孔洞受压的统一极限分析

采用俞茂宏统一强度理论分别就平面应变和平面应力总是对受压孔洞进行了极限分析，得到了各自的统一解形式。以往的基于Ｔｒｅｓｃａ、Ｍｉｓｅｓ、双剪屈服准则以及Ｍｏｈｒ－Ｃｏｕｌｏｍｂ强度理论的极限解均为本文统一解的特例。此解可以适应于广泛的不同性质的各灯材料，合理也得出不同材料的相应解。     

Global Existence for Rate-Independent Gradient Plasticity at Finite Strain

We provide a global existence result for the time-continuous elastoplasticity problem using the energetic formulation. For this, we show that the geometric nonlinearities arising from the multiplicative decomposition of the strain can be controlled via polyconvexity and a priori stress bounds in terms of the energy density. While temporal oscillations are controlled via energy dissipation, the spatial compactness is obtained via regularizing terms involving gradients of the internal variables. Dedicated to Sir John Ball on the occasion of his 60th birthday.     

Degradation of aliphatic-aromatic copolyesters by bacteria that can degrade aliphatic polyesters

The degradation activities of bacteria that can degrade aliphatic polyesters on various aliphatic-aromatic copolyesters (PBSTIL, PBST, and Ecoflex™) were investigated. Among the bacteria examined, strain TB-71 showed the best degradation activity. An HPLC analysis of the degradation products revealed that PBST55 and Ecoflex™ are degraded into monomers by strain TB-71. In the case of PBSTIL, an unknown peak was detected by the HPLC analysis and was considered to be derived from water-soluble oligomers containing isophthalic acid segments. This finding seemed to be attributed to the chemical structure of the aromatic segments of the copolymers.     

Determination of melamine and related triazine by-products ammeline, ammelide, and cyanuric acid by micellar electrokinetic chromatography

In this study, micellar electrokinetic chromatographic (MEKC) methods were developed for the detection of traces of melamine and its related by-products (ammeline, ammelide, and cyanuric acid). Two on-line sample concentration steps namely reversed electrode polarity stacking mode (REPSM) and cation-selective injection (CSI) were used for improving the detection sensitivity. For REPSM, a borate-NaOH buffer (pH 10, 35 mM) composed of 60 mM SDS and 10% (v/v) methanol, was used as carrier electrolyte, and samples were prepared in an aqueous solution of 10 mM NaOH. In CSI, a phosphate buffer (pH 2, 50 mM) containing 41 mM SDS was used as the carrier electrolyte, and samples were prepared with an aqueous solution of 10 mM NaOH and a phosphate buffer (pH 2.0, 25 mM) in a volume ratio of 1:9. The results indicated that REPSM enhanced all analyte signals except for melamine, which could be concentrated only by the CSI. The detection limit was reduced from 1.7 mg L⁻¹ to 2.8 μg L⁻¹ for melamine by the optimal CSI step, and from 0.23-1.2 mg L⁻¹ to 2.4-5.0 μg L⁻¹ for the other three analytes by the optimal REPSM step. Tableware made of melamine and samples of flour were used as test samples, and the results indicated that the proposed MEKC methods can successfully determine contaminations from melamine. The study also indicated that when the plastic made of melamine was exposed only once to an acidic solution (acetic or phosphoric acid) at 80 °C for 30 min, melamine continuously leached out from the test sample even without any further treatment with an acidic solution.     

Computer controlled-flow injection potentiometric system based on virtual instrumentation for the monitoring of metal-biosorption processes

A completely automated flow-injection system was developed for the monitoring of biosorption studies of Cu(II) ion on vegetable waste by-products. The system employed flow-through Cu(II)-selective electrodes, of epoxy-resin-CuS/Ag₂S heterogeneous crystalline type, and computer controlled pumps and valves for the flow operation. Computer automation was done through a specially devised virtual instrument, which commanded and periodically calibrated the system, allowing for the monitoring of Cu(II) ions between 0.6 and 6530 mg L⁻¹ at a typical frequency of 15 h⁻¹. Grape stalk wastes were used as biosorbent to remove Cu(II) ions in a fixed-bed column with a sorption capacity of 5.46 mg g⁻¹, obtained by the developed flow system, while the reference determination performed by FAAS technique supplied a comparable value of 5.41 mg g⁻¹.     

合肥光源托歇克效应损失电子的探测

 束流寿命是衡量储存环性能的重要参数,直接影响着光源的正常运行。对于合肥光源（HLS）,托歇克（Touschek）寿命是影响束流寿命的重要因素。为了研究Touschek寿命,需要探测由于Touschek效应所损失的电子。介绍了束流寿命的概念,说明了Touschek效应的原理和机制,利用蒙特卡罗软件EGSnrc模拟计算了丢失电子与真空壁的相互作用,通过塑料闪烁体探测器和光电倍增管获得了由于Touschek效应丢失的电子所产生的信号,然后将信号经过放大甄别和符合处理后,用计数器测量了计数率。结果表明：由于Touschek效应而成对丢失的电子的确存在,且电子损失率随流强的降低而减小。这为下一步储存环的能量标定工作做好了前期准备。     

Cosmic ray test for a T0 detector

The endcap of time-of-flight (ETOF) detector in BES (Beijing Spectrometer) III is planned to be upgraded by using multi-gap resistive plate chambers (MRPCs) and the designed time resolution of the MRPCs is around 50 ps. Thus a time-zero (T0) detector needs to be built to offer a high quality reference time for the MRPCs beam test. So a T0 detector is built using plastic scintillator tiles (BC420) to couple with four fast phototubes (PMTs, Hamamatsu H6533). The timing properties of the detector is studied by using a cosmic ray test and factors related to the time resolution, such as plastic scintillator size, readout mode and angle effects, are discussed. T0 detector timing resolutions of ～41-62 ps are achieved, which means that the T0 detector can be used in the MRPC beam test.     

各向异性弹塑性中厚度板壳的有限元分析

本文在文献［２，３］的基础上，提出了一个解各向异性弹塑性中厚度板壳问题的有限元方法。考虑材料各向异性的特点，采用了Ｈｉｌｌ推广的Ｈｕｂｅｒ－Ｍｉｓｅｓ屈服准则；借用Ｏｗｅｎ的剪切修正系数，正确计及了叠层复合材料壳体的横向剪切效应；为了避免“自锁”现象，文中采用了９节点的Ｈｅｔｅｒｏｓｉｓ二次壳单元；特别是本文利用插值外推的思想，提出了一个带预测的弧长增量控制法，显著提高了确定变形路径的计算效率。几个数值算例表明本文给出的有限元方法对于各向异性中厚度板壳的弹塑性分析有较好的精度，尤其是对具有复杂变形路径的结构计算，收敛速度提高更快。     

金属切屑塑性流动的稳定性

对金属正交切削过程中切屑形成机制和材料塑性流动行为进行实验研究和理论分析. 通过对4 种常用金属材料正交切削过程的实验研究和切屑形貌的微观观察,确定了连续切屑转变成锯齿切屑的临界速度. 结果表明该临界速度与材料性能相关. 在实验观察基础上,提出描述材料正交切削过程的二维分析模型. 该模型假设切屑形成区为包括主剪切区和次剪切区的一个平行四边形. 载荷有主剪切区中的剪应力和次剪切区中的正压力;通过量纲分析得到描述材料正交切削过程的无量纲主控参数和无量纲形式的基本控制方程;应用线性稳定性分析方法建立平面应变状态下评价材料塑性流动稳定性的普遍准则;求得切屑形成区内材料塑性变形的速度和应力近似解. 讨论切屑形成、形貌转变以及相关的塑性失稳机制. 分析结果表明, 表征材料惯性与阻尼之比的无量纲参数— 雷诺数可以作为主控参数描述金属切削过程以及切屑材料塑性流动的稳定性.      

High-energy x-ray diffraction study on phase transition asymmetry of plastic crystal neopentylglycol

As a prototype material of colossal barocaloric effects, neopentylglycol is investigated by combining high-precision differential scanning calorimetric measurement and high-energy x-ray diffraction measurement. The diffraction data at constant temperatures indicate a first-order phase transition with thermal hysteresis as well as the phase transition asymmetry, specifically, the phase transition is completed faster at cooling than at heating. The analysis of resulting pair distribution function confirms the intermolecular disorder in the high-temperature phase. The phase transition asymmetry is quantitatively characterized by time-resolved x-ray diffraction, which is in agreement with the thermal measurement. Also, such an asymmetry is observed to be suppressed at high pressures.