OCS经由F 31Π里德堡态生成CO(X1Σ+)+S(1D2)产物的波长相关性光解离

本文利用时间切片离子速度成像技术在134∽140 nm波段研究了OCS分子经由F 3¹Π里德堡态的真空紫外光解离动力学. 在选取的5个分别对应OCS(F 3¹Π, v₁=0∽4)的伸缩振动激发的光解波长,实验测得了来自CO(X¹Σ⁺)+S(¹D₂)产物通道的SS(¹D₂))实验影像,并获得了总平动能谱和CO(X¹Σ⁺, v)共生产物的振动布居及角分布. 结果分析表明OCS分子解离生成CO(X¹Σ⁺)+S(¹D₂)产物的过程经历了上态F 3¹Π 与C_?v和C_s构型的下电子态间非绝热耦合过程. 实验结果显示了很强的波长相关性：OCS (F 3¹Π, v₁)的较低转动激发态(v₁=0∽2)和较高转动激发态(v₁=3, 4)的CO(X¹Σ⁺)产物的振动布居和角分布具有显著差异,表明该解离过程中具有不同的解离机理. 本结果提供了振动耦合可能对真空紫外光解离动力学产生关键作用的相关证据.     

Deposition of ZnS thin film by ultrasonic spray pyrolysis: effect of thickness on the crystallographic and electrical properties

Zinc sulfide (ZnS) thin films have been deposited on Si (1 0 0) substrate using ultrasonic spray pyrolysis. X-ray diffraction (XRD) analysis revealed that the films are (0 0 2) preferentially oriented with c-axis-oriented wurtzite structure. The crystallinity has been found to improve with film thickness in the 180–6000 nm range. Film structure has been analyzed by XRD, scanning electron microscope, FTIR, and Raman spectroscopies, while the stoichiometry has been verified by energy-dispersive spectroscopy and particle-induced X-ray emission techniques. Electrical properties of the grown films were characterized by current–voltage and capacitance–voltage measurements where, the films show better conducting behavior at higher thickness.     

Scanning probe microscopy studies of PbS surfaces oxidized in air and etched in aqueous acid solutions

Natural n-type PbS single crystals have been studied using AFM, STM and STS after long-term oxidation in air at ambient temperatures and extensive etching in aqueous acid solutions, in contrast to previous work devoted to initial corrosion of fresh surfaces. The exposure of PbS to atmosphere at high relative humidity for several days yields widespread loose oxidation products; the process is much slower at low humidity. Surface morphologies diverge after the treatment in 1 M perchloric and hydrochloric acid solutions at room temperature and become widely different at elevated temperatures, displaying commonly etch pits up to several micrometers in size and depth along with rather uniformly distributed 20-100 nm protrusions of PbS phase. The changes both in topography and semiconducting properties of PbS found by tunneling spectroscopy have been explained in terms of the non-uniform distribution of donor- and acceptor-type defects D⁺/D⁻ in the metal depleted surface layer, which are generated by chemical reactions and, in turn, determine the rates of the PbS corrosion. In particular, the D⁻ centers exhibit a self-catalyzing effect on the non-oxidative local dissolution of PbS in HCl media, resulting in the deep etch pits.     

Optical properties of cadmium sulfide nanocrystal film prepared by electrochemical synthesis at liquid-liquid interface

Dendritic nanocrystalline CdS film was deposited at liquid-liquid interface of surfactants and an electrolyte containing 4 mmol L⁻¹ cadmium chloride (CdCl₂) and 16 mmol L⁻¹ thioacetamide (CH₃CSNH₂) with an initial pH value of 5 at 15 °C by electrochemical synthesis. The nanofilm was characterized by transmission electron microscopy (TEM), field emission scanning electron microscope (FE-SEM), atomic force microscopy (AFM), ultraviolet visible (UV-vis) absorption spectroscopy and fluorescence spectroscopy. The surface morphology and particle size of the nanofilm were investigated by AFM, SEM and TEM, and the crystalline size was 30-50 nm. The thickness of the nanofilm calculated by optical absorption spectrum was 80 nm. The microstructure and composition of the nanofilm was investigated by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), showing its polycrystalline structure consisting of CdS and Cd. Optical properties of the nanofilm were investigated systematically by UV-vis absorption and fluorescence spectroscopy. A λ_onset blue shift compared with bulk CdS was observed in the absorption spectra. Fluorescence spectra of the nanofilm indicated that the CdS nanofilm emitted blue and green light. The nanocomposites film electrode will bring about anodic photocurrent during illumination, showing that the transfer of cavities produces photocurrent.     

Influence of substrate activation process on structural and optical properties of ZnS thin films

ZnS thin films were deposited on glass substrates by a chemical bath deposition method using a substrate activation process in which aluminum ions become “contaminants” that act as a nucleation center for active components within the deposition solution. The structure and morphology results demonstrate that the films have a ZnS sphalerite crystal structure with a particle size less than 15 nm, and the films consist of small homogeneous grains. The effects of the substrate activation process on the band gap energies and donor-acceptor pair luminescence process were also investigated. A green emission centered at 502 nm was produced due to donor-acceptor transitions from the aluminum acceptor to the ionized and substitution aluminum centers (Al³⁺).     

纯相稀土硫化物红色发光材料的高温微波合成及其光谱性质

采用工业频率为2.45 GHz的高温微波法制备了纯基质相的CaS∶Eu2+红色发光材料,激发波段为410~580 nm,发射峰值波长为654 nm。在微波输入功率为1.0~1.1 k W的条件下,可以获得纯基质相CaS∶Eu2+发光材料;在1.2~1.3 k W功率范围,获得的样品中含有Ca O杂质相,且颗粒团聚严重。其中,1.1 k W制备的CaS∶Eu2+样品相纯度最高,发光性能最优。微波功率的变化本质上揭示了固体颗粒的介电损耗因子及其加热特性的变化,体系涉及的非平衡反应机制促使了纯基质相的形成,并影响材料晶相结构、粒径、形貌和发光性能。结果显示,高温微波制备技术通过控制输入功率及其物料的介电损耗性质,能够获得纯基质相并且颗粒小、团聚少的荧光粉。     

6,8-二甲基-1,2,4-三唑并嘧啶-3-丁二酮基硫醚酮-烯醇互变异构平衡的1HNMR研究

用１ＨＮＭＲ方法研究了不同溶剂和温度对６，８－二甲基－１，２，４－三唑并嘧啶－３－丁二酮基硫醚酮－烯醇互变异构平衡的影响，发现温度升高有利于平衡向酮式转变，而溶剂极性的改变对平衡的影响并不规律，获得了四种溶剂中的ΔＨ和ΔＳ．     

The pure rotational spectrum of ZnS (XΣ)

The pure rotational spectrum of ZnS (X¹Σ⁺) has been measured using direct-absorption millimeter/sub-millimeter techniques in the frequency range 372-471 GHz. This study is the first spectroscopic investigation of this molecule. Spectra originating in four zinc isotopologues (⁶⁴ZnS, ⁶⁶ZnS, ⁶⁸ZnS, and ⁶⁷ZnS) were recorded in natural abundance in the ground vibrational state, and data from the v = 1 state were also measured for the two most abundant zinc species. Spectroscopic constants have been subsequently determined, and equilibrium parameters have been estimated. The equilibrium bond length was calculated to be r_e ∼ 2.0464 Å, which agrees well with theoretical predictions. In contrast, the dissociation energy of D_E ∼ 3.12 eV calculated for ZnS, assuming a Morse potential, was significantly higher than past experimental and theoretical estimates, suggesting diabatic interaction with other potentials that lower the effective dissociation energy. Although ZnS is isovalent with ZnO, there appear to be subtle differences in bonding between the two species, as suggested by their respective force constants and bond length trends in the 3d series.     

Concentrated second‐harmonic generation from a single Al‐covered ZnS nanobelt

Here we report on the hybrid nanostructures where a single ZnS nanobelt was half‐covered with an aluminum (Al) film, which is an ideal platform for studying the second‐harmonic generation (SHG) enhancement effects of the Al coating. It was fabricated by the lift‐off process and allowed for the accurate comparison of the SHG intensity between the Al‐covered and the same bare ZnS nanobelt under consistent test conditions. The results indicate that the Al coating in the hybrid nanostructures not only confines the pumping laser in the ZnS effectively, but also concentrates the emitted SHG signal greatly, increasing the signal collection efficiency. By the combination of these two effects, ∼60 times enhancement of the SHG intensity is achieved at the optimized geometry size (width and thickness) of the ZnS nanobelts. The Al‐based hybrid nanostructures open up new possibilities for low‐cost, highly efficient and directional coherent nanolight sources at short wavelengths.

     

Interaction of H2S with α-Fe2O3(0 0 0 1) surface

The atomic-scale structural changes in an α-Fe₂O₃ (hematite) (0 0 0 1) surface induced by sulfidation and subsequent oxidation processes were studied by X-ray photoemission spectroscopy, LEED, and X-ray standing wave (XSW) measurements. Annealing the α-Fe₂O₃(0 0 0 1) with a H₂S partial pressure of 1 × 10⁻⁷ Torr produced iron sulfides on the surface as the sulfur atoms reacted with the substrate Fe ions. The oxidation state of the substrate Fe changed from 3+ to 2+ as a result of the sulfidation. The XSW measured distance of the sulfur atomic-layer from the unrelaxed substrate oxygen layer was 3.16 Å. The sulfide phase consisted of three surface domains identified by LEED. Formation of the two-dimensional FeS₂ phase with structural parameters consistent with an outermost layer of (1 1 1) pyrite has been proposed. Atomic oxygen exposure oxidized the surface sulfide to a sulfate () and regenerated the α-Fe₂O₃(0 0 0 1) substrate, which was indicated by a (1 × 1) LEED pattern and the re-oxidization of Fe to 3+.