手性氨基醇催化的前手性芳酮的不对称还原反应

首次以天然D-樟脑的衍生物为原料, 合成了两个新型龙脑基氨基醇配体, 研究了它们与硼烷原位制备成手性噁唑硼烷后, 在不对称催化氢化还原前手性芳酮中的性能, 得到的手性仲醇的对映体过量(ee)值最高可达96%, 还考察了反应温度、时间、溶剂等因素对苯乙酮的不对称氢化还原的化学产率和光学收率的影响.     

合成方法对MCM-22分子筛的结构、性质及催化性能的影响

在水热条件下分别以动态法和静态法合成了高纯度和高结晶度的MCM-22分子筛.采用N2吸附、XRD、TEM和FTIR等方法研究了制备方法对分子筛的结构及性质的影响.结果表明,动态法合成的MCM-22比静态法合成的分子筛的晶粒小,酸量低.在丙酮一步法合成甲基异丁基酮反应中,静态条件下合成的MCM-22为载体的催化剂的丙酮转化率较高,这是由于该分子筛的酸量较高所致.而MIBK的选择性则呈相反趋势,这可能与动态条件下合成的分子筛粒径小、孔道短有关.     

Colorimetric and ratiometric fluorescent detection of sulfite in water via cationic surfactant-promoted addition of sulfite to α,β-unsaturated ketone

Three fluorescent probes were constructed by incorporating an α,β-unsaturated ketone to a coumarin fluorophore. The selective addition of sulfite to the alkene of TSP assisted by cetyltrimethyl ammonium bromide (CTAB) micelle can be visualized by dramatic color and ratiometric fluorescence changes. In CTAB–PBS system, the fluorescence intensity ratio at 465 nm and 592 nm (I₄₆₅/I₅₉₂) and the absorbance ratio at 390 nm and 470 nm (A₃₉₀/A₄₇₀) were linearly proportional to sulfite concentration in the range of 0.5–150 μM, and the detection limit was 0.2 μM. Good selectivity and competition of TSP1 towards sulfite over several anions and biological thiols were acquired. Probe TSP1 was used to detect sulfite in three realistic samples (mineral water, sugar and white wine) with good recovery.     

丙酮一步法合成甲基异丁基酮催化剂研究

用浸渍法制备了丙酮一步法合成甲基异丁基酮负载型催化剂，考察了载体的预处理温度、添加镧助剂对催化剂性能的影响；用BET法测定了催化剂的表面积；采用H2-O2滴定法测定Pd的分散度．结果发现，用经过1．023K焙烧过的Al2O3为载体的催化剂具有较好的催化性能，添加镧助剂后催化剂的分散度、活性有较大的提高．     

Imide-aryl ether ketone block copolymers

Imide-aryl ether ketone block copolymers were prepared and their morphology and thermal and mechanical properties investigated. Two aryl ether ketone blocks were incorporated; the first was an amorphous block derived from bisphenol–A and the second block was a semi-crystalline poly(aryl ether ether ketone) prepared from a soluble and amorphous ketimine precursor. Bis(amino) aryl ether ketone and aryl ether ketimine oligomers were prepared via a nucleophilic aromaic substitution reaction with molecular weights ranging from 6,000 to 12,000 g/mol. The oligomers were co-reacted with 4,4′-oxydianiline (ODA) and pyromellitic dianhydride (PMDA) diethyl ester diacyl chloride in N-methyl–2-pyrrolidone (NMP) in the presence of N-methylmorpholine. The copolymer compositions, determined by H-NMR, of the resulting amic ester based copolymers ranged from 8 to 50 wt % aryl ether ketone or ketimine content. Prior to imide formation, the ketimine moiety of the aryl ether ketimine block was hydrolyzed (p-toluene sulfonic acid) to the ketone form producing the aryl ether ether ketone block. Compositions of this block were maintained low to retain solubility. Solutions of the copolymers were cast and cured to effect imidization, producing clear films with high moduli (ca. 2200 MPa) and elongations (33–100%). The copolymers displayed good thermal stability with decomposition temperatures in excess of 450°C. Multiphase morphologies were observed irrespective of the co-block type, block length or composition. © 1992 John Wiley & Sons, Inc.     

4,4＇-二苯氧基二苯砜、4,4＇-二苯氧基二苯酮、对苯二甲酰氯三元共聚物的合成

聚醚酮醚酮酮;4;4＇-二苯氧基二苯砜、4;4＇-二苯氧基二苯酮、对苯二甲酰氯三元共聚物的合成;聚醚砜醚酮酮;低温溶液浓缩聚     

Stress-enhanced transport of toluene in poly aryl ether ether ketone (PEEK)

The transport of fluids in the semicrystalline polymer, poly(aryl ether ether ketone) (PEEK), was investigated. Both solubility and rate of penetration of toluene into PEEK are markedly increased by the application of an external stress. The induction period (i.e., the time for the sorption to begin) is a function of applied stress as well as temperature and crystallinity. At 22°C in 29% crystalline PEEK the induction period was reduced from more than 2000 h to approximately 10 h whereas the solubility of toluene was increased from 9 to 44 wt % upon the application of an external tensile stress of 30 MPa. A critical stress (i.e., a stress value below which the stress-enhanced effects are not observed) was determined. The critical stress is a strong function of crystallinity and temperature. © 1996 John Wiley & Sons, Inc.     

Application of the essential work of fracture concept to nanostructured polymer materials

The first part of the paper deals with a critical discussion of the methodical basis of essential work of fracture (EWF) concept with respect to the specimen geometry (especially the notch depth) and application to polymers. In the second part, an in situ testing device, which combines a tensile testing machine with an optical strain-field measuring system, has successfully demonstrated possibility of characterization of fracture behaviour of polystyrene-polybutadiene block copolymers and block copolymer/homopolymer blends as examples of nanostructured polymer materials. It has been shown that knowledge of the time evolution of the strain field close to the crack tips leads to a simple verification of the basic precondition for the applicability of the EWF concept, the precondition “plastic zone coalescence-before-stable crack propagation”.