Studies on adhesion characteristics and corrosion behaviour of vinyltriethoxysilane/epoxy coating protective system on aluminium

The corrosion stability of vinyltriethoxysilane/epoxy coating protective system on aluminium is strongly related to the strength of bonds forming at the metal/organic coating interface. This article is a study of adhesion, composition, electrochemical and transport properties of epoxy coatings electrodeposited on bare aluminium and aluminium pretreated by vinyltriethoxysilane (VTES) during exposure to 3% NaCl. The VTES film was deposited on aluminium surface from 2% vinyltriethoxysilane solution during 30 s. From the values of adhesion strength (pull-off test), time dependence of pore resistance and coating capacitance of epoxy coating (impedance measurements) and diffusion coefficient of water through epoxy coating (gravimetric liquid sorption measurements), the influence of VTES sublayer on the corrosion stability of the electrodeposited epoxy coating was shown.The work discusses the role of the VTES pretreatment in the enhanced adhesion and corrosion stability of epoxy cataphoretic coating. The electrochemical results showed that the aluminium pretreatment by VTES film improved barrier properties of epoxy coating (greater pore resistance and lower coating capacitance). The lower value of diffusion coefficient of water through epoxy coating indicates the lower porosity, while the smaller adhesion reduction points to better adhesion of epoxy coating on aluminium pretreated by VTES film. The composition of the deposited coatings investigated by XPS enabled the clarification of the bonding mechanism.     

Corrosion behavior and composition analysis of chromate passive film on electroless Ni-P coating

A passive film was formed on electroless Ni-P coating (ENPC) in a bath of K₂Cr₂O₇ 30 g/l. XPS and electrochemical methods were employed to analyze its chemical compositions and corrosion behaviors. The potentiodynamic polarization tests indicated the corrosion current of the passivated sample was 1/30 that of as-plated ENPC. The XPS analysis illustrated the film comprised Cr, Ni and O. The film thickness was evaluated to be a few nanometers according to the sputtering rate of Ar⁺ ion. High-resolution XPS spectra suggested that the detected Cr in film was in the form of trivalent compounds, Cr₂O₃ and Cr(OH)₃.     

Improved performance of TiO2 electrodes coated with NiO by magnetron sputtering for dye-sensitized solar cells

TiO₂ electrodes are coated with NiO by DC magnetron sputtering, and their structural, optical and electrochemical performance has been investigated. X-ray diffractometry (XRD), UV-vis spectrophotometry, scanning electron microscopy (SEM), AC impedance, and linear sweep voltammetry (LSV) are used to characterize the TiO₂/NiO electrodes. Their performance is evaluated with a computer controlled electrochemical workstation in combination with three conventional electrodes. The experimental results indicate that the surface modification of TiO₂ electrodes with sputtered NiO reduces trap sites on TiO₂ and improves the electrochemical performance of dye-sensitized solar cells (DSSCs). Sputtering NiO for 7 min, which is about 21 nm thick, on 6.5 μm thick TiO₂ greatly improves the DSSC parameters, and the conversion efficiency increases from 3.21 to 4.16%. Mechanisms of the influence of the NiO coating on electrochemical performance are discussed.     

Graded index broadband antireflection coating prepared by glancing angle deposition for a high-power laser system

This paper reports that SiO₂ is selected to fabricate broadband antireflection (AR) coatings on fused silica substrate by using glancing angle deposition and physical vapour deposition. Through accurate control of the graded index of the SiO₂ layer, transmittance of the graded broadband AR coating can achieve an average value of 98% across a spectral range of 300--1850~nm. Moreover, a laser-induced damage threshold measurement of the fabricated AR coating is performed by using a one-on-one protocol according to ISO11254-1, resulting in an average damage threshold of 17.2~J/cm$^{2}$.     

在有机玻璃上射频溅射ITO组合薄膜

利用射频磁控溅射技术在有机玻璃表面上一次完成表面活化、ITO膜制备、SiO2 减反射膜制备过程。利用低能等离子体对有机玻璃表面进行改性以提高ITO膜的附着力。研究了氧分压等工艺参数对ITO膜导电性能及光学性能的影响。     

具有鲁棒性的矩形窄带滤光片的自动设计

分析了用于WDM光纤通信系统的全介质多腔窄带滤光片的膜系结构特点及其所必须具备的光学特性,提出了一种利用最优化方法的原理,通过计算机寻优来自动完成其膜系设计的方法;构造了合理的评价函数,编制了可自动搜索既满足设计目标、又具有鲁棒性的最优化膜系的计算机程序;使用本程序所设计出的多腔窄带滤光片具有较小的纹波系数和较好的矩形度,可满足WDM光纤通信系统对其分波/复波器的要求.     

Scanning tunneling lithography of silicon nanoparticle films

Monolayer and bi-layer silicon nanoparticle (SiNP) films with wide band gaps (up to 4 eV) have been produced in UHV with narrow size distributions of particles with 2-4 nm diameters and were studied using scanning tunneling microscopy (STM) and spectroscopy (STS). The films then were manipulated by applying different values for the tunneling resistance. Nanoparticle fusion and fission processes allow to shape the particles in the films in various ways and to write in white and black on the film template.     

Synthesis and Optical Properties of SiO2-Coated CeO2 Nanoparticles

Silica (SiO₂)-coated ceria (CeO₂) nanoparticles were prepared using water-in-oil microemulsion. Polyoxyethylene (15) cetylether and cyclohexane were used as a surfactant and organic solvent. SiO₂-coated CeO₂ nanoparticles were obtained by hydrolysis of metal alkoxide (tetraethylorthosilicate, TEOS) in the solution containing CeO₂ precursor nanoparticles. The effects of CeO₂ sources (Ce metal salt) and CeO₂ particle-forming agents on the morphology of SiO₂–CeO₂ particles were investigated. Observation via transmission electron microscopy revealed that the type of particle-forming agent affected the nanoparticles' morphology and that CeO₂ nanoparticles were spherically coated with SiO₂ when using oxalic acid ((COOH)₂) as a particle-forming agent of CeO₂. Furthermore, the transmittance of the particles was high in the visible region (above 400 nm) and decreased in the ultraviolet region.     

基于SSPCM的新型储能型太阳能蒸馏器实验研究

本文基于定型相变材料(SSPCM)建立了新型储能型太阳能蒸馏器的实验系统,并分别对普通SSPCM和高导热SSPCM的蒸馏特性进行了实验研究.研究发现:与传统太阳能蒸馏器相比,基于普通SSPCM的储能型蒸馏器的日产量提升了 7.5％,采用高导热SSPCM的日产量提升了 39％.此外,本文还对蒸馏器结构进行了优化研究,研制...     

纳米尺度下毛细流动的分子动力学模拟

采用分子动力学模拟研究纳米尺度下壁面润湿性对毛细流动的影响,主要考虑纳米通道两侧壁面润湿性相同与不同两种情况。研究表明：两侧壁面润湿性相同条件下,毛细流动随着壁面润湿性增强而加快, 毛细高度随时间的变化早期偏离Lucas-Washburn理论,但后期与其预测符合。在纳米通道两侧壁面润湿性不同的情况下,液面会发生振荡,两侧壁面毛细高度也不相等,且液面振荡的幅度和两侧壁面毛细高度差都随着两侧壁面润湿性差异的增大而增大。基于能量转化分析,提出两侧壁面湿润性不同情况下纳米通道中毛细流动发生的条件以及毛细流动快慢的判别依据。研究结果加深了对纳米尺度下毛细流动机理的认识,并为相关工程应用提供理论参考。