Polytetrafluoroethylene and metal structure convective-flow CO laser

A convective flow CO laser composed of polytetrafluoroethylene discharge tubes, nickel–chromium steel components, a cupric heat exchanger and other components is described. Operating in liquid nitrogen condition, output power of 60 W has been obtained from a non-selective cavity.     

Liquid-phase noncatalytic butene oxidation with nitrous oxide

The kinetics and mechanism of noncatalytic liquid-phase oxidation of but-1-ene and but-2-ene with nitrous oxide in a benzene solution in the temperature range from 180 to 240°C were studied. Oxidation proceeds via the 1,3-dipolar cycloaddition mechanism to form carbonyl compounds. Both of these reactions occur with close rates and activation energies and have the first orders with respect to the alkene and N₂O. A considerable fraction (39%) of but-1-ene involved in oxidation undergoes cleavage at the double bond yielding propanal and an equivalent amount of methylene, the latter producing ethylcyclopropane and cycloheptatriene. The oxidation of but-2-ene proceeds with a minimum bond cleavage and affords methyl ethyl ketone with 84% selectivity. Regularities of the oxidation of terminal and internal alkenes C₂—C₈ with nitrous oxide were analyzed using the previously published data. __________ Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 4, pp. 925–933, April, 2005.     

Fiber-Optic Chemical Sensor for Detection of NO2 Using Poly (3-Octylthiophene)

A fiber-optic chemical sensor (FOCS) for detection of nitrogen dioxide (NO₂) molecules is reported. The FOCS presents an optropode structure because of the transmission properties of the sensitive material. The NO₂ FOCS is activated by using the semiconductor polymer: regioregular head-to-tail poly(3-octylthiophene-2,5-diyl). The operation wavelength of the sensor is 543.5 nm such that a simple LED and detector can be used for the design of this device. The sensor response decreases after each exposure, demonstrating the reduction in sensitivity as well as irreversibility lower than 5%. However, its properties such as rapid response, high selectivity, high sensitivity (0.43 ± 0.01 muW/ppm), hygroscopic properties, and its operation at room temperature make this kind of FOCS a good alternative for NO₂ toxic gas detection.     

Single to 16-Channel Wavelength Conversion at 10 Gb/s Based on Cross-Gain Modulation of ASE Spectrum in SOA

A simple scheme for single to multi-channel wavelength conversion based on cross-gain modulation of amplified spontaneous emission (ASE) spectrum in semiconductor optical amplifier (SOA) is described. Single to 16-channel wavelength conversion at 10 Gb/s is first demonstrated without any additional probe lights, the modulation information carried by input signal could be converted into arbitrary many channels if only the demultiplexer with enough channels is exploited. Output performance and pattern effects are investigated experimentally.     

Roles of rhenium diimine complexes as metal‐ion probes and photosensitizers in functional polyurethanes

Polyurethanes incorporated with rhenium diimine complexes were synthesized. The polymers exhibited interesting morphologies and solution properties. Results from gel permeation chromatography suggested the formation of polymer aggregates in solutions. The polymers could act as probes for metal ions. The addition of metal ions to polymer solutions led to significant changes in the electronic absorption properties of the polymer solutions. This was attributed to the interactions between the polyether moieties and metal ions. The metal complexes could also act as efficient photosensitizers. After doping with charge‐transport viologens, the photoconductivity of the polymers was greatly enhanced. The experimental quantum efficiency was simulated with Onsager's theory. The thermalization distances and the primary yields were typically 12–14 Å and 10^?3, respectively. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1708–1715, 2003     

On a new calcium vanadate: synthesis, structure and Li insertion behavior

A synthetic form of the mineral hewettite was prepared via a new route in aqueous medium, starting either from the crystalline compound Li_1.1V₃O₈, or from its amorphous precursor. The anhydrous, crystalline derivative Ca_0.5V₃O₈ was obtained by heating the synthetic hewettite at 250°C under dynamic vacuum. The diffraction studies show that the 2D structure of Ca_0.5V₃O₈ involves the same V₃O₈ layers as in the hewettite or in Li_1+αV₃O₈. The stacking of the layers is similar to that in the metahewettite. A structural model is proposed, where the Ca²⁺ ions occupy octahedral sites in the interlayer space. The electrochemical behavior of Ca_0.5V₃O₈ vs. lithium insertion is presented. It is original and reveals particularly good performances in terms of stability during cycling at C/5 rate. The homologues obtained with Mg or Ba, instead of Ca, are briefly presented.     

Dicyclopentadienyl complexes of titanium,niobium, and tungsten in the controlled synthesis of poly(methyl methacrylate)

Organometallic compounds Cp₂TiCl₂, (EtC₅H₄)₂NbCl₂, and (PrⁱC₅H₄)₂WCl₂ were assessed as additives that control polymer chain growth in the polymerization of methyl methacrylate. In the presence of compounds mentioned in amounts comparable with that of the initiator, a uniform process with no gel-effect occured and respective linear increase in the molecular weight of the polymer up to high degrees of the monomer conversion was observed.     

过渡金属表面γ-氨丙基三甲氧基硅烷膜的研究

本文对在过渡金属铁、镍电极表面制备得到的γ-氨丙基三甲氧基硅烷(γ-APS)膜进行了研究。实验中对硅烷膜用X-射线光电子能谱(XPS)、现场表面增强拉曼散射光谱(SERS)和原子力显微镜(AFM)进行了表征。X-射线光电子能谱(XPS)的结果发现存在两个N1s峰,表明γ-APS膜中的氨基有两种存在方式:自由氨基和质子化氨基。实验中还发现现场表面增强拉曼散射光谱(SERS)是研究金属/γ-APS体系中界面层结构非常有效的手段,SERS结果表明硅醇羟基和氨基发生了竞争吸附,且γ-APS分子在外加电位等条件的影响下吸附状态会发生一定变化。原子力显微镜(AFM)的表征结果在微观上显示电极表面的γ-APS膜上形成了一种较规则的微孔结构,这种结构可能与基底的性质有关。     

FAST ACCURATE PREDICTION OF BLANK SHAPE IN SHEET METAL FORMING

By using the Finite Element Inverse Approach based on the Hill quadratic anisotrop-ically yield criterion and the quadrilateral element, a fast analyzing software-FASTAMP for the sheet metal forming is developed. The blank shapes of three typical stampings are simulated and compared with numerical results given by the AUTOFORM software and experimental results, respectively. The comparison shows that the FASTAMP can predict blank shape and strain distribution of the stamping more precisely and quickly than those given by the traditional methods and the AUTOFORM.     

A Semiconductor Laser of the Visible Range as an Exciting Source of Raman Scattering

A possibility of application of semiconductor lasers of the visible range as exciting sources for Raman spectroscopy is studied. An experimental set-up for measuring Raman spectra of polycrystalline dielectrics and broad-gap semiconductors excited by a semiconductor laser with a wavelength of 640 nm was created. The conditions under which the spectral width of the lasing line of a semiconductor laser was within 10^-3 cm^-1 in the continuous mode with a power of 10 mW are realized. The characteristics of various types of exciting sources used in Raman spectroscopy are compared. The results of studies of the characteristic Raman spectra excited with a semiconductor laser in polycrystalline sulfur are presented.