Mechanical Properties of Blends of Low-Density Polyethylene with Chlorinated Polyethylene

The results of experimental investigation into the mechanical properties of blends of low-density polyethylene (LDPE) with chlorinated polyethylene (CPE) in tension are presented. The specimens of pure LDPE, CPE, and nine types of LDPE/CPE blends, with different content of components at 10 wt.% intervals, were examined. Data on the influence of blend composition on the tensile stress-strain diagram, elastic modulus, yield stress, breaking stress, and ultimate elongation are obtained. The results of investigations of creep are also reported. It is found that the creep compliance (the total current compliance minus the elastic compliance) obeys the power law of creep.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 3, pp. 391–404, May–June, 2005.     

The Modeling of Velocity Enhancement in Polymer Flooding

In single-phase polymer flooding experiments it has repeatedly been observed that the average velocity of the polymer molecules is higher than the average velocity of the water molecules. This effect is incorporated in many conventional Enhanced Oil Recovery (EOR) simulators by the introduction of a constant velocity enhancement factor. In this paper we show that, in absence of dispersion, a constant enhancement factor in the mathematical model for two-phase polymer flow (Buckley--Leverett displacement) leads to ill-posedness of the model equations. We propose a saturation dependent enhancement factor, derived from a model based on percolation concepts, for which this problem does not occur.     

A highly selective solid phase extraction sorbent for pre-concentration of sameridine made by molecular imprinting

Summary A novel approach to solid phase extraction, based on the use of a highly selective molecularly imprinted polymer, is presented. The versatility of this type of sorbent for solid phase extraction was demonstrated in a model batch-wise pre-concentration of sameridine prior to gas chromatography. Problems associated with leakage of remaining imprint molecules during the desorption phase could be eliminated by the use of a close structural analogue of sameridine as the imprint species. It was found that a major benefit of the imprinted polymer was its specificity, which lead to distinctly cleaner chromatographic traces and ability to improve sensitivity by extracting sameridine from larger sample volumes.     

Structural characterization of polypyrrole in the solid state by high resolution 15N NMR spectroscopy [II]

The solid-state ¹⁵N CP/MAS NMR spectra and ¹⁵N spin-lattice relaxation times (T₁) of doped and dedoped ¹⁵N-labeled polypyrroles prepared by electrochemical polymerization, have been measured by means of high-resolution solid-state ¹⁵N NMR. The ¹⁵N signal of polypyrrole consists of four peaks decomposed by line shape analysis. The four peaks obtained have been assigned to the various structures of polypyrrole. Further, the half-width of the ¹⁵N NMR spectra of polypyrroles is discussed as related to the electrical conductivity. © 1995 John Wiley & Sons, Inc.     

Aqueous solution and solid state interactions of lanthanide ions with a methacrylic ester polymer bearing pendant 15‐crown‐5 moieties

The interaction between trivalent lanthanide ions and poly(1,4,7,10,13‐pentaoxacyclopentadecan‐2‐yl‐methyl methacrylate), PCR5, in aqueous solution and in the solid state have been studied. In aqueous solution, evidence of a weak interaction between the lanthanides and PCR5 comes from the small red shift of the Ce(III) emission spectra and the slight broadening of the Gd(III) EPR spectra. From the Tb(III) lifetimes in the presence of H₂O and D₂O the loss of one or two water coordinated molecules is confirmed when Tb(III) is bound to PCR5. An association constant of the order of 200 M^?1 was obtained for a 1:1 (lanthanide:15‐crown‐5) complex from the shift of the polymer NMR signals induced by Tb(III). A similar association constant is obtained from the differences of the molar conductivity of Ce(III) solution at various concentrations in presence and absence of PCR5. When Tb(III) is adsorbed on PCR5 membranes, lifetime experiments in H₂O and D₂O confirm the loss of 5 or 6 water coordinated molecules indicating that in solid state the lanthanide(III)‐PCR5 interaction is stronger than in solution. The adsorption of Ce(III) in PCR5 membranes shows a Langmuir type isotherm, from which an equilibrium constant of 39 M^?1 has been calculated. SEM shows that the membrane morphology is not much affected by lanthanide adsorption. Support for lanthanide ion–crown interactions comes from ab initio calculations on 15‐crown‐5/La(III) complex. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1788–1799, 2007     

Developing a hybrid emulsion polymerization system to synthesize Fe3O4/polystyrene latexes with narrow size distribution and high magnetite content

A hybrid emulsion polymerization was formulated for synthesizing Fe₃O₄/polystyrene composite latex. This system, containing binary droplets that are magnetic (Mag)‐droplets with a diameter of 100–200 nm and styrene (St)‐droplets with a diameter of 3–4 μm, was obtained by mixing Mag‐miniemulsion and St‐macroemulsion. With extremely low surfactants concentration (?critical micelle concentration, CMC), the nucleated loci are selectively controlled in the Mag‐droplets, as the result of smaller droplet size and larger surface ratio. Both water‐soluble potassium persulfate (KPS) and oil‐soluble 2,2′‐azobis(2‐isobutyronitrile) was adopted to initiate the polymerization. In the presence of KPS, magnetic polystyrene latices with particles size of 60–200 nm, narrow size distribution, and high magnetite content (86 wt % measured by TGA) were attained successfully. The synthesized magnetic Fe₃O_4/polystyrene latices assembled into well‐ordered hexagonal structure in the surface of a carbon supported copper grid. The influence of various parameters on various aspects of the as‐synthesized Fe₃O₄/polystyrene was investigated in detail: type of initiator on composite morphology, feed ratio of Mag‐miniemulsion and St‐macroemulsion on magnetite content, and hydrophobic agent or amount of surfactant on size and size distribution. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5285–5295, 2007     

Synthesis,dynamic light scattering,and luminescence properties of copolymers containing iridium(III) bisterpyridine in the side chain

Supramolecular block‐random copolymers containing [Ir(terpy)₂]³⁺ in the side chain were synthesized via postfunctionalization of a P(S‐b‐AC_terpy) block copolymer. Absorbance and emission spectra compared to a model compound show that the polymer backbone has a minor effect on the polymer absorbance but produces a larger shift for the phosphorescence signals to higher wavelength. Dynamic light scattering of the metal complex containing copolymer studied in various solvents showed monomodal aggregation with decreasing aggregate size as the solvent dielectric constant increased. The copolymer precursor P(S‐b‐AC_terpy) shows multimodal aggregation in different solvents with the major population consisting of single chains. This difference in behavior between the two polymers is attributed to the electrolytic nature of the complex and the amphiphilicity induced by the charged metal complex. Supramolecular copolymers like these will continue to have interesting self‐organizational properties and may find applications in multicomponent systems for photoinduced charge separation processes. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1109–1121, 2007     

Photoinitiated curing of mono‐ and bifunctional epoxides by combination of active chain end and activated monomer cationic polymerization methods

Photoinitiated cationic polymerization of mono‐ and bifunctional epoxy monomers, namely cyclohexeneoxide (CHO), 4‐epoxycyclohexylmethyl‐3′,4′‐epoxycyclohexanecarboxylate (EEC), respectively by using sulphonium salts in the presence of hydroxylbutyl vinyl ether (HBVE) was studied. The real‐time FTIR spectroscopic, gel content determination, and thermal characterization studies revealed that both hydroxyl and vinyl ether functionalities of HBVE take part in the polymerization. During the polymerization, HBVE has the ability to react via both active chain end (ACE) and activated monomer mechanisms through its hydroxyl and vinyl ether functionalities, respectively. Thus, more efficient curing was observed with the addition of HBVE into EEC‐containing formulations. It was also demonstrated that HBVE is effective in facilitating the photoinduced crosslinking of monofunctional epoxy monomer, CHO in the absence of a conventional crosslinker. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4914–4920, 2007     

光纤放大器增益饱和对有源光纤环形腔滤波特性的影响

从理论和实验两个方面研究了有源光纤环形腔滤波器输入光功率对光纤放大器增益的影响及由此引起的对有源光纤环形腔滤波特性的影响。在考虑上述影响的情况下 ,对有源光纤环形腔滤波器参数的优化作了讨论     

Phase Conjugation in Saturable Absorbing Dye Films by Degenerate Four-Wave Mixing and Holographic Processes Using Nanosecond Pulse and CW Lasers

We report on the simultaneous generation of phase-conjugate signals by degenerate four-wave mixing (DFWM) and holographic processes using a nanosecond pulse and a CW lasers in polyvinyl alcohol (PVA) films doped with four kinds of saturable absorbing dyes. For the pulse laser, of the four kinds of dye-doped PVA films, the erythrosine B-doped PVA and uranine doped-PVA films generate PC signals only by the DFWM process, while the other dye-doped PVA films generate PC signals simultaneously by not only the DFWM process but also the holographic process. Especially, the safranin T-doped PVA film generates strong PC signals by the holographic process. In contrast, all of the dye-doped PVA films generate the two types of PC signals for the CW laser. The fading of dye molecules is found to result in the generation of the holographic component of PC signals which governs the temporal behavior of the total PC signals.