂ—ｉＰＰ）中ＰＳ段和ＰＰ段的等规度及增加苯乙烯链节含量．ＳＮ型催化剂对苯乙烯一丙烯嵌段共聚合有较高的催化活性，催化效率在１００ｇ聚合物／ｇ－Ｔｉ以上．共聚物通过溶剂革取分级除去均聚物后，所得嵌段共聚物中苯乙烯链节含量可在１５～８５ｍｏｌ％之间调节．其结构表征续见第ＩＩ报．     

Morphology, crystallization behavior and properties of impact-modified polypropylene copolymer with or without sodium benzoate as a nucleating agent

 The morphology, crystallization behavior, and properties of an impact-modified polypropylene (PP) copolymer with or without sodium benzoate were investigated. The contents of ethylene–propylene rubber (EPR) in the reactor-made PP copolymer is about 15 wt%. For comparison, blends of PP and EPR containing the same EPR composition were prepared by melt-mixing. Morphological studies by scanning probe microscopy indicated that the impact-modified copolymer consists of three different phases, i.e., polyethylene, PP, and EPR phases, which is considerably different from the morphology of the conventional PP/EPR blend of the corresponding composition. The impact-modified PP copolymer exhibited a higher crystallization rate in terms of the lower crystallization half-time and thus higher thermal and mechanical properties, such as impact strength and hardness, than the PP/EPR blend did. The addition of sodium benzoate as a nucleating agent to the copolymer increased the crystallization rate and the mechanical properties. Received: 4 June 2001 Accepted: 31 October 2001     

Synthesis of poly[arylene ether sulfone-b-vinylidene fluoride] block copolymers

A series of α,ω-dihydroxy polyarylene sulfones (PAES) were synthesized comprising bisphenol A (PAES1, M_n=1800, 4900, and 9500 daltons), 4,4^′-biphenol (PAES2, M_n=4100 daltons), and hexafluorobisphenol A (PAES3, M_n=3300 daltons). These were reacted with α,ω-dibromo poly(vinylidene fluoride) (PVDF, M_n=1200 daltons) prepared by telomerization, to yield block copolymers possessing rigid and flexible segments. Block copolymers were characterized by FTIR, NMR, GPC, DSC, TGA and TEM. In several cases the block copolymers exhibited distinct thermal transitions, i.e. T_m and T_g for PVDF and PAES segments, respectively. Where observable, T_g of PAES domains in the block copolymers occurred at a temperature lower than the corresponding PAES homopolymer due to the flexible nature of the surrounding PVDF domains. Block copolymers exhibited a similar thermal stability to the corresponding PAES homopolymers but higher stability than the PVDF homopolymer, and much higher still than α,ω-dibromo PVDF. TEM analyses indicate that phase separation of PAES and PVDF domains occurs on the nanometer scale.