Synthesis of Cationic PEM Emulsion and Application in Waste Water Treatment

Cationic polymer as a kind of flocculant is widely applied in purification treatment of waste water. Because it has positive charge group, it is able to connect strongly the suspended matters, short cellulose and other microparticles. The research on synthesis of cationic polymer and application in treatment of waste water is very universal abroad. But domestic research on those is not general. The technology of synthesis of PEM is simple, and the production cost is low. It is easy to apply in treatment of waste water.Synthesis of PEM Emulsion FlocculantSome distilled water, PVA(poly(vinyl alcohol)), EA(ethyl acrylate), and K2S2O8(potassium persulfate) were put into reaction vessel. Kept stirring up under nitrogen. When heated the solution to 40℃, dropped the water solution of MTA[(2-methacryloxylethyl)trimethyl ammonium].Maintained the temperature at 70℃, reacted about 7-8 hours. Then got the PEM emulsion. Changed the ratio of EA and MTA. Obtained a series of PEM emulsions.Stability and Convertibility of PEM EmulsionThe test results showed that when the EA/MTA was 85/15, the PEM emulsion was most stable.When the total monomer quantity was 35%, the convertibility of PEM emulsion was the highest,i.e.98.6%.The MTA Copolymerization Ratio and Morphology of PEM EmulsionWhen the monomers EA/MTA=85/15 and total monomer quantity was 35%, the MTA copolymerization ratio of PEM emulsion was 95.15%(the highest), and the PEM emulsion was some microspheres with 100-180nm of diameter.The Test Results of PEM Emulsion in Treatment of Waste Water The PEM emulsion flocculant was applied in treatment of waste water of paper mill, and measured the precipitation time(t) and transmittancy(T). The test results were showed in table 1. The optimum value of PEM which was able to make the waste water of paper mill into clear water was 0.008%.     

Nickel Chloride Promoted Glaser Coupling Reaction in Hot Water

A Glaser coupling reaction of terminal alkynes in the presence of nickel chloride withoutany organics and bases in hot water has been developed, which produces the correspondinghomo-coupling products in good yields.     

Non-protein amino acids in peptide design

An overview of the use of non-protein amino acids in the design of conformationally well-defined peptides, based on work from the author’s laboratory, is discussed. The crystal structures of several designed oligopeptides illustrate the useα-aminoisobutyric acid (Aib) in the construction of helices, D-amino acids in the design of helix termination segments and^DPro-Xxx segments for nucleating ofβ-hairpin structures.β- andγ-amino acid residues have been used to expand the range of designed polypeptide structures. Dedicated to Professor C N R Rao on his 70th birthday     

The Convergence and Stability of Splitting Finite-Difference Schemes for Nonlinear Evolutionary Equations

We consider a splitting finite-difference scheme for an initial-boundary value problem for a two-dimensional nonlinear evolutionary equation. The problem is split into nonlinear and linear parts. The linear part is also split into locally one-dimensional equations. We prove the convergence and stability of the scheme in L ₂ and C norms. Printed in Lietuvos Matematikos Rinkinys, Vol. 45, No. 3, pp. 413–434, July–September, 2005.     

铁基添加剂增强细水雾灭火性能的实验研究

采用实验模拟的方法,研究了添加氯化亚铁的细水雾在不同添加剂浓度、不同喷头压力下,熄灭不同性质的液体池火的性能。实验结果表明:添加有氯化亚铁的细水雾,其灭火性能发生了显著变化。存在一个最佳的灭火浓度,其对应的灭火时间最短,耗水量最少,灭火效率最高。细水雾喷头的工作压力和燃料的性质也对细水雾的灭火性能有影响:工作压力越大,细水雾的平均灭火时间越短。在相同的实验条件下,细水雾扑灭煤油池火的时间要短于扑灭酒精池火的时间。     

共振原子蒸气中激光脉冲的时空特性

在柱对称条件下，利用耦合的布洛赫－麦克斯韦方程，研究了激光脉冲在原子蒸气介质中的共振传播。考察了脉中在时空中的演化。数值计算结果表明激光脉冲在传播中，由于自感应透明与光波的衍射效应，表现出复杂的相干现象。     

Identification of nonlinear elliptic equations

An optimization theoretic approach and algorithm for the estimation of state-dependent coefficients in nonlinear elliptic equation is presented. It is based on a splitting method combined with convex analysis techniques. Convergence of the algorithm is established and numerical examples are included.The research of K. Kunisch was supported in part by a grant from the Bundesministerium für Wissenschaft und Forschung, Austria.     

Nano-electrochemical detection of hydrogen or protons using palladium nanoparticles: distinguishing surface and bulk hydrogen.

The benefits of using nanoparticle-modified electrodes are exemplified through the electrochemical detection of protons and/or hydrogen. It is shown that a palladium-nanoparticle-modified boron-doped diamond allows voltammetric information relating to the relative roles played by the surface and the bulk metal to be obtained for the proton-hydrogen system at palladium surfaces which is not accessible using palladium macroelectrodes or microelectrodes.     

Effect of borohydride as reducing agent on the structures and electrochemical properties of Pt/C catalyst

In this paper, we found that boron deposited on the surface of support when sodium borohydride used as reducing agent during the preparation of Pt/C catalyst. The deposition of boron markedly reduces particle size of Pt, raises electrochemical active surface (EAS) area of catalyst and electrochemical activity for hydrogen evolution or oxygen reduction reaction (ORR) compared with which prepared using other reducing agents (hydrogen and formaldehyde).     

Investigations of He implantation and subsequent annealing effects in InP

The influence of 70 keV He⁺ ion implantation and subsequent annealing of Cz-indium phosphide (InP) samples has been investigated using a slow positron beam-based Doppler broadening spectrometer. Three samples with ion fluences of 1 × 10¹⁶, 5 × 10¹⁶ and 1 × 10¹⁷ cm⁻² were studied in the as-implanted condition as well as after annealing at 640 °C for times between 5 and 40 min. It was found that the line-shape parameter of the positron-electron annihilation peak in the implanted layer increases after 5 min annealing, then after longer annealing times it starts to decline gradually until it reaches a value close to the value of the as-grown sample. This implies that vacancy-like defects can be created in InP by He implantation followed by short-thermal annealing at T > 600 °C. Comparison of the results with a study where cavities were observed in He-implanted InP has been carried out.