A New Nanocomposite Based on Pt-rGO Embedded Polymelamine Formaldehyde Nanocomposite for Reduction of Carbon Dioxide

Here, polymelamine formaldehyde was decorated on the surface of reduced graphene oxide whose surface was then electrodeposited with a sub-monolayer of platinum nanoparticles. The nanocomposite thus prepared was characterized using several spectroscopic methods. Using the nanocomposite as a potential electrocatalyst for carbon dioxide reduction, the products were detected by Raman spectroscopy, gas chromatography, ¹³C-NMR spectroscopy, and gas chromatography-mass spectrometry. The analytical results identified methanol as the main product of CO₂ reduction. Moreover, analysis of the liquid products confirmed methanol as the predominant product with a current density of 0.4 mA/cm and a Faradaic efficiency of 93 %.     

Performance Improvement of Acid Pretreated 3D-printing Composite for the Heavy Metal Ions Analysis

The performance enhancement of 3D-printed electrode comprised of polylactic acid (PLA) and graphite (Gr) doped with graphene oxide (GO) was studied to detect five heavy metal ions in trace level. The pretreatment of PLA/Gr/GO electrode with potential cycling in H₂SO₄ solution achieved the most sensitive response. The characteristics of the composite electrodes were verified using XPS, FE-SEM, EDXS, Raman, and impedance spectroscopy. The experimental variables affecting the response current were optimized with respect to pH, deposition time, ratio of PLA/Gr/GO, and supporting electrolytes. The pretreated 3D-PLA/Gr/GO electrode showed a wide dynamic range from 0.5 ppb to 1.0 ppm with low detection limits of 0.039–0.13 ppb. The reliability of the PLA/Gr/GO electrode was evaluated by analyzing the reference samples of European Reference Materials.     

Monitoring Imidazoline Derivatives via Functionalized Nano-Potentiometric Platforms in Aqueous Humor and Dosage Forms

The determination of two imidazoline derivatives [oxymetazoline HCl (OXY) and xylometazoline HCl (XYLO)] was described using different potentiometric platforms. The first electrode type was constructed using tetraphenyl borate (TPB) as anionic exchanger with β-cyclodextrins (β-CD) as ionophore forming oxymetazoline-tetraphenyl borate (OXY-TPB) and xylometazoline-tetraphenyl borate (XYLO-TPB), respectively. The second electrode type was prepared by modification of the first type by conjugation with magnetic iron oxide nanoparticles (MNP) forming (OXY-MNP) and (XYLO-MNP). The synthesized electrodes were fully characterized. The effect of magnetic nano-sized particles as a highly dispersible material with β-CDs on the electrode characteristics was investigated and compared against the classical electrodes. The response time, working pH range and selectivity coefficients were studied. The functionalized nano-electrodes (OXY-MNP and (XYLO-MNP) were found to be more sensitive than the classical electrodes with linearity ranges (1×10⁻⁶–1×10⁻² M). The functionalized nano-electrodes were successfully applied for the in-line analysis of OXY and XYLO in pharmaceutical dosage forms and spiked rabbit aqueous humor samples with no prior extraction of treatment. This suggests the future use of these electrodes in clinical studies of both drugs of interest.     

Development of Magnesium Anode-Based Transient Primary Batteries

Biodegradable primary batteries, also known as transient batteries, are essential to realize autonomous biodegradable electronic devices with high performance and advanced functionality. In this work, magnesium, copper, iron, and zinc – metals that exist as trace elements in the human body – were tested as materials for biomedical transient electronic devices. Different full cell combinations of Mg and X (where X = Cu, Fe, and Zn and the anodized form of the metals) with phosphate buffered saline (PBS) as electrolyte were studied. To form the cathodes, metal foils were anodized galvanostatically at a current density of 2.0 mA cm⁻² for 30 mins. Electrochemical measurements were then conducted for each electrode combination to evaluate full cell battery performance. Results showed that the Mg−Cu_anodized chemistry has the highest power density at 0.99 mW/cm². Nominal operating voltages of 1.26 V for the first 0.50 h and 0.63 V for the next 3.7 h were observed for Mg−Cu_anodized which was discharged at a current density of 0.70 mA cm⁻². Among the materials tested, Mg−Cu_anodized exhibited the best discharge performance with an average specific capacity of 2.94 mAh cm⁻², which is comparable to previous reports on transient batteries.     

Influence of the PVOH molar mass on the morphology and functional properties of EVOH/PVOH films prepared by melt blending

The influences of the molar mass (low, medium, and high) and content of poly(vinyl alcohol) (PVOH) dispersed by melt-blending in an ethylene vinyl alcohol (EVOH) copolymer on the morphology, microstructure, thermal, mechanical, and oxygen barrier properties were investigated. Multilayer films with external low-density polyethylene layers and inner EVOH/PVOH blend layer and respective monolayer films were elaborated and characterized. EVOH/PVOH blends exhibited a good compatibility because of the initial presence of PVOH segments in EVOH. The detailed quantitative analysis of the morphology performed for all blends showed that the finest dispersion was obtained with the PVOH with the lowest molar mass. The properties of the films as a function of the PVOH content and its molar mass were determined herein. Significant improvement of barrier properties was obtained at moderated water activities (up to a_w = 0.6) by using the PVOH with the lowest molar mass. Compared to the neat EVOH material, the oxygen permeability coefficients decreased by a factor 2 by adding 15 vol% PVOH while the thermal and mechanical properties remained similar.     

On the swelling behavior of poly(N-Isopropylacrylamide) hydrogels exposed to perfluoroalkyl acids

Per- and polyfluoroalkyl substances (PFAS) have rapidly accumulated in the environment due to their widespread use prior to commercial discussion in the early 21st century, and their slow degradation has magnified concerns of their potential toxicity. Monitoring their distribution is, therefore, necessary to evaluate and control their impact on the health of exposed populations. This investigation evaluates the capability of a simple polymeric detection scheme for PFAS based on crosslinked, thermoresponsive poly(N-isopropylacrylamide) (PNIPAM) hydrogels. Surveying swelling perturbations induced by several hydrotropes and comparable hydrocarbon analogs, tetraethylammonium perfluorooctane sulfonate (TPFOS) showed a significantly higher swelling ratio on a mass basis (65.5 ± 8.8 at 15°C) than any of the other analytes tested. Combining swelling with the fluorimetric response of a solvachromatic dye, nile red, revealed the fluorosurfactant to initiate observable aggregation (i.e., its critical aggregation concentration) at 0.05 mM and reach saturation (i.e., its charge neutralization concentration) at 0.5 mM. The fluorosurfactant was found to homogeneously distribute throughout the polymer matrix with energy dispersive X-ray spectroscopy, marking the swelling response as a peculiar nexus of fluorinated interfacial positioning and delocalized electrostatic repulsion. Results from the current study hold promise for exploiting the physiochemical response of PNIPAM to assess TPFOS's concentration.     

Optimal method for preparing sulfonated polyaryletherketones with high ion exchange capacity by acid-catalyzed crosslinking for proton exchange membrane fuel cells

Sulfonated polyaryletherketones (SPAEK) bearing four sulfonic acid groups on the phenyl side groups were synthesized. The benzophenone moiety of polymer backbone was further reduced to benzydrol group with sodium borohydride. The membranes were crosslinked by acid-catalyzed Friedel-Crafts reaction without sacrifice of sulfonic acid groups and ion exchange capacity (IEC) values. Crosslinked membranes with the same IEC value but different water uptake could be prepared. The optimal crosslinking condition was investigated to achieve lower water uptake, better chemical stability (Fenton's test), and higher proton conductivity. In addition, the hydrophilic ionic channels from originally course and disordered could be modified to be narrow and continuous by this crosslinking method. The crosslinked membranes, CS4PH-40-PEKOH (IEC = 2.4 meq./g), reduced water uptake from 200 to 88% and the weight loss was reduced from 11 to 5% during the Fenton test compared to uncrosslinked one (S4PH-40-PEK). The membrane showed comparable proton conductivity (0.01–0.19 S/cm) to Nafion 212 at 80°C from low to high relative humidity (RH). Single H₂/O₂ fuel cell based on the crosslinked SPAEK with catalyst loading of 0.25 mg/cm² (Pd/C) exhibited a peak power density of 220.3 mW/cm², which was close to that of Nafion 212 (214.0 mW/cm²) at 80°C under 53% RH. These membranes provide a good option as proton exchange membrane with high ion exchange capacity for fuel cells.     

Polymerization-induced self-assembly of amino-acid-based nano-objects by reversible addition–fragmentation chain-transfer dispersion polymerization

A series of amino-acid-based amphiphilic diblock copolymer nano-objects having different morphologies were developed by reversible addition–fragmentation chain-transfer (RAFT) dispersion polymerization of styrene (St) in methanol. This was mediated by six different hydrophilic poly(N-acryloyl amino acid) macro-chain transfer agents (CTAs), including three carboxylic-acid-containing ones, poly(N-acryloyl-l -proline) (PAProOH), poly(N-acryloyl-4-trans-hydroxy-l -proline) (PAHypOH), and poly(N-acryloyl-l -threonine) (PAThrOH) prepared by RAFT polymerization, and their methyl ester forms, PAProOMe, PAHypOMe, and PAThrOMe. The effects of polymerization conditions on RAFT dispersion polymerization of St using a dithiocarbamate-terminated PAProOH was investigated. A systematic study of the effects of monomer conversion and concentration afforded the formation of various morphologies (i.e., spheres, worms, and vesicles). The effects of hydrogen-bonding and ionic interactions of the macro-CTAs on the assembled structures of the nano-objects were evaluated using six different macro-CTAs. Transforming the products from methanol to water via dialysis produced amino-acid-based block copolymer nano-objects, exhibiting pH-responsive morphological change, in aqueous solution.     

Buffering effects on the solution behavior and hydrolytic degradation of poly(β-amino ester)s

With a vast, synthetically accessible compositional space and highly tunable hydrolysis rates, poly(β-amino ester)s (PBAEs) are an attractive degradable polymer platform. Leveraging PBAEs in a wide range of applications hinges on the ability to program degradation, which, thus far, has been frustrated by multiple confounding phenomena contributing to the degradation of these charged polyesters. Basic conditions accelerate hydrolysis, yet reduce solubility, limiting water access to amines and esters. Further, the high buffering capacity of PBAEs can render buffers ineffective at controlling solution pH. To unify understanding of PBAE degradation and solution properties, this study examines PBAE hydrolysis as a function of pH and buffer concentration as well as polymer hydrophobicity. At low buffer concentrations, the PBAE amines and the acid produced during hydrolysis control solution pH. Meanwhile, at high buffer concentrations that afford relatively constant pH, hydrolysis rate increases with pH, despite the reduced PBAE solubility. Increasing the hydrophobic content of PBAEs eventually hinders the capacity of the polymer to accept protons from solution, limiting the pH increase and slowing hydrolysis. These studies showcase the role of buffering on the pH-dependent degradation and solution properties of PBAEs, providing guidance for programming degradation in applications ranging from drug delivery to thermosets.     

Random copolymerization of macromonomers as a versatile strategy to synthesize mixed-graft block copolymers

The random copolymerization of norbornene-functionalized macromonomers was explored as a method of synthesizing mixed-graft block copolymers (mGBCPs). The copolymerization kinetics of a model system of polystyrene (PS) and poly(lactic acid) (PLA) macromonomers was first analyzed, revealing a gradient composition of side chains along the mGBCP backbone. The phase separation behavior of mGBCPs with PS and PLA side chains of various backbone lengths and side chain molar ratios was investigated, and increasing the backbone length was found to stabilize the phase-separated nanostructures. The graft architecture was also demonstrated to improve the processability of the mGBCP, compared to a linear counterpart. Investigations of mGBCPs comprised of polydimethylsiloxane and poly(ethylene oxide) side chains exemplified the diverse self-assembled morphologies, including a Frank-Kasper A15 phase, that can be obtained with mGBCPs synthesized by random copolymerization of macromonomers. Lastly, a ternary mGBCP was synthesized by the copolymerization of three macromonomers.