Effect of surface nanocrystallization induced by fast multiple rotation rolling on hardness and corrosion behavior of 316L stainless steel

A nanostructured layer was fabricated by using fast multiple rotation rolling (FMRR) on the surface of 316L stainless steel. The microstructure in the surface was characterized by transmission electron microscopy and X-ray diffraction. The effects of FMRR on the microhardness, surface roughness and corrosion behavior of the stainless steel were investigated by microhardness measurements, surface roughness measurements, potentiodynamic polarization curves and pitting corrosion tests. The surface morphologies of pitting corrosion specimens were characterized by scanning electron microscopy. The results show that FMRR can cause surface nanocrystallization with the grain size ranges from 6 to 24 nm in the top surface layer of the sample. The microhardness of FMRR specimen in the top surface layer remarkably increases from 190 to 530 HV. However, the surface roughness slightly rises after FMRR treatment. The potentiodynamic polarization curves and pitting corrosion tests indicated that the FMRR treated 316L stainless steel with a surface nanocrystallized layer reduced the corrosion resistance in a 3.5% NaCl solution and enhanced the pitting corrosion rate in a FeCl₃ solution. Possible reasons leading to the decrease in corrosion resistance were discussed.     

Investigation of the voltage and time effects on the formation of hydroxyapatite-containing titania prepared by plasma electrolytic oxidation on Ti-6Al-4V alloy and its corrosion behavior

Producing titania and hydroxyapatite (HA) bioceramic coating on titanium alloys increases corrosion resistance and biocompatibility of these alloys. Plasma electrolytic oxidation (PEO) is one of the effective techniques for producing this type of coating. This method produces coatings with enough thickness and appropriate adhesion. In this study, titania and HA were directly produced on Ti-6Al-4V by applying PEO process in a Ca- and P-containing electrolyte by changing voltage and time parameters. Morphology and cross section, chemical composition and elements of coatings were investigated by scanning electron microscope, X-ray diffraction and energy dispersive spectroscopy, respectively. Corrosion behavior of the samples was also examined by potentiodynamic polarization and electrochemical impedance spectroscopy. The results indicated that the formation of HA phase with titania needs a minimum voltage below which HA is not formed. By increasing the operation time, the amount of the formed HA increased. Also, the sample coated at 500 V and 15 min showed the best corrosion behavior in Ringer's solution.     

The electronic transport properties in C60 molecular devices with different contact distances

By applying non-equilibrium Green?s functions in combination with the density-functional theory, we investigate the transport behavior of molecular devices composed by metal electrode-C₆₀ molecule-metal electrode. Our results show that the electronic transport properties are affected obviously by the different contact distances between the electrodes, and the tunneling current decreases approximately exponentially at a certain bias with the increasing of contact distances. The negative differential resistance is observed and the peak-to-valley ratio can be tuned by different contact distances. The mechanisms of the contact distance effect and the negative differential resistance behavior are proposed.     

Annealing effect on magnetic anisotropy in ultrathin（Ga,Mn）As

We investigated the effect of low temperature annealing on magnetic anisotropy in 7-nm ultrathin Ga0.94Mn0.06As devices by measuring the angle-dependent planar Hall resistance(PHR).Obvious hysteresis loops were observed during the magnetization reversal through the clockwise and counterclockwise rotations under low magnetic fields(below 1000 Gs,1 Gs = 10-4 T),which can be explained by competition between Zeeman energy and magnetic anisotropic energy.It is found that the uniaxial anisotropy is dominant in the whole measured ferromagnetic range for both the as-grown ultrathin Ga0.94Mn0.06As and the annealed one.The cubic anisotropy changes more than the uniaxial anisotropy in the measured temperature ranges after annealing.This gives a useful way to tune the magnetic anisotropy of ultrathin(Ga,Mn)As devices.     

Comparative investigation of resistance and ability to trigger high voltage discharge for single and multiple femtosecond filaments in air

A comparative investigation of resistance and ability to trigger high voltage (HV) discharge for single filament (SF) and multiple filaments (MF) has been carried out. The experimental results show that the trend of the breakdown threshold of the SF exactly follows that of its resistance, but this is not the case for the MF. The MF's resistance is much smaller than SF's. However, the MF shows a bit higher HV breakdown threshold than the SF. The underlying physics is that the measured resistance of the MF is collectively contributed by every filament in the MF while the HV breakdown threshold is determined by only one single discharging path.     

车用潜热贮热器的流动与换热实验研究

本文通过对车用潜热贮热器流动与换热实验研究，获得了该相变过程的流动、传热特性，为修正该装置的设计提供了可靠的数据．     

Influence of gamma radiation on morphology structure,electrochemical corrosion behavior and hardness of Ni–Cr based alloys

This study evaluates the effects of gamma radiation on structure, electrochemical corrosion behavior and Vickers hardness of commercial dental Nikkeli–Kromi–Polttosekoitus [Ni_65.2Cr_22.5Mo_9.5X_2.8 (X=Nb, Si, Fe and Mn)] alloy. The corrosion rate of Ni_65.2Cr_22.5Mo_9.5X_2.8 (X=Nb, Si, Fe and Mn) alloy with 0.5 M HCl is increased with increasing the exposure rate of gamma radiation. The corrosion resistance of Ni_65.2Cr_22.5Mo_9.5X_2.8 (X=Nb, Si, Fe and Mn) is varied and reaches a minimum value at 30 KGy. The corrosion potential value also is varied and reaches its highest value at 30 KGy. The Vickers hardness value of Ni_65.2Cr_22.5Mo_9.5X_2.8 (X=Nb, Si, Fe and Mn) alloy is decreased by increasing the gamma radiation dose. Also it is obvious from our results that the effects of gamma radiation at the surface are much higher as compared with deeper parts and the structure of the alloy is changed due to its exposure to gamma radiation.     

Nd0.7Sr0.3MnO3中显微结构相关电致电阻效应

用固相反应和高能球磨合成后续热处理两种方法分别得到钙钛矿结构Nd_0.7Sr_0.3MnO₃氧化物.两种不同方法得到的多晶样品,虽然晶体结构相同,化学成分和晶粒大小相近,但它们电输运性质却表现出很大差异.用固相反应法制得的样品的电阻几乎不随负载电流的变化而变化,即不表现电致电阻行为;而通过高能球磨合成后续热处理方法得到的样品电阻随外加电流增大而急剧减小,出现显著电致电阻效应.产生这种截然不同电输运特性的原因可能与样品的显微结构和界面性质有关. 关键词： 电致电阻效应 显微结构 钙钛矿结构锰氧化物 界面电阻     

大功率半导体激光器阵列热串扰行为

以硬焊料传导制冷,30%填充因子半导体激光器阵列为例,建立了三维有限元模型,对阵列内部各发光单元之间的热串扰行为进行了分析研究。结果表明,当其连续波工作时间大于1.2 ms后,阵列内发光单元之间出现热串扰现象;当次热沉由CuW合金改为铜金刚石复合材料时,阵列内发光单元自热阻和相邻发光单元的串扰热阻降低,有效地降低了各发光单元之间的热串扰行为。保持阵列宽度、发光单元数目及发光单元周期不变,发现随阵列填充因子的增加,器件热阻以指数衰减趋势逐渐降低,而发光单元间的热串扰特性对此变化并不敏感;保持阵列单个发光单元输出功率,发光单元尺寸及阵列宽度不变,增加发光单元个数后,阵列内各发光单元之间热串扰加剧,填充因子越高阵列升温速率越快;但在最初约70 s内,包含不同数目发光单元的阵列最高温度差异仅约0.5 ℃,有利于多发光单元高填充因子器件高功率输出。     

离心泵快速启动过程外部特性的试验研究

介绍离心泵快速启动试验装置和试验方法,对一台出口直径为80 mm的小型管道离心泵进行试验研究,分别测试了试验泵的稳态性能和各项瞬态性能,比较分析了两者的区别。结果显示,启动过程中,离心泵的扬程紧跟转速到达最大值,转速稳定后的瞬态性能与稳态假设对应,流量和扬程的上升历程与管路阻力特性直接相关,而转速与其基本无关; 在启动初始阶段,无量纲扬程呈现很大值,继而迅速减小到低于稳态假设值,表现出明显的瞬态效应。