多级轴流压气机全工况特性计算

本文使用三维粘性流动计算软件Fine／Numeca,对某十五级轴流压气机进行了内流流场和全工况特性的数值计算尝试。分析了该压气机在设计工况和非设计工况的性能,同时把整机计算结果和前七级叶片的计算结果进行了比较。计算结果表明,当计算的级数较少时,目前的软件和硬件平台可以比较合理地预测压气机的全工况特性;而当计算的级数较多时,准确的数值模拟仍需要更为准确的多级模型和数值方法。     

Synthesis of poly(p‐phenylene sulfide) from bis(4‐bromophenyl) disulfide

Improved reaction conditions for the preparation of poly(p‐phenylene sulfide) (PPS) directly from bis(4‐bromophenyl) disulfide (BBD) have been established. Heating BBD with magnesium metal afforded only a low molecular weight polymer. PPS with a melting temperature around 280 °C was obtained from BBD in the presence of sodium carbonate or zinc metal. The best results were obtained with the addition of a catalytic amount of KI to the zinc–BBD mixture. Polymers prepared by the above methods are semicrystalline and dissolve in 1‐chloronaphthalene and have properties comparable to commercial PPS. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 900–904, 2006     

Chemically modified proton‐conducting membranes based on sulfonated polyimides: Improved water stability and fuel‐cell performance

A series of branched/crosslinked sulfonated polyimide (B/C‐SPI) membranes were prepared and evaluated as proton‐conducting ionomers based on the new concept of in situ crosslinking from sulfonated polyimide (SPI) oligomers and triamine monomers. Chemical branching and crosslinking in SPI oligomers with 1,3,5‐tris(4‐aminophenoxy)benzene as a crosslinker gave the polymer membranes very good water stability and mechanical properties under an accelerated aging treatment in water at 130 °C, despite their high ion‐exchange capacity (2.2–2.6 mequiv g^?1). The resulting polymer electrolytes displayed high proton conductivities of 0.2–0.3 S cm^?1 at 120 °C in water and reasonably high conductivities of 0.02–0.03 S cm^?1 at 50% relative humidity. In a single H₂/O₂ fuel‐cell system at 90 °C, they exhibited high fuel‐cell performances comparable to those of Nafion 112. The B/C‐SPI membranes also displayed good performances in a direct methanol fuel cell with methanol concentrations as high as 50 wt % that were superior to those of Nafion 112. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3751–3762, 2006     

Lithographic design of photosensitive polyarylates based on reaction development patterning

The factors affecting pattern‐forming properties in reaction development patterning were examined with polyarylates with various bisphenol moieties. The developability of the photosensitive polyarylates was dependent on the properties of the subtituent (R) in the bisphenol moieties. The development time decreased in the following order: R?C(CH₃)₂ > fluorenyl unit ? phenolphthalein unit > C(CF₃)₂ > SO₂. This order agreed with that of the reactivity between the polyarylates and ethanolamine, and these orders can be explained by pK_a of the bisphenol used to prepare the polyarylates. The development with NH₂? R′? OH resulted in successful positive‐tone pattern formation. However, pattern formation with the developers containing NH₂? R′? OCH₃ was unsuccessful. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2694–2706, 2006     

Evaluation of piezoelectric PVDF polymers for use in space environments. III. Comparison of the effects of vacuum UV and gamma radiation

Films of piezoelectric PVDF and P(VDF‐TrFE) were exposed to vacuum UV (115–300 nm VUV) and γ‐radiation to investigate how these two forms of radiation affect the chemical, morphological, and piezoelectric properties of the polymers. The extent of crosslinking was almost identical in both polymers after γ‐irradiation, but surprisingly, was significantly higher for the TrFE copolymer after VUV‐irradiation. Changes in the melting behavior were also more significant in the TrFE copolymer after VUV‐irradiation due to both surface and bulk crosslinking, compared with only surface crosslinking for the PVDF films. The piezoelectric properties (measured using d₃₃ piezoelectric coefficients and D‐E hysteresis loops) were unchanged in the PVDF homopolymer, while the TrFE copolymer exhibited more narrow D‐E loops after exposure to either γ‐ or VUV‐radiation. The more severe damage to the TrFE copolymer in comparison with the PVDF homopolymer after VUV‐irradiation is explained by different energy deposition characteristics. The short wavelength, highly energetic photons are undoubtedly absorbed in the surface layers of both polymers, and we propose that while the longer wavelength components of the VUV‐radiation are absorbed by the bulk of the TrFE copolymer causing crosslinking, they are transmitted harmlessly in the PVDF homopolymer. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3253–3264, 2006     

Thickness dependence of the magnetic anisotropy of Fe layers separated by Al

Magnetic multilayers of ⁵⁷Fe with nominal thickness, T _nom, between 0.4 and 1.0 nm separated by 3.0 nm Al spacer layers were prepared by alternate deposition of the constituents in high vacuum. The samples were investigated at 4.2 K in external magnetic field. A fraction of Fe atoms corresponding to about 0.3 nm equivalent Fe-thickness was found to mix into the Al spacer. The extremely strong magnetic anisotropy observed for T _nom < 0.8 nm is attributed to Fe layers of approximately two atomic planes thick. The anisotropy decreases considerably after the building up of the third Fe atomic layer starts at T _nom = 0.8 nm, but full saturation was not achieved even for T _nom = 1 nm and 3 T magnetic field applied perpendicularly to the sample plane.     

Formation and magnetic properties of Co–Fe-based bulk metallic glasses with supercooled liquid region

A new Co–Fe-based ferromagnetic bulk metallic glass (BMG) was synthesized by copper mould casting method. The thermal stability and crystallization processes were investigated by differential scanning calorimetry (DSC) and X-ray diffraction (XRD). The soft magnetic behavior was studied by DC magnetic measurements. The high glass formation ability was interpreted in terms of the effective suppression of nucleation and growth of the intermetallic compounds which appear in the multicomponent system during solidification. The high thermal stability indicates that the new Co–Fe-based BMG could be used as high-temperature magnetic material. The low coercivity which was as low as 8 A/m for the as-cast sample was found in the Co–Fe-based metallic glass cylinder with a diameter of 1.5 mm.     

纤维素基磁性聚偕胺肟树脂吸附锂

研究了氯化锂浓度、树脂含量和溶液的ＰＨ对碱式纤维素基磁性聚偕胺肟树脂吸附Ｌｉ＾＋离子能力的影响。在适当条件下，每个偕胺肟基可吸附两个Ｌｉ＾＋离子。     

Sample-path optimization of convex stochastic performance functions

In this paper we propose a method for optimizing convex performance functions in stochastic systems. These functions can include expected performance in static systems and steady-state performance in discrete-event dynamic systems; they may be nonsmooth. The method is closely related to retrospective simulation optimization; it appears to overcome some limitations of stochastic approximation, which is often applied to such problems. We explain the method and give computational results for two classes of problems: tandem production lines with up to 50 machines, and stochastic PERT (Program Evaluation and Review Technique) problems with up to 70 nodes and 110 arcs. Sponsored by the National Science Foundation under grant number CCR-9109345, by the Air Force Systems Command, USAF, under grant numbers F49620-93-1-0068 and F49620-95-1-0222, by the U.S. Army Research Office under grant number DAAL03-92-G-0408, and by the U.S. Army Space and Strategic Defense Command under contract number DASG60-91-C-0144. The U.S. Government has certain rights in this material, and is authorized to reproduce and distribute reprints for Governmental purposes notwithstanding any copyright notation thereon. Sponsored by a Wisconsin/Hilldale Research Award, by the U.S. Army Space and Strategic Defense Command under contract number DASG60-91-C-0144, and the Air Force Systems Command, USAF, under grant number F49620-93-1-0068. Sponsored by the National Science Foundation under grant number DDM-9201813.