Molecular Assembly by Sequential Ionic Adsorption of Nanocrystalline TiO2 and a Conjugated Polymer

Abstract

Cationic nanocrystalline TiO₂ particles have been synthesized for which the size and composition of the nanoparticles were analyzed by a transmission emission microscopy and energy dispersive x‐ray spectrometer (EDXS). Multilayered films have been fabricated by sequential adsorption of TiO₂ nanoparticles and poly(3‐thiophene acetic acid) (PTAA). Each layer of the nanoparticles and PTAA in the thin film has also been characterized by x‐ray photoelectron spectroscopy, atomic force microscopy, and UV‐visible spectroscopy. These types of multilayered nanocomposite films may find applications in the fabrication of efficient light harvesting photovoltaic cells.     

Photo‐Oxidation of sPP/Organoclay Nanocomposites

Photo‐oxidation of syndiotactic polypropylene–sPP/organoclay nanocomposites was performed. Nanocomposites were prepared in situ by melt compounding of sPP, compatibilizer (iPP grafted with maleic anhydride–iPP‐g‐MAN) and organoclay filler ME C18 (modified with octadecyl ammonium chains in intergaleries of layered silicate, of which silicate layers (about 1 nm thin) were exfoliated). The influence of ME C18 nanoparticles alone (in content region 1 to 15 wt%) and together with compatibilizer iPP‐g‐MAN on the photostability of the sPP nanocomposite was studied. It was found that the silicate ME C18 nanoparticles alone catalyze the photooxidation and shorten the induction period of photo‐oxidation to one fourth (at the content of 5 wt% of ME C18) in comparison with unfilled sPP) and the presence of compatibilizer supports the photo‐oxidation of sPP nanocomposite. The ME C18 nanoparticles decrease the efficiency of UV stabilizers. The rate of photo‐oxidation of sPP/clay nanocomposite after the induction period is significantly higher than unfilled sPP. The mechanism of photo‐oxidation is discussed.     

Preparation and Characterization of Poly Vinyl Alcohol/Poly Vinyl Pyrrolidone/Clay Based Nanocomposite by Gamma Irradiation

A series of PVA/PVP/clay nanocomposite were prepared by gamma irradiation with different clay contents of (0.15, 0.3, 1, 1.5, 3 and 5 wt%). The gelation content and swelling behavior were investigated. The morphology and structure of PVA/PVP/clay nanocomposite and dispersion of the clay nanoparticles in the polymeric matrix were examined by infrared spectroscopy (FT-IR) and scanning electron microscopy (SEM). The introduction of clay into polymeric matrix was investigated by X-ray diffraction pattern (XRD) and Transmission electron microscope (TEM). It is observed that, the increase of the clay content causes a decrease in the swelling percent. The thermal stability studies confirmed that the introduction of clay lead to an increase in the thermal stability. The TEM results showed that the clay nanoparticles are interchelated or exfoliated in the polymeric matrix. Some desirable characteristics such as relatively good swelling and excellent barrier capability against microbe penetration suggested that PVA/PVP/clay nanocomposite can be a good candidate as a wound dressing.     

Modeling Diffusion in Foamed Polymer Nanocomposites

Two‐way multicomponent diffusion processes in polymeric nanocomposite foams, where the condensed phase is nanoscopically reinforced with impermeable fillers, are investigated. The diffusion process involves simultaneous outward permeation of the components of the dispersed gas phase and inward diffusion of atmospheric air. The transient variation in thermal conductivity of foam is used as the macroscopic property to track the compositional variations of the dispersed gases due to the diffusion process. In the continuum approach adopted, the unsteady‐state diffusion process is combined with tortuosity theory. The simulations conducted at ambient temperature reveal distinct regimes of diffusion processes in the nanocomposite foams owing to the reduction in the gas‐transport rate induced by nanofillers. Simulations at a higher temperature are also conducted and the predictions are compared with experimentally determined thermal conductivities under accelerated diffusion conditions for polyurethane foams reinforced with clay nanoplatelets of varying individual lamellar dimensions. Intermittent measurements of foam thermal conductivity are performed while the accelerated diffusion proceeded. The predictions under accelerated diffusion conditions show good agreement with experimentally measured thermal conductivities for nanocomposite foams reinforced with low and medium aspect‐ratios fillers. The model shows higher deviations for foams with fillers that have a high aspect ratio.     

三维连续结构Li4Ti5O12/石墨烯纳米复合材料：制备和其锂离子电池超长循环性能

利用具有三维连续纳米孔结构的热剥离石墨烯为骨架制备Li4Ti5O12/石墨烯纳米复合材料。通过乙醇挥发法在热剥离石墨烯的纳米孔道内引入前驱物,进一步高温热处理,在热剥离石墨烯的孔道内原位形成Li4Ti5O12纳米粒子。利用复合材料作为锂离子电池电极材料。电化学反应过程中,热剥离石墨烯的三维连续结构确保了Li4Ti5O12纳米粒子与石墨烯在长循环过程中的有效接触。因此,复合材料表现出优异的循环稳定性。在5C下,5 000次循环后,其容量保持率高达94%。     

还原氧化石墨烯/碳纳米管/Co_3O_4三元复合材料的制备与电化学性能

将低温水热反应和低温热处理相结合,制备了含还原氧化石墨烯(RGO)、碳纳米管(CNTs)和Co3O4的三元纳米复合材料RGO-CNTs-Co3O4;利用X射线衍射仪、扫描电子显微镜、透射电子显微镜分析了合成产物的相组成和微观结构,分析了其形成过程;并利用电化学测试装置测定了其作为锂离子电池负极材料的电化学性能.结果表明,在合成反应过程中,氧化石墨烯被还原剂肼还原为石墨烯,同时在石墨烯和CNTs表面生成氢氧化钴;再经低温热处理得到RGO-CNTs-Co3O4三元复合材料.Co3O4纳米颗粒均匀分散在由RGO片层和CNTs组成的三维网络结构中;这种三维网络结构既有利于电子和离子的传输,又能够有效抑制Co3O4在脱嵌锂过程中因体积变化引起的结构破坏.总体而言,合成的新型三元复合材料具有高的比容量以及良好的循环性能与倍率性能.     

Polymeric Nanocomposites—Polyhedral Oligomeric Silsesquioxanes (POSS) as Hybrid Nanofiller

Abstract

Polyhedral oligomeric silsesquioxane (POSS), a hybrid nanostructured macromer has been used in the last decade for preparation of polymeric nanocomposites. Its versatile chemistry, which lends it for almost infinite chemical modification, sets it apart from other nanostructured fillers like nanoclays, carbon nanotubes, and carbon nanofibers. Depending on its functionality, 3‐D network, bead or pendant type‐POSS based polymeric nanocomposites can be synthesized. These have the potential to be designed for products with specific nanostructures for specific end‐use applications. This article discusses the trends in current research involving use of POSS macromers for modification of mainly thermal and viscoelastic properties of various polymers.     

Graphene grafted silica‐coated Fe3O4 nanocomposite as absorbent for enrichment of carbamates from cucumbers and pears prior to HPLC

In this paper, a novel graphene (G) grafted silica‐coated Fe₃O₄ nanocomposite was fabricated by the chemical bonding of G onto the surface of silica‐coated Fe₃O₄ nanoparticles. Some carbamates (metolcarb, carbaryl, pirimicarb, and diethofencarb) in cucumber and pear samples were enriched by this nanocomposite prior to their determination by HPLC with UV detection. Experimental parameters that may affect the extraction efficiency were investigated. Under the optimum conditions, a linear response was achieved in the concentration range of 0.5–100.0 ng/g for metolcarb, carbaryl, and diethofencarb, and 1.0–100 ng/g for pirimicarb with the correlation coefficients (r) ranging from 0.9956 to 0.9984. The LOD (S/N = 3) of the method were found to be in the range from 0.08 to 0.2 ng/g. The RSDs were in the range from 2.4 to 5.8%. The results indicated that the G grafted silica‐coated Fe₃O₄ nanocomposite was stable and efficient for magnetic SPE and has a great application potential for the preconcentration of other organic pollutants from real samples.     

CuO‐CeO2 Nanocomposite: A Highly Efficient Recyclable Catalyst for the Green Synthesis of 1,8‐Dioxooctahydroxanthenes in Water

CuO‐CeO₂ nanocomposite is reported as a highly efficient and recyclable catalyst for the green synthesis of 1,8‐dioxooctahydroxanthenes in water. This catalyst can be recovered by simple filtration and recycled up to 8 consecutive runs without any losing of its efficiency.