手性二茂铁聚酰胺催化剂的合成及应用

以二茂铁为原料,经酰化、氧化和酰氯反应得到二茂铁二酰氯继而与手性二氨作用合成未见文献报道的三种新的手性二茂铁聚酰氨配体。其Ｒｈ（Ｉ）配合物催化苯乙酮的不对称氢转移化应应得到高的转化率,ｅ．ｅ．值１６．５％。新化合物的结构通过元素分析,核磁共振及红外光谱得到确证。     

Nanocomposites from Untreated Clay : A Myth ?

Polyamide 6 and pristine montmorillonite have been melt blended in an extruder and water was injected into the melt in order to produce nanocomposites. The pristine clay was found to be exfoliated and dispersed homogenously in the nanocomposites. A mechanism explaining the formation of such nanocomposites is presented.     

Chain Extension of Polyamide 6 Using Bisoxazoline Coupling Agents

The chain extension behaviors of 2,2′-(1,3-phenylene)bis(2-oxazoline) (MPBO) and 2,2′-bis(2-oxazoline) (BOZ) were studied to evaluate the coupling effect on polyamide 6 (PA6) in a Haake Rheocord mixer and an extruder. The coupling results showed that there existed an optimal dosage of chain extender, lack of which caused deficiency of chain extension and excess of which led to more blocking reaction. The effect of chain extension with MPBO was shown to be inferior to BOZ. When the optimum amount of chain extenders was added in PA6, the intrinsic viscosity of the polyamide 6 increased from 1.632dl/g to 1.787dl/g(MPBO) and 2.031dl/g(BOZ), respectively. The reaction time decreased very fast with an increase in the temperature. The chain-extended products dissociated at high temperature; the degradation is suggested to proceed from the onset of the chain extension reaction, as do the coupling and blocking reactions. Furthermore, the effects of MPBO and BOZ on the thermal and mechanical properties of chain-extended PA6 were also investigated.     

氧化铜和聚磷酸铵对聚酰胺6热降解行为的影响

氧化铜和聚磷酸铵对聚酰胺6热降解行为的影响     

Polyamide 6‐polycaprolactone multiblock copolymers: Synthesis,characterization, and degradation

This work describes the synthesis and characterization of polyamide 6 (PA 6)‐polycaprolactone (PCL) multiblock copolymers. Low molar mass, fully amine end‐capped PA 6 was prepared by the addition of a diamine monomer during ε‐caprolactam polymerization. A low molar mass PCL was selected to be incorporated as the biodegradable block and was fully end‐capped with toluene 2,4‐diisocyanate. End group analysis and molecular weight characterizations were performed for both end‐functionalized polymers by SEC, NMR and titration analysis. Incorporation of PCL into PA 6 was mainly achieved by solution mixing of the two end‐functional blocks and, was continued after the removal of the solvent with solid state polymerization (SSP) by gradual heating until about 40 °C below the melting temperature of the PA 6. Molecular weights started to grow immediately during solution mixing and only increased marginally during the SSP treatment. FTIR and SEC studies confirmed the reaction between the two components. DSC data, in combination with the enhanced molar mass during solution mixing pointed to a blocky microstructure, for which distinct melting and crystallization temperatures were observed for the PCL and the PA 6 blocks. Hydrolytic and enzymatic degradation studies were performed at 25 °C where the degree of degradation was followed by weight loss analysis, SEM and SEC. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

末端带有溴甲基基团的柱状树枝化聚酰胺的合成与表征

采用大分子单体的方法合成了一种含大量溴甲基官能团端基,主链和侧链均为聚酰胺的功能化柱状树枝化聚酰胺.氯化亚砜的新活化工艺使整个合成过程不需要保护和去保护的步骤且减少了副反应的产生,从而使得合成和纯化更加简单.产物的结构通过红外和核磁得到了证实.由分子量测试知,聚酰胺的重均分子量(Mw)为5.01×104,分子量分布为2.74.由溶解性测试知,该聚合物能溶解于N,N′-二甲基甲酰胺、N,N′-二甲基乙酰胺、二甲亚砜、1-甲基-2-吡咯烷酮和硫酸等溶剂,溶解性能得到了大大的提高,主要是由于侧链树枝化单元和末端溴甲基存在的缘故.由粘度测试知,该聚酰胺的粘度低,主要是由于侧链树枝化单元的屏蔽效应.该聚合物的热性能也由TGA测试得到了表征,结果表明该聚酰胺具有良好的热性能.由于该聚酰胺外端具有大量的溴甲基基团,它可以作为原子转移自由基聚合反应的引发剂来合成大型的梳形聚合物,另外通过把它外围的溴甲基转化为其它的功能化基团,可以使它应用于其它更广的领域.     

Preparation and nonisothermal crystallization behavior of polyamide 6/montmorillonite nanocomposites

Polyamide 6 (PA6)/montmorillonite (MMT) nanocomposites were prepared via melt intercalation. The structure, mechanical properties, and nonisothermal crystallization kinetics of PA6/MMT nanocomposites were investigated by X‐ray diffraction (XRD), tensile and impact tests, and differential scanning calorimetry (DSC). Before melt compounding, MMT was treated with an organic surfactant agent. XRD traces showed that PA6 crystallizes exclusively in γ‐crystalline structure within the nanocomposites. Tensile measurements showed that the MMT additions are beneficial in improving the strength and the stiffness of PA6, at the expense of tensile ductility. Impact tests revealed that the impact strength of PA6/MMT nanocomposites tended to decrease with increasing MMT content. The nonisothermal crystallization DSC data were analyzed by Avrami, Ozawa, modified Avrami‐Ozawa, and Nedkov methods. The validity of these empirical equations on the nonisothermal crystallization process of PA6/MMT nanocomposites is discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2878–2891, 2004     

Melt spinning and laser‐heated drawing of a new semiaromatic polyamide,PA9‐T fiber

Fibers of PA9‐T, a new semiaromatic polyamide containing a long aliphatic chain, were prepared by melt spinning. As‐spun fibers were subsequently drawn with a CO₂ laser‐heated drawing system at different draw ratios and various drawing velocities. On‐line observations of drawing points deciphered two drawing states; namely, flow drawing and neck drawing, over the entire range of drawing. Drawing stress revealed that flow drawing is induced by slight drawing stress under a low draw ratio up to 3, and neck drawing is induced by relatively high drawing stress under a higher draw ratio. The effect of drawing stress and drawing velocity on the development of the structure and properties has been characterized through analysis of birefringence, density, WAXD patterns, and tensile, thermal, and dynamic viscoelastic properties. For the neck‐drawn fibers, almost proportional enhancements of crystallinity and molecular orientation with drawing stress were observed. The flow‐drawn fibers have an essentially amorphous structure, and birefringence and density do not always have a linear relation with properties. The fibers drawn at high drawing speed exhibit improved fiber structure and superior mechanical properties. The maximum tensile strength and Young's modulus of PA9‐T drawn fibers were found to be 652 MPa and 5.3 GPa, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 433–444, 2004     

Postcondensation and oxidation processes in molten polyamide 6

Polyamide samples were heated under vacuum or mixed in a Brabender plastograph. UV absorbance, chain end concentration, and molecular weight were studied. Postcondensation was observed for polyamide heated under vacuum. For polyamide samples mixed in the plastograph, atmosphere, shear rate, and temperature changed. Melt viscosity and intrinsic viscosity are in good correlation in a log-log plot. Oxidation effect on molecular weight and amine chain end concentration could be well related to UV absorbance. The oxygen diffusion into the molten polyamide is a critical parameter. The oxygen concentration in the polyamide mixed under air is ca. 20 times higher than when mixed under nitrogen. The introduction of preoxidized material in the molten polyamide or mixing in the presence of oxygen have similar effects. Postcondensation and oxidation strongly influence the melt behavior of polyamides. © 1993 John Wiley & Sons, Inc.     

Synthesis of block copolymer containing dextran and polyamide sequences

A novel AB-type block copolymer composed of dextran and polyamide sequences was prepared through the following two approaches. One is a coupling reaction of a terminal functional group introduced in the dextran chain with that in the polyamide chain, such as the reaction of an amine group with an acyllactam group or that of a lactone group with an amine group at the corresponding chain ends. The other is an anionic polymerization of a bicyclic lactam activated with a trimethylsilylated dextran derivative having an acyllactam end group. The latter procedure was found to be more effective for the preparation of the block copolymer having a high molecular weight polyamide sequence.