以四甲基铵硅酸盐为柱化剂合成层柱状MCM-36分子筛

以层状MCM-22P为前驱体,四甲基铵硅酸盐为柱化剂,采用动态水热法考察了MCM-36分子筛的合成条件,并通过XRD、N2物理吸附、TEM、27Al-MAS NMR以及NH3-TPD等手段对合成分子筛进行了表征。结果表明,与传统的采用正硅酸乙酯为柱化剂的柱化过程相比,以四甲基铵硅酸盐为柱化剂时,已溶胀的前驱体不经干燥处理即可直接在含水体系进行柱化插层合成得到层间距均一的层柱状MCM-36分子筛,适宜的合成条件为:先在80℃的高pH值(约13.5)环境下对前驱体溶胀24 h,然后在100℃下柱化插层24 h。表征结果表明,MCM-36分子筛具有层内微孔和层间介孔的复合孔道结构以及较大的比表面积(特别是外比表面积);与HMCM-22相比,HMCM-36的表面酸性虽明显降低,但其层间介孔结构的形成使大量B酸中心暴露于大分子易于接近的层间介孔孔壁,可为涉及较大分子的催化反应提供更多可接近的活性位中心。     

The Effect of Alkaline Addition in Hydrothermal Pretreatment of Empty Fruit Bunches on Enzymatic Hydrolysis Efficiencies

In general, lignocellulosic biomass contains three major components, namely lignin, hemicellulose and cellulose which are the polymers of C5 and C6 sugars. Thus, there is potential to utilize of this biomass for bioethanol production. The hydrolysis of cellulose into glucose was difficult due to the more fibrous nature and thus inhibit enzyme penetration into the cellulose. In order to solve this problem, hydrothermal pretreatment can be used for breaking the bonds within the lignin structure and increase the accessibility of enzyme into the cellulose. In this study, the effect of chemical addition, sodium hydroxide (NaOH) and calcium oxide (CaO) in hydrothermal pretreatment at 180 °C and 30 minutes reaction time of palm oil empty fruit bunches (EFB) on the enzymatic hydrolysis efficiencies was investigated. The enzymatic hydrolysis of hydrothermally pretreated EFB give the highest concentration of glucose at 0.67 g/L while the hydrothermally pretreated of EFB in the presence of NaOH gives the lowest glucose concentration 0.45 g/L.     

柠檬酸配合法制备CuMnCeOx催化剂及常温催化氧化性能研究

摘要：常温催化氧化是消除室内HCHO污染最可行的方法之一,其中以过渡金属氧化物为代表的催化剂因性能优异、成本低廉而备受广泛关注。采用柠檬酸络合法和水热法制备了一系列CuMnCeOx催化剂,研究考察制备方法及载体对催化剂氧化性能的影响,并利用XRD、SEM、BET、H2-TPR、XPS和IR等对催化剂进行微观表征与分析。研究发现,制备方法及载体类型对催化剂的表面结构形貌、氧化性能产生显著影响,其中采用柠檬酸络合法所制的CuMnCeOx-C催化剂性能最佳,48h的HCHO去除率达98.6%,完全满足GB50325-2001标准要求,其介孔结构,晶体粒径及所形成的铈基铜锰固溶体均利于形成大量氧空位及催化氧化反应,且展示出良好的抗水蒸气和稳定性能,其在常温催化氧化VOCs方面具有重要应用前景。     

水热法制备锂电池Si@C负极材料的工艺优化研究

水热法是广泛应用于锂离子电池Si@C电极材料的一种制备方法,其反应条件是影响产物最终形貌和性能的重要因素, 采取最佳的反应工艺可以大大提升材料的电化学性能。本研究中, 使用葡萄糖作为碳源, 光伏切割废料硅为硅源, 探究了水热法制备核壳结构Si@C电极材料的最优工艺, 分别研究了温度、 原料浓度、 反应时间和原料比例对产物的形貌、 性能的影响以及相互之间的关系, 并得到最佳反应条件。在该条件下(葡萄糖浓度为0.5 mol·L^-1, 硅与葡萄糖重量比为0.3:1, 反应温度190 ^oC, 反应时间9 h), 得到了包覆完整、 粒径适中的Si@C电极材料(CS190-3), 对以该样品为负极的扣式半电池进行电化学测试, 在655 mA·g^-1的电流密度下, 其首圈放电比容量为3369.5 mAh·g^-1, 经过500次循环剩余容量为1405.0 mAh·g^-1。倍率测试中, 在6550 mA·g^-1的电流密度下,其剩余容量为937.1 mAh·g^-1,当电流密度恢复至655 mA·g^-1时,电池放电比容量仍可恢复至1683.0 mAh·g^-1。     

Selective solid-phase microextraction of polycyclic aromatic hydrocarbons in water based on oriented phosphorus-containing titanium oxide nanofibers grown on titanium support prior to high-performance liquid chromatography with ultraviolet detection

A novel solid-phase microextraction coating of phosphorous-containing titanium oxide composite was developed using titanium fiber as a support and a titanium source by hydrothermal oxidation in a phosphoric acid solution containing hydrogen peroxide. The morphology of the fiber coatings was controlled by the conditions of the hydrothermal oxidation reaction. The oriented nanofiber coating was employed to extract several types of representative aromatic analytes. The experimental results demonstrated that the as-prepared fiber exhibited excellent extraction efficiency toward polycyclic aromatic hydrocarbons. Combined with high-performance liquid chromatography with ultraviolet detection, main extraction conditions were optimized, including pH, ionic strength, extraction temperature, stirring rate, extraction time and desorption time. The established method presented good linearity from 0.05 to 200 μg/L with limit of detection ranging from 0.012 to 0.126 μg/L. This convenient and green procedure was suitable for the selective extraction and determination of typical polycyclic aromatic hydrocarbons in environmental water samples. The relative recoveries of 85.8–112% were obtained for the determination of target polycyclic aromatic hydrocarbons in water samples spiked with 5.0 and 15.0 μg/L. Moreover, the as-prepared fiber showed at least 210 extraction/desorption cycles due to its high mechanical and chemical stability.     

Jute stick extract assisted hydrothermal synthesis of zinc oxide nanoflakes and their enhanced photocatalytic and antibacterial efficacy

In this paper, we used green and hydrothermal methodology to prepare zinc oxide (ZnO) nanoflakes (NFs) with jute stick extract (J–ZnO NFs) as growth substrate. The prepared materials were characterized using different analytical techniques including ultraviolet–visible spectroscopy (UV–vis), X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), fourier transform infrared (FTIR) spectroscopy, and X-ray photoelectron spectroscopy (XPS). The characteristic absorption peak for ZnO NFs and J–ZnO NFs were observed from the UV–vis spectrum at 373 and 368 nm respectively. The hexagonal wurtzite crystal structure of ZnO NFs and J–ZnO NFs was confirmed by XRD analysis. FESEM and TEM analyses of synthesized J–ZnO NFs confirmed their NFs shape and collectively flower-like structure formation by the assembly of NFs of J–ZnO on cellulose of jute stick extract substrate. The FTIR analysis revealed the functional groups of jute stick extract biomolecules, mainly cellulose, are responsible for the formation of collectivel flower like J–ZnO NFs structure. The XPS analysis revealed the surface and chemical compositions (Zn, C, and O) of J–ZnO NFs. The photocatalytic performance of ZnO NFs and J–ZnO NFs samples was carried out by the degradation of methylene blue (MB) dye solution under UV light irradiation. The degradation efficiency of ZnO NFs and J–ZnO NFs was obtained 79 % and 89 %, respectively, for 5 h. Notably, the degradation efficiency of the J–ZnO NFs was 98 % after 8 h of irradiation, which is very inspiring. The both NFs exhibited first-order kinetics with MB photodegradation. We also examined the possible antibacterial activity of both samples against Escherichia coli (E. coli) pathogens, which demonstrated a significant result with a 17 mm and 19 mm zone of inhibition by ZnO NFs and J–ZnO NFs respectively.     

Synthesis of Fluorescent Carbon Dots and Their Application in Ascorbic Acid Detection

Water-soluble fluorescent carbon dots (CDs) were synthesized by a hydrothermal method using citric acid as the carbon source and ethylenediamine as the nitrogen source. The repeated and scale-up synthetic experiments were carried out to explore the feasibility of macroscopic preparation of CDs. The CDs/Fe³⁺ composite was prepared by the interaction of the CDs solution and Fe³⁺ solution. The optical properties, pH dependence and stability behavior of CDs or the CDs/Fe³⁺ composite were studied by ultraviolet spectroscopy and fluorescence spectroscopy. Following the principles of fluorescence quenching after the addition of Fe³⁺ and then the fluorescence recovery after the addition of asorbic acid, the fluorescence intensity of the carbon dots was measured at λex = 360 nm, λem = 460 nm. The content of ascorbic acid was calculated by quantitative analysis of the changing fluorescence intensity. The CDs/Fe³⁺ composite was applied to the determination of different active molecules, and it was found that the composite had specific recognition of ascorbic acid and showed an excellent linear relationship in 5.0–350.0 μmol·L⁻¹. Moreover, the detection limit was 3.11 μmol·L⁻¹. Satisfactory results were achieved when the method was applied to the ascorbic acid determination in jujube fruit. The fluorescent carbon dots composites prepared in this study may have broad application prospects in a rapid, sensitive and trace determination of ascorbic acid content during food processing.     

响应面法优化Co2+掺杂TiO2制备工艺研究

利用共沉淀-水热法制备了钴掺杂二氧化钛光催化剂,以催化降解水中草甘膦效率为指标,采用响应面法对钴掺杂二氧化钛光催化剂的制备条件进行优化。结果表明,钴掺杂二氧化钛光催化剂的最佳制备工艺为:水热反应温度139.64℃、水热反应时间23.75h、煅烧温度408.17℃和煅烧时间4.04h。利用最佳制备条件下制得的钴掺杂二氧化钛光催化剂催化降解水中草甘膦,降解效率接近80%,与纯二氧化钛相比,催化降解效率有较大幅度提升。     

Facial Synthesis of Adsorbent from Hemicelluloses for Cr(VI) Adsorption

It is challenging work to develop a low-cost, efficient, and environmentally friendly Cr(VI) adsorbent for waste water treatment. In this paper, we used hemicelluloses from chemical fiber factory waste as the raw material, and prepared two kinds of carbon materials by the green hydrothermal method as adsorbent for Cr(VI). The results showed that hemicelluloses hydrothermally treated with citric acid (HTC) presented spherical shapes, and hemicelluloses hydrothermally treated with ammonia solution (HTC-NH₂) provided spongy structures. The adsorption capacity of the samples can be obtained by the Langmuir model, and the adsorption kinetics could be described by the pseudo-second-order model at pH 1.0. The maximum adsorption capacity of HTC-NH₂ in the Langmuir model is 74.60 mg/g, much higher than that of HTC (61.25 mg/g). The green hydrothermal treatment of biomass with ammonia solution will provide a simple and feasible way to prepare adsorbent for Cr(VI) in waste water treatment.