AES investigations of the iron surface composition after laser irradiation under atmospheric conditions

The laser induced modification of iron surfaces with atmospheric species was investigated by means of Auger electron spectroscopy (AES) and scanning electron microscopy (SEM). Different laser systems were used for irradiating iron samples in a wide range of the laser processing parameters up to small foci and ultra short pulses.A nitriding of iron connected with an oxidation of the near surface region was observed in the wavelength range between 193 nm and 10.6 m using large foci (0.1 cm²) and short pulses (10...1400ns). In case of small foci (7·10^–6cm²) with ns-pulses (50 ns) an enrichment of the iron melt with nitrogen and an advanced oxidation of the surrounding area of the laser spot were detected. When using shorter pulses (200 fs, 40 ps) no indications for a nitriding were found.     

Quantitative millimetre wavelength spectrometry at pressures approaching atmospheric: II. Determination of oxygen at atmospheric pressure

A millimetre wavelength (MMW) Fabry-Perot cavity spectrometer described in earlier work has been applied to the measurement of oxygen absorption at 60 GHz and atmospheric pressure in a gas matrix of nitrogen. The spectrometer has also been modified such that the MMW source is stabilised by a sub-harmonic microwave signal transmitted by an infrared carrier on a single mode telecommunications fibre optic. This is a step towards developing an instrument comprising minimal electronic components that can perform MMW spectrometry remotely. Oxygen determinations were achieved by monitoring the change in the quality factor (Q) of a resonant Fabry-Perot cavity due to the presence of an absorbing sample. The MMW absorption of the sample was determined by incrementing the frequency modulation (FM) deviation of the source frequency scanning the cavity resonance profile. The response curve of absorption signal versus fraction of oxygen in nitrogen was found to be linear throughout the working range of 1-100% O₂ (v/v) in N₂ with a slope of (1.407±0.007)×10⁻⁴ m⁻¹ (% O₂)⁻¹. The detection limit (3× standard deviation of the background) was found to be ∼0.8% (v/v). The MMW technique employed is advantageous since, unlike common MMW techniques, there is no vacuum requirement. Application of this method, to the monitoring of oxygen in gas mixtures of practical importance, is proposed. Values of the oxygen spectral absorption coefficients of lines between 55 and 60 GHz were measured at reduced pressure and found to be within ±2% of previous literature values. A pressure correction coefficient for O₂ absorption at 60 GHz in the 45-121 kPa range was obtained and found to be (1.354±0.014)×10⁻⁴ m⁻¹ kPa⁻¹.     

Salting coefficients for gases in seawater from scaled-particle theory

Experimental values of the salting coefficients for He, Ne, Ar, O₂, and N₂ in seawater are compared with values calculated from scaled-particle theory. The agreement is reasonably good; the average difference between calculated and observed values at 25°C is 0.007. Scaled-particle theory predicts correctly thatk _s should decrease as the temperature increases and that this effect should be most pronounced at low temperatures. However, the predicted magnitude ofdK _s/dt is only about half of that observed.     

1，2－二氢－3H－吲哚－3－酮类化合物的光化学合成

１，２－二氢－３Ｈ－吲哚－３－酮类化合物的光化学合成凌可庆（淮北煤炭师范学院化学系，淮北，２３５０００）关键词吲哚衍生物，单重态氧反应，１，２－二氢－３Ｈ－吲哚－３－酮衍生物，光合成１，２－二氢－３Ｈ－吲哚－３－酮是重要的有机合成中间体，广泛用于多种...     

光学薄膜氧气传感器研究进展

光学薄膜氧气传感器具有检测精度高、选择性好、抗干扰能力强等优点,近年来日益得到人们的广泛重视,研究工作也在不断深化和拓展,展现出十分广阔的应用前景。本文按光学薄膜氧气传感器的制备方法分类扼要综述了光学薄膜氧气传感器的研究现状,并展望了其研究前景。     

锰—铈复合氧化物催化剂表面氧的性质

氧化锰催化剂广泛用于一氧化碳常温氧化及汽车尾气的净化等,CeO_2是氧化物催化剂的优良助剂。非贵金属催化剂中添加CeO_2能提高催化剂的氧化活性已有很多报道,但有关Ce对氧化锰结构及表面氧脱附性能影响的研究尚不多见。本文运用XRD、DTA和TPD-MS等手段对共沉淀法制得的Mn-Ce复合氧化物进行了物相结构和脱氧活性研究。     

cotpp-pt/c作直接甲醇燃料电池阴极催化剂

四苯基钴卟啉;pt催化剂;直接甲醇燃料电池;氧还原     

合成重要中间体1,4位官能化化合物的简便方法

5,6-取代环烯醚2在乙腈的单重态氧反应有效的生成一系列1,4位官能化化合物3。1,4位官能化化合物为合成上重要的中间体。环烯醚2可以通过β-二酰基化合物1和1,3-二溴丙烷在稀碱(碳酸钾/丙酮)条件下缩合生成。