Metal-support interaction in mesoporous silica supported cobalt Fischer-Tropsch catalysts

Summary The pore structure of silica supports (SiO₂ or MCM-41) has little influence on the metal-support interaction in silica supported cobalt catalysts. Cobalt dispersion, reduction behavior, and catalytic properties for the Fischer-Tropsch synthesis were primarily affected by the metal particle size.     

Improving MCM‐41 as a Nitrosamines Trap through a One‐Pot Synthesis

Copper oxide was incorporated into MCM‐41 by a one‐pot synthesis under acidic conditions to prepare a new mesoporous nitrosamines trap for protection of the environment. The resulting composites were characterized by XRD, N₂ adsorption–desorption, and H₂ temperature‐programmed reduction techniques, and their adsorption capabilities were assessed in the gaseous adsorption of N‐nitrosopyrrolidine (NPYR). The adsorption isotherms were consistent with the Freundlich equation. The copper salt was deposited onto MCM‐41 during the evaporation stage and was fixed on the host in the calcination process that followed. MCM‐41 was able to capture NPYR in air below 373 K but not at 453 K. Loading of copper oxide on MCM‐41 greatly improved its adsorption capability at elevated temperatures. The influence of the incorporation of copper into MCM‐41 samples and the adsorption behavior of these samples are discussed in detail.     

Zr-MCM-41的合成及其表征

以Zr(NO3)4·3H2O为锆源，通过直接合成法得到了Zr-MCM-41介孔材料，考察了不同Zr/Si摩尔比对样品的影响，其中Zr/Si的摩尔比最大为0.25。随着Zr/Si的摩尔比的增加，2θ=2°附近的100晶面的衍射峰强度逐渐降低，当Zr/Si摩尔比大于0.25后得不到介孔Zr-MCM-41材料。对所得样品采用XRD、TG-DTA、N2吸附 脱附几种分析方法进行了表征。     

负载型纳米TiO2复合载体及其CoMo催化剂的酸性及孔特性的研究

总结了复载不同纳米尺度的复合载体及其CoMo催化剂的表面酸性及孔结构特性的表征结果。结果表明，负载型纳米TiO2与基载体γ-Al2O3存在着相互作用。当负载比较少量的纳米TiO2时，复合载体的总酸量随着TiO2含量的增加而增加，超过γ-Al2O3的酸量，但当 TiO2的含量比较高时复合载体的酸量又降低，纳米TiO2优先负载在γ-Al2O3的强酸中心位；负载了CoMo活性组分后酸量增加。不同粒径的纳米TiO2对复合载体和催化剂的酸分布没有明显影响，但对总酸量有影响。对不同尺度TiO2，随着TiO2负载量的增加以及负载金属活性组分的增加，表面积、孔容和最可几孔径均有不同程度的减少。     

Preparation of Titania from Tetrakis(diethylamino)titanium via Hydrolysis

The conversion of tetrakis(diethylamino)titanium (Ti(NEt₂)₄) into titania via either a combination of hydrolysis (Ti(NEt₂)₄ : THF : H₂O = 1 : 10 : x, x = 2, 4, 10) at ambient conditions and calcination (method A) or hydrolysis in a water-tetrahydrofuran (THF) mixture (Ti(NEt₂)₄ : THF : H₂O = 1 : 10 : 100) at reflux (method B) was investigated. Titanium tertiary butoxide (Ti(O ^t Bu)₄) was also used as a substitute for Ti(NEt₂)₄. The hydrolysis via method A resulted in the formation of amorphous solids containing organics. Thermal analyses showed that the hydrolysis products showed mass losses up to 500°C probably due to the presence of diethylamine (Et₂NH) formed via the hydrolysis of Ti(NEt₂)₄ in the hydrolysis products, while a mass loss of the hydrolysis product from Ti(O ^t Bu)₄ was completed up to about 200°C. After calcination at 600°C, anatase or a mixture of anatase and rutile was obtained. The crystallization behavior of the hydrolysis products from Ti(NEt₂)₄ was different from that of the hydrolysis product from Ti(O ^t Bu)₄. The hydrolysis via method B gave only an amorphous material from Ti(NEt₂)₄, while a crystalline titania (anatase and brookite) formed from Ti(O ^t Bu)₄.     

Temperature programmed desorption analysis of sol-gel-derived titania films

Sol-gel-derived titania films were analyzed by temperature programmed desorption (TPD) and X-ray diffraction (XRD) techniques. The relationship between the TPD curves measured for two types of titania gel films and their crystal structures was investigated. On the basis of the analyses, a preparation process for a titania sol solution containing anatase nanocrystals was designed and developed. Using this process, a colloidal anatase titania sol solution was prepared by heating aqueous titanium hydroxide containing HCl at 60°C for 2 h. The nanocrystal structure of the titania films obtained by coating the sol on glass substrates was confirmed by TPD and XRD measurements.     

TiO2/Eu-MCM纳米超分子材料的组装和光催化性能

利用有机相-水相界面共沉淀溶胶支持自组装方法制备粒径为15 nm、孔径为8 nm的分子筛Eu-MCM, 它拥有734 m²/g的比表面积和1.49 cm³/g的比孔容. 把TiO₂组装到Eu-MCM的孔道中, 组装成TiO₂/Eu-MCM纳米复合材料. XRD, RAMAN和选区电子衍射花样分析表明纳米复合材料中的TiO₂为锐钛型. TiO₂/Eu-MCM的发光表现为Eu^3＋离子的特征光谱, 激发峰分别为342 (⁵L₁₀), 358 (⁵L₉), 378 (⁵L₇), 390 (⁵L₆), 411 (⁵D₃), 462 (⁵D₂)和524 (⁵D₁) nm; 发射峰为579, 592, 613, 653和701 nm, 归属于⁵D₀→⁷F_J (J＝0, 1, 2, 3, 4)组态间的跃迁. 纳米复合材料的发光强度都要比Eu-MCM的发光强, 其中43%TiO₂/Eu-MCM的发光最强. 荧光和紫外漫反射结果表明客体TiO₂对主体分子筛存在能量传递效应. 在微弱的紫外灯光照射下, TiO₂/Eu-MCM纳米复合材料对苯酚的光催化氧化性能和其发光强度具有一定的相关性. 29%TiO₂/Eu-MCM的纳米复合材料拥有的比表面积、孔容和孔径分别为204 m²/g, 0.24 cm³/g和4.7 nm. 29%TiO₂/Eu- MCM对苯酚具有68%的最高光催化氧化产率和85%催化氧化选择性.     

微波法研制碱土金属氧化物负载型MCM-48碱性介孔材料

以立方相介孔分子筛MCM-48为载体,用微波辐射分散MgO或CaO和醋酸镁溶液浸渍等方法研制碱性介孔材料。MCM-48能经受微波辐射,负载碱性客体之后也保持介相结构。异丙醇分解探针反应表明:载体本身没有碱催化活性,而碱性MCM-48介孔材料的活性随温度升高而提高。本文还对介孔材料在微波分散和碱性催化方面的特点进行分析。     

锐钛相虫蛀状介孔二氧化钛的表征

0IntroductionMesostructuredtitania(TiO2)hasattractedagreatdealofattention,inviewofcontrolleddelivery,catalytic,photocatlytic,orenergyconversionapplica-tions犤1犦.Theuseoftitaniumisopropoxidebis-acetylace-tonateprecursors,combinedwithalkylphosphatean-ionicsurfactantsastemplate,ledtothefirstdocu-mentedpuremesoporousTiO2犤2犦.Insubsequentyears,moresyntheticstrategieshavebeendevelopedusingavarietyofstructure-directingagents,forexample,car-boxylicacids犤3犦,alkylamine犤4犦,aminium犤5犦,blockcop-o…     

Formation of supported size-controlled nanoparticles of sulfated zirconia

Methods of the preparation of catalysts for alkane skeletal isomerization based on uniform nanoparticles of sulfated zirconia anchored to different supports were investigated. These catalysts were characterized by using the ICP, HRTEM and BET techniques. The activities of the catalysts in the reaction of n-butane isomerization were measured and compared with those of bulk catalysts.